Download  Print this page

Operation; Hints For Optimum Use - Black & Decker CS1030L Instruction Manual

7-1/4” (184mm) circular saw
Hide thumbs

Advertisement

Table of Contents
Insert the blade retaining screw (15) into the hole.
Prevent spindle rotation by engaging the teeth of the saw
blade into a piece of scrap wood.
Securely tighten the blade retaining screw by turning it
clockwise using the wrench (9) supplied.
Warning! To reduce the risk of serious personal injury,
read, understand and follow all important safety warnings and
instructions prior to using tool.
GENERAL CUTS
(IMPORTANT: READ SAFETY WARNINGS AND
INSTRUCTIONS)
Guard against kickback
With unit unplugged, follow all assembly, adjustment and set
up instructions. Make sure lower guard operates. Select the
proper blade for the material to be cut.
Measure and mark work for cutting.
Support and secure work properly (See Safety Rules and
Instructions).
Use appropriate and required safety equipment (See
Safety Rules).
Secure and maintain work area (See Safety Rules).
With plug inserted and guard closed, make sure switch
turns saw on and off.
Warning! It is important to support the work properly and
to hold the saw firmly to prevent loss of control which could
cause personal injury. Fig. 3 illustrates recommended hand
position.

OPERATION

Switch
To operate the tool, depress the trigger switch (1). The
tool will continue to run as long as the trigger is
depressed.
To turn the tool off, release the trigger switch (1). There is
no provision for locking the tool on, and the switch should
never be locked on by any other means.
Kerf plate adjustment (Fig. 12)
The tool is equipped with a sight guide for straight cutting (18)
and for 45° miter cutting (19).
Be sure the saw is unplugged.
Adjust the kerf plate as described below.
Align the left edge of the guides (18) or (19) with the
cutting line.
Keep the kerf plate aligned with the cutting line while sawing.
Work with the shoe pressed against the workpiece.
Adjusting the kerf plate
Plug in the saw.
Make a test cut halfway through a piece of scrap wood.
Withdraw the saw so the cutting line becomes visible.
While keeping the saw in this position, unplug the saw
and loosen the kerf plate on the saw shoe.
Align the 0° mark (18) on the kerf plate with the cutting
line. When adjusting for 45° miter cuts, align the 45° mark
(19) on the kerf plate with the cutting line.
Secure the kerf plate using the screw (20).
Warning! LASER RADIATION. Never aim the beam at a
workpiece with a reflective surface. Bright shiny reflective
sheet steel or similar reflective surfaces are not recommended
for laser use. Reflective surfaces could direct the beam back
toward the operator.
Danger! LASER RADIATION. AVOID DIRECT EYE
EXPOSURE. Do not stare into the laser light source.
Never aim light at another person or object other than the
workpiece. Laser light can damage your eyes.
Warning! DO NOT use tinted glasses to enhance the
laser light. Tinted glasses will reduce overall vision for the
application and interfere with the normal operation of the tool.
Laser switch (Fig. 13)
To turn the laser on, push forward on the laser on/off switch
(2) to activate the laser line (21) as shown in Fig. 13.
To use the laser line
Mark the line that you intend to cut on the workpiece.
Adjust the depth and angle of cut as required.
Push the laser on/off switch (2) to the forward "ON"
position and project the laser beam.
Depress the saw trigger switch (1) and allow the blade to
reach maximum speed.
Place the saw shoe on the workpiece. Align the laser line
with the mark on the workpiece and slowly push the saw
forward keeping the laser line on the mark.
Upon completion of the cut, release the trigger and allow
the saw blade to come to a complete stop before
switching off the laser.
SAWING
Warning! To reduce the risk of serious personal injury,
always hold the tool with both hands.
Let the blade run freely for a few seconds before starting
the cut.
Apply only a gentle pressure to the tool while performing
the cut.
Work with the shoe pressed against the workpiece.

HINTS FOR OPTIMUM USE

As some splintering along the line of cut on the top side of
the workpiece cannot be avoided, cut on the side where
splintering is acceptable.
25
ENGLISH
LASER LINE

Hide quick links:

Advertisement

Table of Contents
loading

  Also See for Black & Decker CS1030L

  Related Manuals for Black & Decker CS1030L