JVC DR-MV1 Instructions Manual page 91

Timer Recording (DVD Deck)
Timer programming cannot be made.
● Date and time is not correct.
]Set date and time correctly. (
● The timer is not engaged.
]Press DVD TIMER (#) and confirm that the DVD timer lamp
lights up on the unit.
● Timer recording is in progress.
]Timer programming can't be performed while a timer recording
is in progress. Wait until it finishes.
Timer programming recording does not start.
● Date and time is not correct.
]Set date and time correctly. (
● The timer is not engaged.
]Press DVD TIMER (#) and confirm that the DVD timer lamp
lights up on the unit.
● There is a power outage while the DVD deck is in the timer
standby mode.
]The unit does not enter timer standby mode automatically when
the power is restored to the unit. Engage the timer standby
mode again.
S V Timer Programming cannot be made.
HOW IEW
● Date and time set on the unit is not correct.
]Set date and time correctly. (
● The channel position does not correspond to that in the
receiving area.
]Set the correct channel position for the receiving broadcast.
( pg. 82)
Automatic Satellite Programme Recording does not start.
● The satellite receiver is not connected properly to this unit.
]Connect the satellite receiver to the L-2 IN/DECODER
connector properly. (
On the front display panel, "– –:– –" appears.
● Power failure occurred.
]Set date and time correctly. (
"PROGRAM FULL" appears on the TV screen during timer
programming.
● Eight programmes have already been timer programmed.
]Clear unnecessary programmes on the unit, then try timer
programming again. (
The disc space does not increase when recorded programmes
are cleared.
● The PC's data recorded on a DVD-RAM drive cannot be cleared
on this unit.
]Format the disc. (When the disc is soiled, wipe the disc with a
soft dry cloth before formatting.) (
Downloaded From DvDPlayer-Manual.com JVC Manuals
pg. 85)
pg. 85)
pg. 85)
pg. 48)
pg. 85)
pg. 47)
pg. 10, 86)
Timer Recording (VCR Deck)
Timer programming cannot be made.
● Date and time is not correct.
]Set date and time correctly. (
● The timer is not engaged.
]Press VCR TIMER (#) and confirm that the VCR timer lamp
lights up on the unit.
● Timer recording is in progress.
]Timer programming can't be performed while a timer recording
is in progress. Wait until it finishes.
Timer programming recording does not start.
● Date and time is not correct.
]Set date and time correctly. (
● The timer is not engaged.
]Press VCR TIMER (#) and confirm that the VCR timer lamp
lights up on the unit.
The VCR Timer lamp on the unit won't stop blinking.
● The timer is engaged but there's no cassette loaded.
]Load a cassette with the record safety tab intact.
● The loaded cassette has had its record safety tab removed.
]Remove the cassette and cover the hole with adhesive tape, or
insert a cassette with the record safety tab intact.
The tape is automatically ejected, then the unit is shut off.
● The end of the tape was reached during timer recording.
]The programme may not have been recorded in its entirety. Next
time make sure you have enough time on the tape to record the
entire programme.
● The end of the tape was reached during Instant Timer
Recording.
]The programme may not have been recorded in its entirety. Next
time make sure you have enough time on the tape to record the
entire programme.
S V Timer Programming cannot be made.
HOW IEW
● Date and time set on the unit is not correct.
]Set date and time correctly. (
● The channel position does not correspond to that in the
receiving area.
]Set the correct channel position for the receiving broadcast.
( pg. 85)
The S V system does not timer-record properly.
HOW IEW
● The unit's channel positions have been set incorrectly.
]Refer to "S V ® System Setup" (
HOW IEW
the procedure.
TROUBLESHOOTING
91
EN
pg. 85)
pg. 85)
pg. 85)
pg. 82) and re-perform