Advertisement
Internal Web Pages
To configure IN1608 HDBT scalers using the factory-installed Web pages in a Web
browser (see the example to the right), connect the Ethernet port on the device to
a LAN or WAN. The default IP address is 192.168.254.254.
Extron Product Configuration Software
To configure IN1608 HDBT scalers using the Extron Product Configuration
Software (PCS), install the software (available on the Extron website,
www.extron.com) to a PC connected to the scaler via Ethernet or front panel USB
Config port. After the installation, start the program. For full instructions, press
<F1> on the keyboard or click the ? button in the software and select Help File.
Basic SIS Command Table
To configure IN1608 HDBT scalers with specific SIS commands via an RS-232,
USB, or Ethernet connection, use the Extron DataViewer utility or a control system
to send and receive SIS commands. The table below lists a selection of SIS commands. For a full list of SIS commands and variables, see the
IN1606 and IN1608 Series User Guide at www.extron.com.
Command
Select audio and video input
Select video input only
Select audio input only
Execute Auto-Image™
Execute Auto-Image and fill
Execute Auto-Image and follow
Mute video to black
Mute video and sync
Unmute video and sync
NOTE:
By default, setting the audio mute with the following commands affects all outputs (configurable through group masters).
Set master audio mute
View master audio mute status
Enable executive mode 1
Enable executive mode 2
Disable executive modes
Set scaler IP address
Set scaler DHCP mode
Set subnet mask
Set gateway IP address
Reboot network
NOTE:
IP settings will not take effect until the
NOTES:
X!
= Input selection (1-8)
X(
= Enable or disable (0 = off or disabled; 1 = on or enabled)
X4)
= IP address (xxx.xxx.xxx.xxx; 192.168.254.254 = default)
X4!
= Subnet mask (xxx.xxx.xxx.xxx; 255.255.0.0 = default)
X4@
= Gateway address (xxx.xxx.xxx.xxx; 0.0.0.0 = default)
Firmware Updates
Download firmware updates from the Extron website and upload them via the internal Web pages or the Extron Firmware Loader program.
Extron USA Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
© 2015 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners.
4
ASCII Command
Response
(Host to Device)
(Device to Host)
X!
X! •
!
In
X!
X! •
&
In
X!
X! •
$
In
A
Img0
]
1*A
]
Img1
2*A
]
Img2
1B
]
Vmt1
2B
]
Vmt2
0B
]
Vmt0
E
X(
}
D7*
GRPM
GrpmD07*
E
}
X(]
D7GRPM
1X
Exe1
]
2X
]
Exe2
0X
]
Exe0
E X4)
}
• X4)]
CI
Ipi
E X(
DH
}
Idh
X(]
E X4!
}
• X4!]
CS
Ips
E X4@
}
• X4@]
CG
Ipg
E
}
2BOOT
Boot2
E
}
2BOOT
command is executed.
Extron USA - West: +1.714.491.1500
Extron USA - East: +1.919.850.1000
Additional Description
]
All
Selects audio and video input
]
RGB
Selects the video only input
]
Aud
Selects the audio only input
Executes an Auto-Image on the current input.
Executes an Auto-Image and fills the output.
Executes an Auto-Image and maintains the aspect ratio of
the current input.
Mutes the video and displays a black output.
Mutes the video and sync output.
Unmutes the video.
X(]
Enable or disable master audio mute.
View the current master audio mute status.
Locks the entire front panel.
Locks the front panel except for input selection and volume
control.
Allows all front panel adjustments and selections.
Specifies a new scaler IP address.
Enables or disables DHCP (0 = default).
Specifies a new subnet mask.
Specifies a new gateway IP address.
]
Restarts the network connection after IP or DHCP changes.
FAX: +1.714.491.1517
FAX: +1.919.850.1001
X!
.
X!
.
X!
.
www.extron.com
68-1916-52 Rev. A
06 15
Advertisement
