Master/Slave Configuration; Power Cord Daisy Chain - ADJ wifly bar qa5 User Instructions

WiFLY Bar QA5
will stay in the last DMX set up. If power is applied and this mode is
set, the unit will automatically go into the last DMX set up.
• "ProG" (Auto Run) - If the DMX signal is lost or interrupted,
the unit will automatically go into Auto Run mode.
3. Use the UP and DOWN buttons to find your desired DMX state and
press SET UP to confirm and exit.
Battery Life:
This menu is used to check/display the battery life.
1. Plug the fixture in and press the MODE button until "bXXX" is dis
played. "XXX" represents a number between 0-100. The number that
is displayed is the remaining battery life. If "b---" is displayed, it
means either the battery is dead or your running the unit on AC
power.
ADJ RFC:
This function is used to activate and deactivate the ADJ RFC (Remote
Control). When this function is activated you can control the fixture
using the ADJ RFC. Please see the next page for ADJ RFC controls
and functions.
1. Plug the fixture in and press the MODE button until "dXX" is dis-
played.
2. Press the SET UP button until "rFXX" is displayed. "XX" repre-
sents either "on" or "oF".
3. Press the UP or DOWN buttons to either activate the remote func-
tion (On) or deactivate it (Off).
WiFLY Address:
This function is used to set the WiFly address. This address must match
the address that is set to WiFly TransCeiver or WiFly controller.
1. Plug the fixture in and press the MODE button until "rCXX" is dis-
played. "XX" represents a number between 00-14.
2. Press the UP or DOWN buttons to either activate the remote function
(On) or deactivate it (Off).
Dimmer Curve Setting:
1. Plug the fixture in and press the MODE button until "d.XXX" is dis-
played. Now press the SET UP button until "dr-X" is displayed,
"X" representing a number between 0-4.
2. There are 5 dimmer curve settings to choose from. Please see the
Dimmer Curve Diagram Chart on page 28 to see the settings and
ADJ Products, LLC - www.adj.com - WiFLY Bar QA5 User Manual Page 14
Operating Instructions WiFLY Bar QA5
their respective beginning and ending fade times.
Default Mode:
This is a default mode. When this mode is activated all mode's will return
to their default settings.
1. Press the MODE button until "dXX" is displayed.
2. Press the SET UP button until "dEFA" is displayed.
3. Press the UP and DOWN buttons simultaneously. Press the MODE
button to exit.
WiFLY Bar QA5
Master-Slave Configuration:
This function will allows you to link units together to run in a Master-
Slave mode. In a Master-Slave set up one unit will act as the controlling
unit and the others will react to the controlling units built-in programs.
Any unit can act as a Master or as a Slave however, only one unit can be
programmed to act as the "Master."
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the unit.
Use standard XLR data cables to link your units together. Remember
that the Male XLR connector is the input and the Female XLR con-
nector is the ouput. The first unit in the chain (master) will use the
female XLR connector only. The last unit in the chain will use the
male XLR connector only.
2. Set the "Master" unit to your desired mode of operation.
3. On the "Slave" units press the MODE button until "SLAu" is dis-
played. The unit is now set as the "Slave" unit. Each slave unit must
be set to the same setting.
4. Connect the first "Slave" unit to the "Master", and the "Slave" unit
should now start follow the "Master".
WiFLY Bar QA5
With this feature you can connect the fixtures to one another using
the IEC input and output sockets. The quantity that can be con-
nected is 10 fixtures maximum. After 10 fixtures you will need to use
a new power outlet. They must be the same fixtures. DO NOT mix
fixtures.
NOTE: Fixtures cannot be power cord daisy chained and run by bat-
tery power.
ADJ Products, LLC - www.adj.com - WiFLY Bar QA5 User Manual Page 15
Operating Instructions
Master-Slave Configuration

Power Cord Daisy Chain