Quick Menu - Onkyo HT-R695 Basic Manual

> Specifications > Settings

Quick Menu

You can quickly adjust settings you frequently use, such as
tone adjustments, etc.
Operation:
You can make the settings on the TV screen while playing
something. Press Q on the remote controller to display the
Quick Menu.
Quick Menu
Tone Bass
Level Treble
AccuEQ
Other
Select the item with the cursor /
controller and press ENTER to confirm your selection.
Use the cursors to change the settings.
• To return to the previous screen, press
• To exit the settings, press Q.
■ Tone
Bass:
Enhance or moderate the bass range of the front speakers.
Treble:
Enhance or moderate the treble range of the front
speakers.
• It cannot be set if the listening mode is Pure Audio
(European, Australian and Asian models) or Direct.
■ Level
Center:
Adjust the speaker level of the center speaker while
24
> Listening Modes > Playback Function
listening to some sound.
Subwoofer:
Adjust the speaker level of the subwoofer while listening to
some sound.
• The adjustment you made will be reset to the previous
status when you turn the unit to standby mode.
■ AccuEQ
AccuEQ Room Calibration:
Enable or disable the equalizer function that corrects for
distortion caused by the acoustic environment of the room.
If this is to be enabled, then normally you should select
"On (All Ch)", and to disable just the front speakers you
should select "On (ex. L/R)". The setting can be separately
set to each input selector.
BD/DVD
Equalizer:
Select "Preset 1" to "Preset 3" configured in "2. Speaker" -
"Equalizer Settings" in the Setup menu. The same sound
field setting is applied all ranges when set to "Off".
Cinema Filter:
buttons of the remote
Adjust the soundtrack that was processed to enhance
its high pitch range, in order to make it suitable for home
theater. This function can be used in the following listening
.
modes: Dolby Digital, Dolby Digital Plus, Dolby Surround,
Dolby TrueHD, Multichannel, DTS, DTS-ES, DTS 96/24,
DTS-HD High Resolution Audio, DTS-HD Master Audio,
DTS Neural:X, DTS Express, Neo:6 Cinema, and DSD.
• It cannot be set if the listening mode is Pure Audio
(European, Australian and Asian models) or Direct.
■ Other
A/V Sync :
If the video is behind the audio, you can delay the audio to
offset the gap. Different settings can be set for each input
selector.
• It cannot be set if the listening mode is Pure Audio
(European, Australian and Asian models) or Direct.
Music Optimizer:
Improve the quality of the compressed audio. Playback
> Basic Manual
Troubleshooting | Appendix
sound of lossy compressed files such as MP3 will be
improved. The setting can be separately set to each input
selector. The setting is effective in the signals of 48 kHz or
less. The setting is not effective in the bitstream signals.
• It cannot be set if the listening mode is Pure Audio
(European, Australian and Asian models) or Direct.
Late Night:
Make small sounds easily heard. It is useful when you
need to reduce the volume while watching a movie late
night. You can enjoy the effect only when playing Dolby
series and DTS series input signals.
• The setting cannot be used in the following cases.
– If "Loudness Management" is set to "Off" when
playing Dolby Digital Plus or Dolby TrueHD
– When the input signal is DTS and "Dialog Control" is
other than 0 dB
Center Spread:
Adjust the width of the sound field of the front channel
when playing in the Dolby Surround listening mode. To
spread the width of the sound field to the left and right, set
to "On". To concentrate sound in the center, set to "Off".
• Depending on the speaker settings, this becomes "Off".
Dialog Control:
You can increase the dialog portion of the audio in 1 dB
steps up to 6 dB so that you can make dialog easier to
hear over background noise.
• This cannot be set for content other than DTS:X.
• We plan to provide support for the DTS:X audio format
through a firmware update for this unit. Center Image is
displayed until the update.
• The effect may not be selectable with some content.
HDMI Out:
Allows you to select the HDMI jack to output video signals
from "MAIN", "SUB", and "MAIN+SUB".