Screen Saver; Speaker Setting; Av Compulink Mode - JVC XV-SA70BK Instructions Manual

SCREEN SAVER

A television monitor screen may be burned out if a static
picture is displayed for a long time. To prevent this, the
unit automatically activates the screen saver function if a
static picture, such as an on-screen display or menu, is
displayed for over 5 minutes.
• MODE 1
The current picture gets
dark.
• MODE 2
The "screen saver" picture
appears and its brightness
changes.
• OFF
The screen saver function is off.
NOTES
• The monitor screen of a projector or projection TV is
easily burned out if a static picture is displayed for a
long time. Be careful not to allow the monitor screen to
be burned out when you set the SCREEN SAVER mode
to "OFF" .
• The TV screen may be garbled when you set the
SCREEN SAVER mode to "MODE 1" . In this case, set to
another mode.
• When a static picture is displayed for a long time during
playback, the screen saver function is always activated
in "MODE 1" regardless of whether you select "MODE
1" or "MODE 2" .

AV COMPULINK MODE

If you use the AV COMPU
LINK system, you must set
this item correctly.
Select from the three options:
"DVD1" , "DVD2" and "DVD3"
according to the equipment to
be connected.
See page 64.
Downloaded From DvDPlayer-Manual.com JVC Manuals
PREFERENCE1 PREFERENCE2 SPK. SETTING
DIGITAL AUDIO OUTPUT STREAM/PCM
OFF
DOWN MIX
COMPRESSION OFF
DTS BASS MANAGEMENT OFF
AUTO STANDBY OFF
SCREEN SAVER MODE1
AV COMPULINK MODE DVD1
PRESS KEY
PREFERENCE1 PREFERENCE2 SPK. SETTING
DIGITAL AUDIO OUTPUT STREAM/PCM
DOWN MIX OFF
OFF
COMPRESSION
DTS BASS MANAGEMENT OFF
AUTO STANDBY OFF
SCREEN SAVER MODE1
AV COMPULINK MODE DVD1
PRESS KEY

Speaker setting

Speaker Channel setting
Select the speaker
configuration type
according to your speaker
system. Normally, simply
select "5.1 CH." or "2 CH." .
However, by selecting
"EXPERT" , you can make
fine tuning to match your
speaker system.
• 2 CH.
When you connect to a 2-channel amplifier or TV.
• 5.1 CH.
When you connect to a 5.1-channel amplifier and use
the front, rear, center and sub-woofer speakers.
• EXPERT
When you want to make fine tuning to match your
speakers. The following five setting items are
available.
NOTES
• When selecting "5.1 CH." or "EXPERT" , set "DOWN
MIX" to "OFF" (see page 58).
• The Dolby Digital LFE (Low Frequency Effect) signal is
always fed from the SUBWOOFER output on the rear
panel of the unit regardless of speaker setting.
• If you connect the unit's digital output to an external
Dolby Digital or DTS decoder (and set the "DIGITAL
AUDIO OUTPUT" option to "STREAM/PCM"), the
speaker setting above is not effective. Make the speaker
setting of the external decoder properly.
Speaker size settings
(available only when selecting EXPERT)
Sets the speaker sizes
according to your
speakers.
1
Select the speaker to be set using CURSOR
5/∞.
• F.SP: Front speakers
• C.SP: Center speaker
• R.SP: Rear speakers
Initial settings
PREFERENCE1 PREFERENCE2
SPK.SETTING
5.1 CH.
LEVEL
DELAY
F. SP Large
C. SP Small
R. SP Small
BASS S.woofer
PRESS KEY TEST TONE
PREFERENCE1 PREFERENCE2 SPK.SETTING
EXPERT
LEVEL
DELAY
F. SP Large
C. SP Small
R. SP Small
S.woofer
BASS
PRESS KEY
TEST TONE
59