Page 1
P P P P E E E E A A A A K K K K MIDI SWITCHING PRODUCTS FCB8N PROGRAMMABLE MIDI FOOT CONTROLLER OWNER’S MANUAL Document Rev.1.0.1 Jan.11.2011 www.peak2005.com...
MIDI Channels, and 8 Continuous Controller messages (CC), on any single MIDI Channel, to each PATCH. In 4Pr mode the eight CC messages can be accessed as INSTANT ACCESS controls. The FCB8N also supports 1 expression pedal that can be assigned to any Continuous Controller on any of the 16 MIDI Channels The FCB8N has 2 up/down BANK and 12 PATCH and INSTANT ACCESS selection, high quality, heavy duty tactile foot switches.
#1 to #32. In 12Pr mode they are numbered from #1 to PATCH SWITCHES: In 4Pr mode the FCB8N has 4 Patches in each BANK labelled as P1, P2, or 12 Patches per BANK labelled as 1, 2, 3, …, 12 in 12Pr mode.
Weight approx: 3.0lb (1.4kg) Power Connection The FCB8N has flexible power requirements between 9V-12V, AC or DC, 200mA. You can plug in your power adapter to the 5.5mm/2.1mm barrel connector. Do not use voltage over 12Vdc or 9Vac otherwise the unit will be damaged.
PEAK FCB8N: Programmable MIDI foot controller BASIC OPERATION Please refer to the text that appears under the switches when using the FCB8N unit in the basic operation mode. On power up, the last selected PATCH will be loaded and transmitted (Initial value is BANK#1, PATCH#1 in 12Pr mode).
PEAK FCB8N: Programmable MIDI foot controller Expression Pedal Input (EXP1) Expression pedal input EXP1 available both in 4Pr mode or 12Pr mode. You can enable or disable the expression pedal for each PATCH. The expression pedal can be programmed to send any Control Change on any MIDI channel for each PATCH.
CANCEL switch. Setup Mode Configure the FCB8N to operate in 4Pr mode or 12Pr mode or adjust LED display contrast: 1. Enter Programming Mode. (Please see Programming Mode Entry section) 2. When in Programming Mode press the...
PEAK FCB8N: Programmable MIDI foot controller To change the PATCH setup, press the INC+ DEC- switches. The PATCH setup will be changed between 4Pr mode and 12Pr mode. The BANK/PROGRAM display will show the following: 4.Pr 12.Pr 4.2) LED display contrast adjustment: the...
Page 10
Toggles the value between 0 and 127 on each successive press of the PATCH switch. 6. To save please press SAVE switch or to exit without saving please press CANCEL switch. The FCB8N will return to operating mode. Page 10 of 14...
PEAK FCB8N: Programmable MIDI foot controller Copy Mode Copy mode allows you to copy the current PATCH to any other PATCH. All the settings for the PATCH are copied to the new PATCH. To copy a PATCH: 1. Select the PATCH that you want to copy.
FCB8N will return to operating mode. Factory Restore You can reset the FCB8N to the factory default settings. The data that you saved in the EEPROM memory will be erased and the unit returned back the factory default settings. There are two different numbering systems used by various MIDI equipment manufacturers, either 0 127 or 1 128, 0.
- Value 0-63 = OFF (momentary off value = 0) - Value 64-127 = ON (momentary on value = 127) The FCB8N can transmit 3 Program Change Messages (PC#) and 8 Control Change Messages (CC#) per PATCH. The default is as follows:...
The FCB8N is a standard MIDI foot controller that can be connected to any MIDI equipment via a standard 5 pin MIDI cable. Phantom power into the FCB8N unit via a 7 pin midi cable requires pins 6 and 7 for the power supply. The polarity is not important.