Download Print this page

One For All Home Producer URC 9800 User Manual: Compliance With The Fcc Rules And Regulations; Specifications; Troubleshooting

One for all user guide remote control urc 9800.
Hide thumbs

Advertisement

48
COMPLIANCE WITH THE FCC RULES AND
REGULATIONS
This equipment has been tested and found to comply with the
limits for a class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and radiates radio frequency energy
and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encour-
aged to try and correct the interference by one or more of the fol-
lowing measures:
• Reorient or relocate the receiver antenna.
• Increase the separation between the equipment
and the receiver.
• Connect the equipment into an outlet that is different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/television techni-
cian for help.
The user is cautioned that changes and modifications made to
the equipment without the approval of the manufacturer could
void the user's authority to operate his equipment.
FCC authorization Label
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including
interference that may cause undesired operation.
FCC ID #:
Home Producer: DI2 9800
Command Center:

SPECIFICATIONS

Remote Power.......................................................4 AAA Batteries
RF Command Console Power ...................................120 Volts AC
Remote to RF Command Console Range ........100 Feet (30.48m)
RF Command Console to Device Range .....25 Feet (7.62m) ±30˚
Remote Dimensions (HWD) ...................9 3/8 x 2 7/8 x 1 3/8 4 in.
RF Command Console
Dimensions (HWD) .....................................1 9/16 x 5 1//16 x 4 in.
Remote Weight (without Batteries)..............................8 oz. (220g)
RF Command Console Weight................................10.4 oz (300g)
Specifications are typical. Individual units might vary. Specifications
are subject to change and improvement without notice.

TROUBLESHOOTING

Problem:
Solution
LCD screen begins to
Replace the batteries with
fade, does not appear
four (4) new AAA alkaline
or the red light blinks
batteries.
five times when you
press a key?
The Home Producer
Try all of the codes listed for
does not operate
your brand of home entertain-
your home entertain-
ment component in the "Set-
ment component?
Up Codes" section. If this
does not work, try searching
for your code. Make sure the
home entertainment com-
ponent you are setting up
is able to be operated with
an infrared remote control.
The Home Producer
Try all of the codes listed for
is not performing
your brand of home enter-
commands properly?
tainment component in the
"Set-Up Codes" section.
Many set-up codes may allow
some degree of operation.
However, only one set-up
code will work correctly with
your home entertainment
component.
You make a mistake
During any set up procedure,
when setting up your
except for Macros and Timed
Home Producer?
Sequences, pressing ESC will
return you to [DEVICE and the
TIME] screen without saving. If
you make a mistake program-
ming a Timed Sequence,
return to the Timed Sequence
menu and delete it. If you
make a mistake when saving
a macro, erase it by re-saving
a new macro on the same key.
VCR not recording?
As a safety feature on the
Home Producer, you must
press the REC key twice.
49

Advertisement

   Related Manuals for One for All Home Producer URC 9800

This manual also for:

One for all 9800man

Comments to this Manuals

Symbols: 0
Latest comments: