Bosch AKE 30 Operating Instructions Manual page 17

Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool's operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
Use the power tool, accessories and tool bits
etc., in accordance with these instructions and
in the manner intended for the particular type of
power tool, taking into account the working
conditions and the work to be performed. Use of
the power tool for operations different from those
intended could result in a hazardous situation.
Service
Have your power tool serviced by a qualified re-
pair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Chain Saw Safety Warnings:
Keep all parts of the body away from the saw
chain when the motor is operating. Before you
start the saw, make sure the saw chain is not
contacting anything. A moment of inattention
while operating chain saws may cause entangle-
ment of your clothing or body with the saw chain.
Always hold the chain saw with your right hand
on the rear handle and your left hand on the
front handle. Holding the chain saw with a re-
served hand configuration increases the risk of per-
sonal injury and should never be done.
Wear safety glasses and hearing protection.
Further protective equipment for head, hand,
legs and feet is recommend. Adequate protective
clothing will reduce personal injury by flying debris
or accidental contact with saw chain.
Do not operate a chain saw in a tree. Operation
of a chain saw in a tree, may result in personal in-
jury.
Always keep proper footing and operate the
chain saw only when standing on fixed, secure
and level surface. Slippery or unstable surfaces
such as ladders may cause a loss of balance or
control of the chain saw.
When cutting a limb that is under tension be
alert for spring back. When the tension in the
wood fibres is released the spring loaded limb may
strike the operator and/or throw the chain saw out
of control.
Use extreme caution when cutting brush and
saplings. The slender material may catch the saw
chain and be whipped toward you or pull you off
balance.
17 • F016 L70 362 • TMS • 25.04.06
Carry the chain saw by the front handle with the
saw chain stopped and the guide bar pointing
to the rear. When transporting or storing the
chain saw always fit the guide bar cover. Proper
handling of the chain saw will reduce the likelihood
of accidental contact with the moving saw chain.
Follow instructions for lubricating, chain ten-
sioning and changing accessories. Improperly
tensioned or lubricated chain may either break or
increase the chance for kickback.
Keep handles dry, clean, and free from oil and
grease. Greasy, oily handles are slippery causing
loss of control.
Cut wood only. Don't use chain saw for pur-
poses not intended – for example – Don't use
chain saw for cutting plastic, masonry or non-
wood building materials. Use of the chain saw for
operations different then intended could result in a
hazardous situation.
Causes and Operator Prevention of Kickback:
– Kickback may occur when the nose or tip of the
guide bar touches an object, or when the wood
closes in and pinches the saw chain in the cut.
– Tip contact in some cases may cause a sudden re-
verse reaction, kicking the guide bar up and back
towards the operator.
– Pinching the saw chain along the top of the guide
bar may push the guide bar rapidly back towards
the operator.
– Either of these reactions may cause you to lose
control of the saw which could result in serious per-
sonal injury. Do not rely exclusively upon the safety
devices built into your saw. As a chain saw user,
you should take several steps to keep your cutting
jobs free from accident or injury.
Kickback is the result of tool misuse and/or incorrect
operating procedures or conditions and can be
avoided by taking proper precautions as given below:
Maintain a firm grip, with thumbs and fingers
encircling the chain saw handles, with both
hands on the saw and position your body and
arm to allow you to resist kickback forces. Kick-
back forces can be controlled by the operator, if
proper precautions are taken. Do not let go of the
chain saw.
Do not over reach and do not cut above shoul-
der height. This helps prevent unintended tip con-
tact and enables better control of the chain saw in
unexpected situations.
Only use replacement bars and chains speci-
fied by the manufacturer. Incorrect replacement
bars and chains may cause chain breakage and/or
kickback.
Follow the manufacturer's sharpening and
maintenance instructions for the saw chain. De-
creasing the depth gauge height can lead to in-
creased kickback.
English - 2