Black & Decker CS1030L Instruction Manual page 24

ENGLISH
Never use defective or incorrect blade washers or bolts.
Follow blade assembly procedures.
ADJUSTMENTS. Before cutting be sure depth and bevel
adjustments are tight.
SUPPORT AND SECURE THE WORK PROPERLY.
Insure that the material to be cut is clamped (Fig. 3) and
solidly supported and balanced on a strong, stable and
level work surface. Support the work so that the wide
portion of the saw shoe is on the portion of the material
that doesn't fall after the cut is made. Never hold cut off
piece by hand (Fig. 4 ). KICKBACK from blade pinch can
result. Keep both hands on saw at all times.
STAY ALERT AND EXERCISE CONTROL. Keep body
positioned to one side of blade. Always maintain a firm
grip and control of saw with both hands. Do not change
hand grip or body position while saw is running. Take
precaution to avoid injury from cut off pieces and other
falling material during operation.
Danger! RELEASE SWITCH IMMEDIATELY IF BLADE
BINDS OR SAW STALLS
SAFETY INSTRUCTIONS - LASERS
Danger! Laser radiation, avoid direct eye exposure,
serious eye injury can result.
Do not use optical tools such as a telescope or transit to
view the laser beam.
Position the laser so unintentional eye contact will be avoided.
Do not operate the laser around children or allow children
to operate the laser.
Do not disassemble. Modifying the product in any way
can increase the risk of laser radiation.
Warning! Use of controls or adjustments or performance
of procedures other than those specified in this manual may
result in hazardous laser radiation exposure.
Do not operate in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust.
Store idle product out of reach of children and other
untrained persons. Lasers / power tools are dangerous in
the hands of untrained users.
Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one laser / power tool, may create a risk of
injury when used on another laser / power tool.
Repairs and servicing MUST be performed by a qualified
repair facility. Repairs performed by unqualified personnel
could result in serious injury.
Do not remove or deface warning labels. Removing labels
increases the risk of exposure to radiation.
For indoor use only.
This product is intended for use in a temperature range of
41°F(5°C) -104°F(40°C).
NOTE: Laser is set at the factory and is not adjustable.
Caution! Use of controls or adjustments or performance of
procedures other than those specified in this manual may
result in hazardous laser radiation exposure.
1. On/off switch
2. Laser on/off switch
3. Main handle
4. Secondary handle
5. Shoe
6. Saw blade
7. Saw blade guard
7a. Blade guard retracting lever
8. Laser
9. Saw blade wrench
ASSEMBLY/ADJUSTMENT SET-UP
Warning! Always unplug saw from power supply
before any of the following operations.
Adjusting the depth of cut (Fig. 7 & 8)
The depth of cut should be set according to the thickness of
the workpiece.
Loosen the lever (11) to unlock the saw shoe.
Move the saw shoe (5) into the desired position. The
corresponding depth of cut can be read from the scale (12).
Tighten the lever to lock the saw shoe in place.
Set depth adjustment of saw such that one tooth of the
blade projects below the workpiece as shown in Fig. 8.
Adjusting the bevel angle (Fig. 9)
This tool can be set to bevel angles between 0° and 45°.
Loosen the locking knob (13) to unlock the saw shoe.
Move the saw shoe (5) into the desired position. The
corresponding bevel angle can be read from the scale (14).
Tighten the locking knob to lock the saw shoe in place.
Removing the blade (Fig. 10 & 11)
Prevent spindle rotation by engaging the teeth of the saw
blade into a piece of scrap wood.
Loosen and remove the blade retaining screw (15) by
turning it counterclockwise using the wrench (9)
supplied.
Remove the outer washer (16).
Remove the saw blade (6).
Attaching the blade
Place the saw blade (6) onto the inner flange (17), making
sure that the arrow on the blade points in the same
direction as the arrow on the tool.
Fit the outer washer (16) on the spindle, with the raised
part pointing away from the saw blade.
24
OVERVIEW