Quiet Button; Clock Button; Turbo Button - Gree GEH09AA-K3DNA1B Service Manual

(1) Under Sleep 3 mode, press "Turbo" button for a long time, remote control enters into user individuation sleep setting status, at this
time, the time of remote control will display "1hour ",the setting temperature "88" will display the corresponding temperature of last
setting sleep curve and blink (The fi rst entering will display according to the initial curve setting value of original factory);
(2) Adjust "+" and "-" button, could change the corresponding setting temperature, after adjusted, press "Trubo "button for confi rmation;
(3) At this time, 1hour will be automatically increased at the timer postion on the remote control, (that are "2hours " or "3hours " or
"8hours "), the place of setting temperature "88" will display the corresponding temperature of last setting sleep curve and blink;
(4) Repeat the above step (2)
remote control will resume the original timer display;temperature display will resume to original setting temperature.
Sleep3- the sleep curve setting under Sleep mode by DIY could be inquired:
The user could accord to sleep curve setting method to inquire the presetting sleep curve,enter into user individuation sleep setting
status, but do not change the temperature, press "Turbo" button directly for confirmation.Note: In the above presetting or enquiry
procedure,if continuously within10s, there is no button pressed, the sleep curve setting within 10s, there is no button pressed , the sleep
curve setting status will be automatically quit and resume to display the original displaying. In the presetting or enquiry procedure, press
"ON/OFF" button, "Mode" button, "Timer"button or "Sleep" button, the sleep curve setting or enquiry status will quit similarly.
TEMP button
9
Press this button, you can see indoor set temperature, indoor ambient temperature on indoor unit's display. The setting on remote
controller is selected circularly as below:
When selecting "
selecting " " with remote controller, temperature indicator on indoor unit displays indoor ambie nt temperature; 3s later or within 3s
it receives other remote control signal that will return to display the setting temperature.
Caution:
This model hasn't outdoor ambient temperature display function. While remote controller
can operate " " and indoor unit displays set temperature.
It's defaulted to display set temperature when turning on the unit.
Only for the models with temperature indicator on indoor unit.

QUIET button

10
Press this button, the Quiet status is under the Auto Quiet mode (display "
OFF (there is no signal of "
Fan and Dry mode;Under the Quiet mode (Display"

ClOCK button

11
Press CLOCK button,blinking.
2 seconds increases or decreases the time by 1 minute every 0.5 second and then by 10 minutes every 0.5 second. During blinking
after setting, press CLOCK button again to confi rm the setting, and
/
T-ON T-OFF button
12
Press T-ON button to initiate the auto-ON timer. To cancel the auto-timer program, simply press this button again.
After press of this button,
to adjust the time value. Every press of either button changes the time setting by 1 minute. Holding down either button rapidly changes
the time setting by 1 minute and then 10 minutes. Within 5 Seconds after setting, press TIMER ON button to confi rm.
Press T-OFF button to initiate the auto-off timer. To cancel the auto-timer program, simply press the button again.TIMER OFF setting is
the same as TIMER ON.

TURBO button

13
Press this button to activate / deactivate the Turbo function which enables the unit to reach the preset temperature in the shortest time.
In COOL mode, the unit will blow strong cooling air at super high fan speed. In HEAT mode, the unit will blow strong heating air at super
high fan speed.
26
(3) operation, until 8hours temperature setting fi nished,sleep,curve setting fi nished, at this time, the
no display
" with remote controller or no display, temperature indicator on indoor unit displays set temperature; When
"displayed),after powered on, the Quiet OFF is defaulted. Note: the Quiet function cannot be set up in
Within 5 seconds, pressing + or - button adjusts the present time. Holding down either button above
disappears and "ON "blink s . 00:00 is displayed for ON time setting. Within 5 seconds, press + or - button
Auto
"signal )and Quiet mode (display "
" Under the Quiet mode) the fan speed is not available.
then will be constantly displayed.
Service Manual
" singal) and Quiet
Technical Information