Sony DVP-C660 Service Ma page 8

QQ
3 7 63 1515 0
TV Hookups
This connection is for listening to the sound through TV
speakers (L: left, R: right). Refer to the instructions
supplied with the component to be connected.
z
You can enjoy surround sound using your TV's built-in
speakers
You can use 3D sound imaging to create virtual rear speakers
from the sound of built-in TV speakers without using actual rear
speakers (VES TV: Virtual Enhanced Surround TV). For details,
see page 39.
CD/DVD player
5.1CH OUTPUT S-LINK MEGA COMPONENT VIDEO OUT
CONTROL
CENTER
Y P /B-Y P /R-Y
B R
L
FRONT REAR
WOOFER
CONTROL S
R
IN
PCM/DTS/
DOLBY DIGITAL
L 1 1 1
R 2 2 2
R L COAXIAL OPTICAL
VIDEO S VIDEO
AUDIO IN AUDIO OUT DIGITAL OUT OUT OUT
To AUDIO
To To S VIDEO
OUT VIDEO OUT
OUT
To
S-LINK
: Signal flow
TE
L 13942296513
8
Receiver (Amplifier) Hookups
Connect your receiver (amplifier) as follows.
Refer as well to the instructions supplied with the
component to be connected.
z
You can enjoy surround sounds even if you only connect
front speakers
You can use 3D sound imaging to create virtual rear speakers
from the sound of the front speakers (L, R) without using actual
rear speakers (VES: Virtual Enhanced Surround and VIRTUAL
SEMI MULTI DIMENSION). For details, see page 39.
Required cords
Audio connecting cord (not supplied) (1)
White (L) White (L)
Red (R) Red (R)
S video cord (supplied) (1)
When connecting the cords, be sure to match the color-coded
cord to the appropriate jacks on the components: Red (right) to
Red and White (left) to White. Be sure to make connections firmly
to avoid hum and noise.
CD/DVD player
5.1CH OUTPUT S-LINK MEGA COMPONENT VIDEO OUT
CONTROL
CENTER
Y P /B-Y P /R-Y
B R
L
FRONT REAR
WOOFER
CONTROL S
R
IN
PCM/DTS/
DOLBY DIGITAL
L 1 1 1
R 2 2 2
R L COAXIAL OPTICAL
VIDEO S VIDEO
AUDIO IN AUDIO OUT DIGITAL OUT OUT OUT
To AUDIO To DIGITAL To S VIDEO
OUT (R, L) OUT OUT
(OPTICAL)
Take off the
cap.
To
DIGITAL
OUT
(COAXIAL)
www
To optical digital input
or
or
To coaxial digital input .
: Signal flow
10
http://www.xiaoyu163.com
Required cords
Audio/video/S-link connecting cord (supplied) (1)
Yellow Yellow
White (L) White (L)
Red (R) Red (R)
S-LINK
S-LINK
S video cord (supplied) (1)
When connecting the cords, be sure to match the color-coded
cord to the appropriate jacks on the components: Yellow (video)
to Yellow, Red (right) to Red and White (left) to White. Be sure to
make connections firmly to avoid hum and noise.
If your TV has an S-link connector, you can control the CD/DVD
player from the TV. Connect the TV via the S-LINK connector.
If your TV has an S video input connector, connect the
component via the S VIDEO OUT connector using the supplied S
video cord. You will get a better picture.
Refer to the instructions supplied with the TV to be connected.
To an AC outlet
To S VIDEO
TV
input
INPUT
VIDEO
S VIDEO
L
AUDIO
S-LINK
R
To S-LINK
If you have a digital component such as a receiver (amplifier)
with a digital connector, DAT or MD, connect the component via
the DIGITAL OUT OPTICAL or COAXIAL connector using an
optical or coaxial digital connecting cord (not supplied).
Optical digital connecting cord (not supplied) (1)
Coaxial digital connecting cord (not supplied) (1)
Do not connect the power cord to a switched AC outlet
such as the AC outlet on a receiver (amplifier). Doing so
may cause the Playback Memory, Bookmark, Disc Memo
and menu settings to be cancelled when you turn off the
receiver
.
To an AC outlet
To S VIDEO
TV
input
INPUT
VIDEO
S VIDEO
L
AUDIO
R
Receiver
x ao
DIGITAL IN
(Amplifier) with
y
a digital
OPTICAL
connector, MD
deck, DAT deck,
COAXIAL etc.
i
Receiver
CD
(Amplifier)
L
R
To audio input
http://www.xiaoyu163.com
8
If you connect the player to a monitor or
projector having component video input
connectors that conform to output signals from
the COMPONENT VIDEO OUT (Y, P /B-Y, P
B
connectors on the player
Connect the component via the COMPONENT VIDEO
OUT connectors using three video connecting cords (not
supplied) of the same kind. You will get a better picture.
Monitor or projector
with component video
CD/DVD player
input connectors
COMPONENT VIDEO OUT
COMPONENT
Y P /B-Y P /R-Y VIDEO IN
B R
P
R
P
B
Y
Notes
• Refer to the instructions supplied with the component to be
connected.
• Do not connect this player to a video deck. If you do, noise
may appear in the picture.
VCR TV
Connect
CD/DVD
directly
player
• Depending on the TV or receiver (amplifier), sound distortion
may occur because the audio output level is high. In this case,
set "AUDIO ATT" in "AUDIO SETUP" to "ON" in the setup
display. For details, see page 65.
Q Q
3 6 7 1 3
Note
You cannot enjoy a picture with an S video signal if your TV does
not conform to the S video signal. When your TV does not have
an S VIDEO input, connect the component via the VIDEO INPUT
connector using the supplied audio/video connecting cord
instead of the S video cord. For details, see page 8.
Refer to the instructions supplied with your TV.
Setups for the player when using the
digital connecting cords
Connect the component via the DIGITAL OUT OPTICAL
or COAXIAL connector using an optical or coaxial digital
connecting cord (not supplied). You do not need to use
the audio connecting cord.
Some setup adjustments are necessary for the player
depending on the components to be connected.
Use the setup display to change the various settings.
For details on using the setup display, see page 56.
If your receiver (amplifier) does not have a built-
in Dolby* Digital decoder or DTS decoder
• To listen to the sound through speakers connected
to a receiver (amplifier) which has a digital
connector, or to output the sound to a digital
component such as a DAT or MD deck
Set the "AUDIO SETUP" items in the setup display
(page 65) as shown in the illustration below. These are
the default settings.
AUDIO SETUP
AUDIO ATT: OFF
AUDIO DRC: STANDARD
CENTER SPEAKER EQ:
FLAT
DOWNMIX: DOLBY SURROUND
DIGITAL OUT: ON
Set the
DOLBY DIGITAL: D-PCM
items as
DTS: D-PCM
shown
48kHz/96kHz PCM: 48kHz/16bit
To set, press , then .
ENTER
To quit, press .
DISPLAY
When you have made the connections using an optical or
coaxial digital connecting cord, do not set "DOLBY
DIGITAL" to "DOLBY DIGITAL," "DTS" to "DTS" and
"48kHz/96kHz PCM" to "96kHz/24bit." If you do, a loud
noise will suddenly come out from the speakers, affecting
your ears or causing the speakers to be damaged.
u163
Note
You cannot make direct digital audio recordings of discs recorded
in multichannel surround format using an MD deck or DAT
.
deck.
1-2
2 9 9 4 2 8
Setups for the player
Some setup adjustments are necessary for the player
depending on the TV or other components to be
/R-Y)
R
connected.
Use the setup display to change the various settings.
For details on using the setup display, see page 56.
• To connect the player to a normal TV
In the setup display, set "TV TYPE" in "SCREEN
SETUP" to "4:3 LETTER BOX" (default setting) or "4:3
PAN SCAN." For details, see page 60.
• To connect the player to a TV having the WIDE
MODE function
In the setup display, set "TV TYPE" in "SCREEN
SETUP" to "16:9/4:3 WIDE MODE." For details, see
page 60.
• To connect the player to a wide-screen TV
In the setup display, set "TV TYPE" in "SCREEN
SETUP" to "16:9/4:3 WIDE MODE." For details, see
page 60.
1 5 0 5 8 2 9 9 4
If you have an audio component with a built-in
Dolby Digital decoder or DTS decoder
• When you connect an audio component with a built-
in Dolby Digital decoder A
Set "DIGITAL OUT" in "AUDIO SETUP" to "ON" and
then set "DOLBY DIGITAL" to "DOLBY DIGITAL" in
the setup display (page 66).
• When you connect an audio component with a built-
in DTS decoder B
Set "DIGITAL OUT" in "AUDIO SETUP" to "ON" and
then set "DTS" to "DTS" in the setup display (page 67).
• When you connect an audio component that is
compatible with 96kHz/24bit C
Set "DIGITAL OUT" in "AUDIO SETUP" to "ON" and
then set "48kHz/96kHz PCM" to "96kHz/24bit" in the
setup display (page 67).
AUDIO SETUP
AUDIO ATT: OFF
AUDIO DRC: STANDARD
CENTER SPEAKER EQ: FLAT
DOWNMIX: DOLBY SURROUND
DIGITAL OUT: ON
DOLBY DIGITAL: DOLBY DIGITAL
DTS: DTS
48kHz/96kHz PCM: 96kHz/24bit
To set, press , then .
ENTER
To quit, press .
DISPLAY
Notes
• When you do not connect an audio component with a
built-in Dolby Digital decoder, do not set "DOLBY DIGITAL"
to "DOLBY DIGITAL."
• When you do not connect an audio component with a
built-in DTS decoder, do not set "DTS" to "DTS."
• Do not set to "96kHz/24bit" if your receiver (amplifier) is
not compatible with 96 kHz.
• When you connect the component via the DIGITAL OUT
OPTICAL or COAXIAL connector, the Virtual 3D Surround
effect cannot be heard.
m
co
* Manufactured under license from Dolby Laboratories.
"Dolby," "Pro Logic" and the double-D symbol are trademarks
of Dolby Laboratories.
Confidential unpublished works. ©1992-1997 Dolby
Laboratories. All rights reserved.
9 9
2 8 9 9
9
A
B
C
11