JVC GY-HM790U Service Manual page 23

5.1.3 Firmware version display
(1) Refer to 5.1.2.1 to display the VERSION MENU.
(2) The program number and version of the firmware package
are displayed.
--- VERSION ---
FIRMWARE
EXIT
5.1.4 VERSION CHECK Display
(1) Refer to 5.1.2.2 to display the ADVANCED MENU.
(2) Move the cursor to [VERSION CHECK], then press the
[Set] button or the [Cross-Shaped] button (right).
(3) The numbers and versions of each program are displayed.
--- VERSION CHECK ---
SYS CPU
CAM CPU
MBE CPU
MBE LOADER SPL2191 V
FPGA8
FPGA9
FPGA10
FPGA11
EXIT
5.1.5 ADVANCED FUNCTION Menu operation
(1) Refer to 5.1.2.2 to display the ADVANCED MENU.
(2) Move the cursor to [ADVANCED FUNCTION], then press
the [Set] button or the [Cross-Shaped] buttons (up/down) to
change the parameter.
(3) ADVANCED FUNCTION Menu is displayed.
(4) Move the cursor to the item to be changed, then press the
[Set] button or the [Cross-Shaped] button (right).
(5) The parameter blinks. Press the [Cross-Shaped] buttons
(up/down) to change the parameter.
(6) Press the [Set] button to set the parameter. The parameter
lights up.
(7) Move the cursor to [BACK], then press the [Set] button or
the [Cross-Shaped] button (right) to go back to the upper
layer and finish the setting.
NOTE :
• To cancel the parameter setting change, press the [CAN-
CEL] button or the [Cross-Shaped] button (left) while the
parameter is blinking.
--- ADVANCED FUNCTION ---
IRIS ENF AUTO
PIXEL COMPEN DET CANCEL
AE DETECT PEAK
FAW SENSITIVITY
BATT. DISPLAY
C.REC AUDIO FADE
LOOP REC
SDI OUT..
BACK
SPL V
SPL2188 V
SPL2189 V
SPL2190 V
SPL2192 V
SPL1036 V
SPL1037 V
SPL2195 V
ON
10
FAST
AUTO
ON
OFF
Item
IRIS ENF. OFF
AUTO
ON
PIXEL CANCEL
COMPEN DET
*2
EXECUTE Executes blemish detection.
AE DETECT 10
PEAK
FAW SLOW
SENSITIVITY MIDDLE
FAST
BATT. DISPLAY OFF
AUTO
C.REC AUDIO OFF
FADE*3
ON
LOOP REC OFF
ON
SDI OUT..
*1 The lens iris is set to the auto mode by automatically at the
followings.
(1) When the iris is operated by the RM controller.
(2) When the GAIN, the IRIS and the SHUTTER are setting
to the auto mode.
*2 Available only when the Camera Resolution setting is
1280x720, and the Frame & Bit Rate setting is 60p(HQ) or
60p(SP). Otherwise, [---] is displayed and no selection is
available.
*3 When only recording to the SDHC memory cord, this func-
tion is available.
5.1.5.1 White blemish detection
(1) Open the User Menu, then set [Camera Resolution] in
[Record Format] to 1280x720, and [Frame & Bit Rate] to
60p(HQ) or 60p(SP).
Record Format
File Format
Camera Resolution
Frame & Bit Rate
Back
(2) Open the ADVANCED FUNCTION Menu, change the [PIX-
EL COMPEN DET] parameter to [EXECUTE], and then
press the [Set] button.
Parameter
While in the FULL AUTO mode,
the IRIS mode depends on the
lens IRIS MODE switch setting.
While in the FULL AUTO mode,
the Auto Iris mode is activated
even the Manual Iris mode is se-
lected.*1
Does not execute blemish detec-
tion.
Sets the VIDEO PEAK ratio for AE
control. 0 to 50 (By 5%)
Sets the response speed of the
FAW control.
Does not display the battery infor-
mation.
Follow the BATTERY INFO
MENU setting.
No AUDIO FADE in STBY↔REC.
AUDIO FADE in STBY↔REC.
No LOOP REC.
Endless LOOP REC.
Refer to the 5.1.5.2
(Bold is the factory setting.)
Quick Time
1280x720
60p(HQ)
(No.HC034<Rev.001>)1-23