Table of Contents
Advertisement
Available languages
Available languages
3.4.2 Programming a pause
A
pause
can
be
programmed
at
the
end
of
a selection
in the
same manner as
described in
Section
3.4
1.
ln
our example
a
pause
ls
to
be
entered
after step 9 instead
ofthe repeatfunction
at the end of
the
program.
-
Page
forward
in
the
program
to step
10,
then press the
PAUSE
key
[15].
A
"P"
appears
in
the display. Store the
entry.
STEP
TRACK
t-Ä
F
1
5
10
15
20
25
30
rltlllrrlllrllltr
-
The
CD
player
switches
to pause
afterthe
ninth
program
step.
However.
the
beginning of
the
next step
will
not
yet
be
ac-
cessed.
To
continue the
program.
press the
PAUSE [15] key
on
the
CD player or on
the
remote control. The program
conti-
nues
to
run until
the
next
stop is
reached
or if
none
is
pro-
grammed, until
the
end is
reached.
Note:
lf
a
pause
is
desired
after each step, the AUTOSTOP
[13]
key
can
be
pressed before the start
of
the program
(or in
PLAY
PROGRAN/ N/ODE).
This
activates
the
PAUSE
function
after
each
step.
The pause can be cancelled by pressing the
pause
key
115l
on
the
CD player or on
the
remote control.
Note:
lnstead of
PAUSE.
an
interrupt command can
be
programmed
(STOP
function)
by
following
the above procedure.
ln
this
case
the
sToP [3]
key must
be
pressed rather than
the
PAUSE
[15]
key.
When the program
is
started and
reaches the step
with
the
STOP
command, the program
is
interrupted
and
the
CD
player
switches
to
STOP mode.
3.4.3 Programming
the alarm
function
(CAL.
TONE
[12] key)
ln
certain applications
it
may
be
usefulto signalthe
end
of
a
pro-
gram
or of
a
sequence
within the program
with an'Alarm
tone"
by
programming the
following
step:
-
Program
CAL.
TONE [12] instead of
a
selection number or
a
time, This
is
acknowledged
on the display by a
"C".
-
Store
the
entry (the display advances
to the
next
step).
STEP
TRACK
f-
l-l t-
1
5
10
15
20
25
30
rrrrrrrlllttrrtrl
This alarm
tone
remains
active
until
it
is
muted
by
pressing CAL.
fONE
[12] (causing
the program
to
advance automatically to
the next step), or by
interrupting
the
program with
the
STOP
key.
3.4.4 Power off
function at the end
of
the
program
A command for switching
off
the
CD
player can
be
entered
in
a
program
step:
-
Activate program mode
and page
forward
with
key
[']91
to
the
last
program
step
*1,
e.g.
step
16 if
the
last
program
step
was
'1tr
-
Press POWER
[1] A
"-"
is
displayed.
This
does not power off
the
CD
player
(unless
the
POWER key
is
pressed
twice
in
pro-
gram
mode).
-
Press STORE key.
Start the
program
with
PLAY/NEXT
[4]
The
CD player
switches
itself
off
in
the
last program
step.
STEP
TRACK
tr:
I
r^l
151015202530
rrttlttrlrtrrrlll
16
Hide quick links:
Advertisement
Chapters
Table of Contents
