Eneo HDD-2080Z03IR D Quick Installation Manual
1/3” hdcctv dome, wdr,
day&night, 1920x1080,
3-9mm, 3x af zoom, infrared,
12/24v
Hide thumbs
Also See for HDD-2080Z03IR D:
- User manual (32 pages) ,
- Quick installation manual (32 pages)
Related Manuals for Eneo HDD-2080Z03IR D
Summary of Contents for Eneo HDD-2080Z03IR D
-
Page 1: Quick Installation Guide
Quick Installation Guide 1/3” HDcctv Dome, WDR, Day&Night, 1920x1080, 3-9mm, 3x AF Zoom, Infrared, 12/24V HDD-2080Z03IR D... -
Page 2: Notes On Safety
Notes on safety Please also pay attention to the enclosed safety instructions, and carefully read through this instruction guide before initial operation. Important points of warning are marked with a caution symbol. Important points of advice are marked with a notice symbol. Parts supplied •... -
Page 3: Part Names
Part names Power cable Flush mount OSD control joy stick 3-Axis gimbal Zoom lens Safty wire Dome cover Bubble dome Power cable Video (BNC) Power supply connector... -
Page 4: Installation Instructions
4. Put the dome cover to the dome base unit and tighten the assembly screws. Plastic Anchor (6x30mm) Torque Wrench Mounting Screw (4x30mm) Optional mounting accessories For information on optional mounting accessories please visit the eneo website at www. eneo-security.com. -
Page 5: Power Supply Connections
Pan & Tilt adjustments 1. Pan limit: Pan is limited to +/- 173°. Do NOT force to rotate the gimbal over the limit to prevent from the internal damage. 2. Tilt limit: Tilt is limited to 25° min ~ 90° max. with reference to the ceiling when the inclination of camera module is 0°, that is, the image is aligned horizontally. - Page 6 the frame rate to 60p/50p is highly recommended. Please check specification of monitor before installation. VIDEO (BNC) AC24V/DC12V (Red wire) AC24V/GND (Black wire) RTX+/RS485 (White wire) RTX-/RS485 (Gray wire) Attach the Signal Assignment Sticker in a visible spot for wiring reference.
-
Page 7: Using Osd Controller
Operating instructions Using OSD controller Setup menu can be accessed and controlled by OSD control joy stick on the side of cam- era unit. Five commands are available with the joy stick. OSD control Joy Stick Video format Switch Video Sub-out Connector Description of the joystick operation 1. -
Page 8: Set The Video Format According To System, Ex-Sdi Or Hd-Sdi
Set the video format according to system, EX-SDI or HD-SDI To select the camera’s output video format (EX-SDI or HD-SDI), use the Video format Switch on the side of the camera (see also “Using OSD controller” for location of the switch). -
Page 9: Direct Control Menu
MENU V5.xx ↵ 1. ZOOM/FOCUS ↵ 2. EXPOSURE 3. SCENE ENHANCE NORMAL 4. 3D-NR 5. DAY/NIGHT ↵ 6. PICT ADJUST ↵ 7. SPECIAL ↵ 8. SYSTEM ↵ 9. EXIT SAVE&EXIT Direct control menu MAIN DEFAULT DESCRIPTION ZOOM/FOCUS Sets FOCUS and ZOOM relative fuctions. Sets EXPOSURE MODE, BRIGHTNESS, SENS-UP, EXPOSURE AGC and MOTION DEBLUR. -
Page 10: Further Information
Further information The manual is available from the eneo web site at www.eneo-security.com or from the CD supplied with this product. - Page 12 Videor E. Hartig GmbH Exclusive distribution through specialised trade channels only. Videor E. Hartig GmbH Carl-Zeiss-Straße 8 63322 Rödermark/Germany Tel. +49 (0) 6074 / 888-0 Technical changes reserved Fax +49 (0) 6074 / 888-100 www.videor.com...