Table of Contents
Advertisement
Mega GO Bar 50 RGBA
Battery Life:
This menu is used to check/display the battery life.
1. Plug the fixture in and press the MODE button until "bXXX" is dis-
played. "XXX" represents a number between 0-100. The number
that is displayed is the remaining battery life. If "b---" is displayed,
it means either the battery is dead or your running the unit on AC
power.
Mega GO Bar 50 RGBA
Master-Slave Configuration:
This function will allows you to link units together to run in a Master-
Slave mode. In Master-Slave operation one unit will act as the con-
trolling unit and the others will react to the controlling units built-in
programs. Any unit can act as a Master or as a Slave however, only
one unit can be programmed to act as the "Master."
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the
unit. Use standard XLR data cables to link your units together.
Remember that the Male XLR connector is the input and the
Female XLR connector is the ouput. The first unit in the chain
(master) will use the female XLR connector only. The last unit in
the chain will use the male XLR connector only.
2. Set the "Slave" unit to DMX adressing and then connect the
"Slave" unit to the "Master."
3. Set the "Master" unit to your desired mode of operation. The
"Slave" unit will now follow the "Master".
Mega GO Bar 50 RGBA
With this feature you can connect the fixtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 25 fixtures maximum. After 25 fixtures you will need
to use a new power outlet. They must be the same fixtures. DO
NOT mix fixtures.
NOTE: Fixtures cannot be power cord daisy chained and run by
battery power.
ADJ Products, LLC - www.adj.com - Mega GO Bar 50 RGBA User Manual Page 15
Operating Instructions
Master-Slave Configuration
Power Cord Daisy Chain
Mega GO Bar 50 RGBA
The ADJ RFC remote (sold seperately) has many different functions and
allows you to control your Mega GO Bar 50 RGBA from long distance.
The ADJ RFC remote can control your system up to 150 ft. To use the
remote you must first activate the fixtures receiver, to activate the receiv-
er please see the instructions on page 14.
BLACKOUT - Pressing this button will blackout the fixture. Press and
hold this button for 3 seconds to return to default settings and default
running mode.
AUTO RUN - This button will run 1 of 16 automatic programs. You can
scroll through the 16 programs using the "+" and "-" buttons. You can
control the speed of the programs by pressing the SPEED button and
then pressing the "+" and "-" buttons. You can control the fade speed of
the Auto Run by pressing the FLASH button and then pressing the "+"
and "-" buttons.
PROGRAM SELECTION - This button will activate the static color
mode. Use the "+" or "-" to scroll through the 47 colors. Once you have
found your color, you can press the Flash Button to activate strobing and
use the "+" or "-" to adjust the Flash rate.
FLASH - This button will activate the flash (strobe) effect or adjust the
sound sensitivity while in sound active mode. You can adjust the flash
speed or sound sensitivity level by pressing the "+" and "-" buttons.
SPEED - Press this button and use the "+" & "-" buttons to adjust the
speed of the Auto run.
SOUND ACTIVE - This button activates sound active mode. Use the "+"
or "-" to scroll through the 15 sound active programs. Press the FLASH
button and use the "+" & "-" buttons to adjust the sound sensitivity.
R G B A - Press either one of these buttons and the press the "+" or "-"
to adjust the brightness. Press the Flash Button to activate strobing and
use the "+" or "-" to adjust the Flash rate.
"+" and "-" - Use these buttons to adjust the flash rate, speed of the
Auto Run mode, sound sensitivity, and the intensity output of the RGB
colors. These buttons are also used to scroll through the different static
colors, auto run programs, and sound active programs.
ADJ Products, LLC - www.adj.com - Mega GO Bar 50 RGBA User Manual Page 16
ADJ RFC Operation
Advertisement
Table of Contents
