For safe and correct use, please read this installation manual thoroughly before installing the air-conditioner unit.
INSTALLATIONSHANDBUCH
Zum sicheren und ordnungsgemäßen Gebrauch der Klimageräte das Installationshandbuch gründlich durchlesen.
MANUEL D'INSTALLATION
Veuillez lire le manuel d'installation en entier avant d'installer ce climatiseur pour éviter tout accident et vous assurer d'une utilisation correcte.
MANUAL DE INSTALACIÓN
Para un uso seguro y correcto, lea detalladamente este manual de instalación antes de montar la unidad de aire acondicionado.
MANUALE DI INSTALLAZIONE
Per un uso sicuro e corretto, leggere attentamente questo manuale di installazione prima di installare il condizionatore d'aria.
INSTALLATIEHANDLEIDING
Voor een veilig en juist gebruik moet u deze installatiehandleiding grondig doorlezen voordat u de airconditioner installeert.
MANUAL DE INSTALAÇÃO
Para segurança e utilização correctas, leia atentamente este manual de instalação antes de instalar a unidade de ar condicionado.
Air-Conditioners For Building Application INDOOR UNIT PLFY-P-VLMD-A INSTALLATION MANUAL For safe and correct use, please read this installation manual thoroughly before installing the air-conditioner unit. INSTALLATIONSHANDBUCH Zum sicheren und ordnungsgemäßen Gebrauch der Klimageräte das Installationshandbuch gründlich durchlesen. MANUEL D’INSTALLATION Veuillez lire le manuel d’installation en entier avant d’installer ce climatiseur pour éviter tout accident et vous assurer d’une utilisation correcte.
Page 2
[Fig. 3.1.1] Model name 20 · 25 · 32 40 · 50 63 · 80 100 · 125 1060 1300 1650 2000 More than 1000 More than 500 Lap: 20 [Fig. 3.2.1] ø224 45° ø172 90° 90° 90° • Knockouts are provided at each position as shown in the figure. Use them for your purposes when installing the unit. A Split flow duct end connection B Split flow duct end connection (ø200 knockout on both sides) C Fresh air intake (ø150 knockout)
Page 3
[Fig. 6.2.1] [Fig. 6.3.1] A “0-0 gas” mark B “INNER” mark C “OUTER” mark D Flare insulation (2) E Refrigerant piping (gas) F Refrigerant piping (liquid) G Field refrigerant piping H Pipe insulation (1) A Refrigerant pipe (liquid pipe): HP I Insulation material J Flare B Drain pipe...
Page 4
[Fig. 8.2.3] [Fig. 8.2.1] M1M2 M1M2 M1M2 TB15 TB5 TB15 DC10~13V [Fig. 8.2.2] [Fig. 8.2.4] M1M2 M1M2 M1M2 A Terminal block for indoor transmission cable A Non-polarized DC24~30V B Terminal block for outdoor B Upper level (TB15) transmission cable C Remote Controller C Remote controller (A, B) D Lower level (TB5)
Always use an air cleaner, humidifier, electric heater, and other accesso- - Contaminants on the inside of the refrigerant piping may cause the refriger- ries specified by Mitsubishi Electric. ant residual oil to deteriorate. - Ask an authorized technician to install the accessories. Improper installation •...
• Do not use a refrigerant other than R407C. • Install the power cable so that tension is not applied to the cable. - If another refrigerant (R22, etc.) is used, the chlorine in the refrigerant may - Tension may cause the cable to break and generate heat and cause a fire. cause the refrigerator oil to deteriorate.
3.1. Securing installation and service space A Split flow duct end connection B Split flow duct end connection (ø200 knockout on both sides) [Fig. 3.1.1] (P.2) C Fresh air intake (ø150 knockout) D Fresh air intake • Select a blowout direction suited for room shape, installation site and so on. E To be cut •...
5. Installing the unit 5.1. Hanging the unit body 5.2. Confirming the unit’s position and fix- ing hanging bolts s s s s s Bring the indoor unit to an installation site as it is packed. s s s s s To hang the indoor unit, use a lifting machine to lift and pass through the s s s s s Use the gage supplied with the panel to confirm that the unit body and hanging bolts.
[Fig. 6.3.1] (P.3) [Fig. 6.3.3] (P.3) A “0-0 gas” mark B “INNER” mark A Tape (3) B Fasten with tape. C “OUTER” mark D Flare insulation (2) C Provided tie band (4) E Refrigerant piping (gas) F Refrigerant piping (liquid) Notes: G Field refrigerant piping H Pipe insulation (1)
1. Plug the drain pump test connector (accessory) into the connector on the same 5. After confirmation, turn off the main power, remove the connector, and insert side as the control box. For more details, see the information on the control box the polyethylene plug into its original position.
8.2. Connecting remote controller, indoor 8.3. Connecting electrical connections and outdoor transmission cables (Be sure to prevent terminal screws from loosening.) 1. Remove 2 screws which secures the terminal bed box cover using a screw- (Remote contoroller is optionally available.) driver.
Page 12
This product is designed and intended for use in the residential, commer- cial and light-industrial environment. The product at hand is • Low Voltage Directive 73/23/EEC based on the following • Electromagnetic Compatibility Directive 89/ EU regulations: 336/EEC Please be sure to put the contact address/telephone number on this manual before handing it to the customer.