Ssembly; Operation - Wolf Garten Power Edition 40 EA Instruction Manual

ssembly

Fixing of handle
B C
TTENTION! Take care that theswitch cable does not
become caught and crused when folding the handle frame.
1. Fold the handle bar toward the back ( ).
2. Set the handle to the desired height and tighten the two
wing nuts (B).

Operation

Mowing
Hanging the grass bag L
Only when the motor is not running and the
cutting blade is not moving.
1. Lift the protective flap.
2. Hang the grass bag in the chassis with the hooks in the
recesses (see arrow).
3. Replace the protective flap.
Emptying of Grassbox P
• the flap drops down when grassbox is full
• To ensure properfunctioning of the indicator it is important
that the grilles beloware kept clean using a hand brush.
ttention! Disconnect electricity by unplugging
cable at the socket-before proceeding.
Mulching
„Mulching" is a process in which the grass is finely chop-
ped by a special cutting system and then deposited on the
ground. The result is that the grass does not have to be
collected and disposed of. „Mulching" also prevents the lawn
from drying out.
Note:
• Depending on how fast the grass grows, you should mulch
1-2 times each week.
• The grass should not be too high or very wet!
• Walk slowly.
• When cutting, the strips should overlap.
• Do not cut more than 20 cm of grass at a time.
Important!
„Mulching" is not recommended if the lawn is mossy or
matted.
Reason:
The cut grass remains on top fo the moss or matted grass
and cannot reach the ground below.
Remedy:
The lawn should be aerated and fertilized regularly.
Inserting the mulching kit
Make sure that the motor is switched off and the
cutting blade is not moving.
1. Remove the grass bag.
2. ssemble as shown in illustrations
Disassemble: as shown in illustrations
F G
H J
3. Fold the upper handle up and screw it tight with the two
wing nuts (C).
Mount grass catcher D E
See illustrations.
Operating times
Please check noise abatement regulations prevailing in your
country.
Inserting power cable into cable holder K
Insert the power cord into the strain relief as shown in the
illustration.
djustment of cutting height M
Only when mower is stationary and rotating blade
has come to complete standstill.
1. Press button (1).
2. push chassis downwards or pull upwards, as required.
3. Release button at required cutting height (2).
Selection of Cutting height
If possible, mow when grass is dry in order to protect turf. Do not
se cutting position too low when mowing very hight or wet grass.
We recommend an average cutting height of 4,0 - 5,0 cm.
Connecting to the mains
The mower operates from any normal household mains
supply, provided with a 16 mps. fuse.
Note: Use a residual current device (RCD) rated for a
residual current not greater than 30 m .
Starting and Stoping N O
• Switch on motor with mowerplaced on level and firm ground
• not in high grass - alternatively tilt slightly
O
Switch-on motor
1. Depress button and hold (1).
2. Lift up bar (2).
3. release button (1).
Wheel drive on (Power Edition 40 E )
Raise drive bracket (3).
Set speed (Power Edition 40 E )
1st gear B5 (4) = slow (2 km/h).
2nd gear B5 (5) = fast (4 km/h).
Wheel drive off (Power Edition 40 E )
Release drive bracket (3).
O
Switch-off motor
Release bar (2).
Tips for mowing Q R
• lways let cable trail on the cut side of the lawn
• Cable guidance: Place the cable firmly off the lawn or on
the already cur side of the lawn when starting to mow.
• To prevent strips of grass from being left unmowed, the
cutting paths must always overlap a few centimeters
(230 Volts, .C., 50 Hz)
N
O
O
O
Q
R
13