Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Java wsd18-060
Summary of Contents for Java wsd18-060
-
Page 4: Table Of Contents
WSD18 Instructions for use 13.2 Drawing off cappuccino and hot milk with Professional‐Cappuccino Frother ....10 13.3 Cleaning the Professional‐Cappuccino Frother 11 1. Safety information ............2 14. Switching off the Coffee Machine ......11 1.1 Warning ..............2 15. Programming............. 11 1.2 Precautions ............2 15.1 Programming the filter........11 2. Preparing the coffee machine ........3 15.2 Programming the water hardness....12 2.1 ... -
Page 5: Safety Information
18. De‐scaling ..............19 1. Safety information 19. Tips for perfect coffee ..........20 1.1 Warning 20. Messages ..............21 ⑴ Children do not realize the dangers involved in using 21. Problems..............22 electric appliances, for this reason always keep an eye 22. Legal information............22 on children when they use electric appliances. 23. Technical Data............23 ⑵ The coffee machine may only be used by instructed 24. Packing List ..............23 persons. ⑶ Never use a defective coffee machine or a machine with E a defective mains cable. ... -
Page 6: Preparing The Coffee Machine
machine. capacity. ⑸ When disconnecting the mains cable never pull on the 2.3 Fill water tank mains cable or the machine itself. ⑹ Never repair or open the coffee machine yourself. Any Only use fresh, cold water. Never fill in milk, mineral repairs may only be carried out by authorized service water or other liquids. shops using original spare parts and accessories. ⑴ Remove the water tank and rinse it with cold tap water ⑺ The coffee machine is connected to mains supply via a thoroughly (Fig. 4). mains cable. Make sure nobody can trip over the mains ⑵ Then fill the water tank and reinstall it. Make sure to cable. Make sure children and pets cannot reach the install the tank properly, it must engage audibly. machine. ⑻ Never put the coffee machine or individual parts of it 2.4 Fill coffee beans into a dishwasher. To ensure that your machine will work perfectly for a ⑼ Make sure to install the machine at a place with long time and to avoid damage, please note that the sufficient air circulation, to prevent overheating of the grinding gear of your coffee machine is not suitable for machine. coffee beans which were treated, during or after roasting, with additives (e.g. sugar). Such coffee 2. Preparing the coffee machine blends may damage the grinding gear. Any repair costs 2.1 Check supply voltage resulting from the use of such blends are not covered ... -
Page 7: Power Switch
We Recommend: WATER ⑷ Fill the water tank (10) with fresh water. A fine grinding degree _ for bright roasts (the smaller the dots, the finer the grinding) DISPLAY: OPEN TAP A coarse degree _ for dark roasts (the larger the dots, ⑸ Place an empty cup under the replaceable hot water the coarser the grinding) nozzle (16). The grinding degree may only be adjusted while the ⑹ Open the steam / hot water draw‐off tap (14) (Fig. 13). grinding gear is running. DISPLAY: FILLING ⑴ Open the bean tank cover (12) and remove the aroma SYSTEM preservation cover (13). DISPLAY: CLOSE TAP ⑵ To adjust the grinding degree, turn the Rotary Switch ⑺ Close the steam / hot water draw‐off tap (14). (Fig. 2) to the required position. DISPLAY: FILLING SYSTEM 2.6 Power switch HEATING Actuate the power switch (21) on your coffee machine ... -
Page 8: Installation Of Claris Plus Filter Cartridges
LEVEL 1 water hardness degree 1 5. Installation of Claris plus filter cartridges LEVEL 2 water hardness degree 2 If the Claris plus filter cartridge is installed properly, LEVEL 3 water hardness degree 3 de‐scaling of the coffee machine is no longer required. LEVEL 4 water hardness degree 4 When the Coffee Machine leaves the factory it is 5.1 Installing the filter adjusted to LEVEL 3. ⑴ Fold up the cartridge holder. Install the filter cartridge in You can adjust another hardness. To do this, proceed as follows: the water tank, applying a gentle pressure (Fig. 1). ⑴ DISPLAY: READY ⑵ Fold down the cartridge holder again until it engages ⑵ Press the programming key (4), the program LED(23) audibly. ⑶ Fill the water tank with cold, fresh tap water and install and illuminated ring (2) is active. DISPLAY: FILTER‐ it again. ⑶ Turn the Rotary Switch (1) until the following message is ⑷ Press the programming key (4), the program LED(23) displayed: ... -
Page 9: Replacing The Filter
⑼ Open the steam / hot water draw‐off tap (14) (Fig.13). ⑷ Remove the water tank from the machine and empty it. ⑸ Fold up the cartridge holder. Install the filter cartridge DISPLAY: RINSING FILTER in the water tank, applying a gentle pressure (Fig. 1). CLOSE TAP ⑹ Fold down the cartridge holder again until it engages ⑽ Close the steam/hot water draw‐off tap (14), now the audibly. Coffee Machine will heat up to coffee temperature. ⑺ Fill the water tank with cold, fresh tap water and DISPLAY: HEATING reinstall it. PRESS ⑻ Place a sufficiently large jug (approx 1 litre) under the RINSE replaceable hot water nozzle (16) and open the RINSING steam/hot water tap (14). READY DISPLAY: RINSING Now you have activated the filter. In Programming FILTER Mode the water hardness selection function is no CLOSE TAP longer displayed. ⑼ Close the steam / hot water draw‐off tap (14). DISPLAY: HEATING 5.2 Replacing the filter ... -
Page 10: Adjusting The Water Quantity For Coffee
RINSE STRONG ⑵ Press the maintenance key (7), the maintenance You can choose among three strengths at the push of LED(24) is active. a button. The longer you press the draw‐off key for 1 DISPLAY: RINSING cup (5), the stronger your coffee will be (Display: READY MILD/ NORMAL/STRONG). You can adjust the water quantity before the draw‐off 7. Adjusting the water quantity for coffee operation using the Rotary Switch (1). ⑴ DISPLAY: READY The indicated value in ML is a reference value and may ⑵ Put a cup under the adjustable coffee spout (17). deviate from the actual value. ⑶ Press the draw‐off key for 1 cup (5) until the required If you press the draw‐off key for 2 cups (6) the strength is displayed: ... -
Page 11: Drawing Off Pre-Ground Coffee
⑴ DISPLAY: READY value (ML) refers to 1 cup. ⑴ DISPLAY: READY ⑵ Put 1 or 2 cups under the adjustable coffee spout (17). ⑵ Press the draw‐off key for 2 cups (6). ⑶ Open the cover of the filler funnel for pre‐ground coffee DISPLAY: 2 CUPS (11). 120 ML (water quantity last adjusted) DISPLAY: FILL The illuminated ring (2) is active. POWDER ⑶ Turn the Rotary Switch (1) again to select the water ⑷ Fill 1 or 2 level spoonfuls of pre‐ground coffee in the quantity individually: filler funnel for pre‐ground coffee (11) (Fig.11) and For Example: 210 ML close the cover. 2 CUPS DISPLAY: CUP BUTTON ⑷ Your product is being prepared. SELECT ⑸ Press the required draw‐off key for 1 cup (5) or 2 DISPLAY: ... -
Page 12: Drawing Off Steam
Do not replace the replaceable hot water Make sure the nozzle has engaged properly. If the nozzle(16)(see Fig. 5 )directly after drawing off water, nozzle is clogged with dried milk or has not been because the nozzle is hot after the draw‐off operation. attached properly, it might suddenly come off during At the start of the water draw‐off operation there can operation. be splashing avoid direct contact with the skin! During frothing some water will escape the system ⑴ DISPLAY: READY before the actual frothing process. This does not affect the result, e.g. when frothing milk. ⑵ Place a cup under the replaceable hot water nozzle (16). At the start of the steam draw‐off operation there can ⑶ Open the steam / hot water draw‐off tap (14) (Fig. 13). be splashing The 2‐stage frothing jet becomes hot. The illuminated ring (2) is active. Avoid direct contact with the skin! For example, 140 ML Steam can be used for heating liquids and frothing WATER milk for cappuccino. Make sure that the replaceable ⑷ Adjust the required water quantity by turning the Rotary 2‐stage frothing jet (15) is pushed upwards when Switch(1). liquids are heated. To froth liquids, push the 2‐stage For example, 200 ML frothing jet downwards, turning it slightly. WATER ⑴ DISPLAY: READY ⑸ If the required water quantity is reached, the following ⑵ Press the steam pre‐selection key (8). message is displayed: DISPLAY: ... -
Page 13: Drawing Off Steam With The Professional-Cappuccino Frother (Optional)
⑸ If you do not change the steam draw‐off time settings 13.2 Drawing off cappuccino and hot milk with using the Rotary Switch (1), the machine will use the Professional‐Cappuccino Frother settings last adjusted. ⑹ During the steam draw‐off operation, the message ⑴ Fill the milk container with milk or immerse the hose in STEAM is displayed the milk directly. ⑺ When the steam quantity is reached, the message ⑵ Place a cup under the Professional‐Cappuccino Frother CLOSE TAP is displayed (Fig. 8) ⑻ Close the steam / hot water draw‐off tap (14). ⑶ Press the steam pre‐selection key (8). DISPLAY: READY / STEAM READY DISPLAY: HEATING As long as STEAM READY is on view in the display, the STEAM machine is ready to dispense steam. READY ⑷ To draw off steam open the steam/hot water draw‐off 13. Drawing off steam with the Professional‐Cappuccino tap (14)(Fig. 13). Frother (optional) The illuminated ring (2) is active. ⑸ You can adjust the steam draw‐off time individually by The Professional‐Cappuccino Frother is optionally available. Contact your authorized dealer. ... -
Page 14: Cleaning The Professional-Cappuccino Frother
your choice. adjusted such that you can draw off coffee without having to change any settings. However, you can 13.3 Cleaning the Professional‐Cappuccino Frother programme various parameters individually. You can programme the following stages: The Professional‐Cappuccino Frother must be cleaned Filter after each draw‐off operation. Hardness ⑴ Fill water in a container and immerse the hose in it. Aroma ⑵ Draw off steam until the water/steam mixture is clean. Temp ⑶ If necessary, disassemble the Professional‐Cappuccino Time Frother and thoroughly rinse the flow regulator with Unit On water (Fig. 16& 17). Unit Off For proper cleaning, use the machine Auto Cappuccino Cups made Cleaning Agent. This is available at your authorized Language dealer. Daily cleaning is recommended. Display 14. Switching off the Coffee Machine Programming key (4) Use the programming key (4) to open or quit the To ensure perfect operation, please switch your Coffee ... -
Page 15: Programming The Water Hardness
⑴ DISPLAY: READY 15.2 Programming the water hardness ⑵ Press programming key (4) until FILTER appears. Refer to Chapter 4 “Adjusting the water hardness”. The program LED(23) and the illuminated ring (2) is active. 15.3 Programming the aroma INTENSIVE or STANDARD ⑶ Turn the Rotary Switch (1) until Temperature is When the machine leaves the factory, the aroma is set displayed. to Intensive. If requested it can also be set to DISPLAY: TEMP Standard. ⑷ Press the Rotary Switch (1). ⑴ DISPLAY: READY DISPLAY: HIGH ⑵ Press programming key (4) until FILTER appears. The ⑸ Turn the Rotary Switch (1) to change the temperature program LED(23) and the illuminated ring (2) is active. from HIGH to NORMAL (or vice versa). ⑶ Turn the Rotary Switch (1) until Aroma is displayed. DISPLAY: NORMAL DISPLAY: ... -
Page 16: Programming The Automatic Switch-On Time
⑶ Turn the Rotary Switch (1) until MACHINE ON is DISPLAY: TIME ⑷ Now press the Rotary Switch (1) to start programming displayed. the time. DISPLAY: UNIT ON ⑷ Now press the Rotary Switch (1) to start programming DISPLAY: ‐‐:‐‐ ⑸ Turn the Rotary Switch (1) to adjust the hours.. the switch‐on time. DISPLAY: 12:‐‐ DISPLAY: ‐‐:‐‐ ⑹ Press the Rotary Switch (1) to confirm the hour settings ⑸ Turn the Rotary Switch (1) to adjust the hours. and to activate the minutes. DISPLAY: 12:‐‐ ⑹ Press the Rotary Switch (1) to confirm the hour settings DISPLAY: 12:‐‐ ⑺ Turn the Rotary Switch (1) to select the minutes. and to activate the minutes. DISPLAY: 4:05 DISPLAY: 12:‐‐ ⑻ To confirm the new settings, press the Rotary Switch (1). ... -
Page 17: Cup Counter
active. function, this place will show “0”.） ⑶ Turn the Rotary Switch (1) until Unit off is displayed. ⑴ DISPLAY: READY DISPLAY: UNIT OFF ⑵ Press programming key (4) until FILTER appears. ⑸ Now press the Rotary Switch (1) to start programming The program LED(23) and the illuminated ring (2) is the switch‐on time. active. DISPLAY: ‐‐:‐‐ ⑶ Turn the Rotary Switch (1) until CUPS MADE is displayed. ⑹ Turn the Rotary Switch (1) to adjust the hours. DISPLAY: CUPS MADE DISPLAY: 12:‐‐ ⑷ Now press the Rotary Switch (1) to start programming ⑺ Press the Rotary Switch (1) to confirm the hour settings the item CUPS MADE and to activate the minutes. ⑸ The total number of drawn off products is displayed. DISPLAY: 12:‐‐ For example TOTAL 100 ⑻ Turn the Rotary Switch (1) to select the minutes. ⑹ Press one of the draw‐off keys to learn the number of DISPLAY: 12:45 draw‐off operations for the individual products (1 ... -
Page 18: Programming Display 24H/Am/Pm
below instructions to choose the language you want. ML/OZ appears ⑴ DISPLAY: READY ⑸ Turn the Rotary Switch (1) until 24H/AM PM appears ⑵ Press programming key (4) until FILTER appears. ⑹ Press the Rotary Switch (1) The program LED(23) and the illuminated ring (2) is e.g. 24H ⑺ Select a setting of your choice. active. ⑶ Turn the Rotary Switch (1) until LANGUAGE appears. ⑻ Press the Rotary Switch (1) to save the setting. ⑷ Now press the Rotary Switch (1) to start programming DISPLAY: DISPLAY ⑼ Press programming key (4) to quit the programming the item LANGUAGE. ⑸ Turn the Rotary Switch (1) until mode or select the next programming item using the e.g. CZECH appears. Rotary Switch (1). ⑹ Press the Rotary Switch (1) to save the selected DISPLAY: READY language. 15.11 Programming the display for ML/OZ DISPLAY: ... -
Page 19: Maintenance
⑶ Insert the empty and clean trip tray again. DISPLAY: DISPLAY ⑻ Press the programming key (4) to quit the DISPLAY: READY programming mode or select the next programming The red water level indicator appears when the drip item using the Rotary Switch (1). tray is full. DISPLAY: READY 16.3 Drip tray missing 16. Maintenance ⑴ DISPLAY: TRAY 16.1 Filling in water MISSING ⑵ If this information is displayed, the drip tray (20) is not ... -
Page 20: Cleaning The Coffee Machine
⑴ Never use scratching objects, pan cleaners, cleaning filter will appear on the display. Refer to Chapter 5.2 «Replacing the filter». sponges or caustic chemicals to clean the machine. ⑵ Wipe off the case on the inside and outside using a soft, 16.6 Cleaning the coffee machine moist cloth. ⑶ Clean the replaceable hot water nozzle after each use. After 200 draw‐off operations or after 160 rinsing ⑷ After heating milk, draw off some hot water, to clean operations, the coffee machine must be cleaned. A the inside of the replaceable 2‐stage frothing jet, too. message appears on the display, telling you to start the ⑸ Disassemble the 2‐stage frothing jet for proper cleaning cleaning programme. You can still draw off coffee or hot (Fig. 6). water/steam. However, we recommend that you should ⑹ The water tank should be rinsed daily and refilled with clean the machine (Chapter 17) within the next few fresh water. days. ⑺ If the water tank shows signs of scaling, remove the DISPLAY: READY CLEAN scaling using a commercial de‐scaling solvent. Take out the water tank (Fig. 4). ⑻ Remove the Claris filter cartridge, if installed, before 16.7 Coffee machine decalcify descaling the water tank. During operation, the machine will calcify. The degree of scaling depends on the hardness of the water in your 16.9 ... -
Page 21: Cleaning
CLOSE TAP message is displayed, the maintenance LED(24) is ⑶ The COFFEE MACHINE is switched off. active: DISPLAY: EMPTY TRAY 17. Cleaning ⑶ Empty the tray Your coffee machine features an integrated cleaning DISPLAY: TRAY program. The cleaning operation will take some 15 min. MISSING Cleaning tablets which are specially designed for the ⑷ Insert the tray again. Remove the drip grate (19). cleaning programme of your coffee machine are ⑸ Put a container (Fig. 12) under the adjustable coffee available at your authorized dealer. Please note that spout (17). machine defects or residues in the water cannot be DISPLAY: PRESS excluded if you use inappropriate cleaning solvents. RINSE Once started, the de‐scaling operation must not be ⑹ Press the maintenance key (7). interrupted! DISPLAY: CLEANING After each cleaning operation the filler funnel for ... -
Page 22: De-Scaling
⑶ Press the maintenance key (7) until the following was completed successfully. message is displayed, the maintenance LED(24) is 18. De‐scaling active: DISPLAY: EMPTY Your coffee machine features an integrated de‐scaling TRAY program. The de‐scaling operation will take some 60 min. ⑷ Empty the tray De‐scaling tablets which are specially designed for the DISPLAY: MISSING de‐scaling program of your COFFEE MACHINE are TRAY available at your authorized dealer. Please note that ⑸ Insert the tray again. machine defects or residues in the water cannot be ⑹ DISPLAY: OPEN TAP excluded if you use inappropriate de‐scaling solvents. SOLVENT If the coffee machine needs de‐scaling, the IN TANK corresponding message is displayed. You can still draw ⑺ Completely dissolve the content of one blister (3 tablets) off coffee or hot water/steam and start the de‐scaling in a jug containing 0.5 litres of water, and fill the program later. Before starting the de‐scaling program, mixture in the water tank. Reinstall the water tank. ... -
Page 23: Tips For Perfect Coffee
⑾ Empty the tray 19. Tips for perfect coffee DISPLAY: MISSING Height‐adjustable coffee spout (17). TRAY You can adjust the height of the coffee spout to the ⑿ Insert the tray again. size of your cups (Fig. 3) DISPLAY: FILL Grinding degree WATER Refer to Chapter 2.5 «Adjusting the grinding gear». Rinse the water tank thoroughly and fill it with cold, Preheating cups fresh tap water. You can preheat the cups using hot water or steam. ⒀ DISPLAY: OPEN TAP The smaller the coffee you want to draw off, the more ⒁ Open the steam / hot water draw‐off valve (14) (Fig. 13). important preheating is. DISPLAY: DECALC.ON Sugar and cream Stirring coffee/tea will result in heat being released. CLOSE TAP Adding refrigerated cream or milk will reduce the ⒂ Close the steam / hot water draw‐off tap (14). temperature of the coffee significantly. DISPLAY: DECALC.ON EMPTY ... -
Page 24: Messages
20. Messages Display Cause Remedy 1. Water tank is empty 1. Refill water FILL WATER 2. Float defective 2. Rinse or de‐scale water tank 1. Refill beans 1. Bean tank is empty 2. Draw off a cup of coffee. The message will FILL BEANS 2. Although you have refilled beans ,the message disappear only after you have drawn off a still appears cup of coffee 1. Coffee grounds container full 1. Empty coffee grounds container EMPTY GROUNDS 2. Tray reinstalled too early after emptying 2. Wait 5 sec. before reinstalling the tray NO TRAY/ Drip tray not installed properly or missing Install tray properly TRAY MISSING READY CLEAN Cleaning required Start cleaning programme (Chapter 17) READY DECALCIFY De‐scaling required ... -
Page 25: Problems
21. Problems 22. Legal information These operating instructions contain all the information Problem Cause Remedy required for using, operating and maintaining the machine Very loud Foreign body in 1. Drawing off properly. noise coming grinding gear pre‐ground coffee Knowledge of and compliance with the specifications from the still possible contained in these operating instructions is required for grinding gear 2. Have coffee using the machine safely as well as for operational safety machine checked and safety during maintenance. by Service These operating instructions cannot cover any conceivable application. 1. 2‐stage frothing 1. clean 2‐stage The machine was designed for private household use. jet blocked frothing jet Too little Additionally we point out that the content of these 2. 2‐stage frothing 2. Draw off steam froth when operating instructions does not form part of any previous ... -
Page 26: Technical Data
23. Technical Data 24. Packing List 1. Auto‐coffee Machine ........ 1 piece Technical Data Voltage 230 VAC / 120 VAC 2. Cappuccino Frother .......... 1 set Power 1400 W Fuse 10 A / 15 A 3. Operating Instructions ........ 1 piece Energy consumption Standby approx. 0.5 Wh Energy consumption «Ready for 4. Certificate of Approval ........ 1 piece approx. 12.0 Wh draw‐off» mode Pump pressure static, max. 15 bar 5. Warranty Card .......... 1 piece Water tank 1.9 Litres Bean tank capacity 200gr. 6. Powder Scoop ........... 1 piece Coffee grounds container max. 15 portions capacity ...
Need help?
Do you have a question about the wsd18-060 and is the answer not in the manual?
Questions and answers