Page 1
DVP-C650D/C653D 3 7 63 1515 0 RMT-D112A SERVICE MANUAL US Model Canadian Model E Model DVP-C650D PX Model DVP-C653D Photo: DVP-C650D SPECIFICATIONS CD/DVD player Jack Output Load impedance Laser Semiconductor laser type level Signal format system NTSC S-LINK Mini jack –...
Page 2
SONY PARTS WHOSE PART NUMBERS APPEAR AS DE FONCTIONNEMENT. NE REMPLACER CES COM- SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- POSANTS QUE PAR DES PIÈCES SONY DONT LES LISHED BY SONY. NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
http://www.xiaoyu163.com 3 7 63 1515 0 TABLE OF CONTENTS Section Title Page Section Title Page Service Note ................4 FL-104 (FUNCTION SWITCH), SW-321 (FUNCTION SWITCH) and CK-88 (CONNECTION) GENERAL Schematic Diagram ............4-51 FL-104 (IF CON) Schematic Diagram ......4-53 FR-154 (IR/POWER SWITCH) This Player Can Play the Following Discs ....
http://www.xiaoyu163.com SERVICE NOTE 3 7 63 1515 0 1. DISASSEMBLY • This set can be disassembled in the order shown below. Case (Page 2-1) Front panel section Rear panel section MB-85 board AU-215 board (Page 2-1) (Page 2-2) (Page 2-1) (Page 2-1) Table ass’y (Page 2-2)
Page 5
http://www.xiaoyu163.com 3 7 63 1515 0 4. NOTE ON MOUNTING GEARS 1) Mount the gear (U/D). (See Fig. 3.) 6) Mount the lock lever (See Fig. 5.) 2) Rotate the gear (U/D) in the direction of the arrow. 7) Mount the spring (lock lever). (See Fig. 5.) (down position) (See Fig.
DVP-C650D/C653D SECTION 1 This section is extracted from instruction 3 7 63 1515 0 GENERAL manual (3-867-237-11) L 13942296513 u163 http://www.xiaoyu163.com...
DVP-C650D/C653D SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 3 7 6 3 1 5 1 5 0 THIS NOTE IS COMMON FOR PRINTED WIRING For schematic Diagram: • Caution when replacing chip parts. BOARDS AND SCHEMATIC DIAGRAMS. New parts must be attached after removal of chip.
DVP-C650D/C653D 3 7 6 3 1 5 1 5 0 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS TK-53 (RF/SERVO) PRINTED WIRING BOARD – Ref. No.: TK-53 board; 3,000 series – There are few cases that the part isn't mounted in this model is printed on this diagram.
DVP-C650D/C653D 3 7 6 3 1 5 1 5 0 SE-91 (SENSOR), LE-24 (LED) PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAM – Ref. No.: SE-91 board and LE-24 board; 2,000 series – There are few cases that the part isn't mounted in this model is printed on this diagram.
DVP-C650D/C653D 3 7 6 3 1 5 1 5 0 MB-85 (SIGNAL PROCESS) PRINTED WIRING BOARD – Ref. No.: MB-85 board; 1,000 series – There are few cases that the part isn't mounted in this model is printed on this diagram.
DVP-C650D/C653D 3 7 6 3 1 5 1 5 0 AU-215 (AUDIO/VIDEO BUFFER) PRINTED WIRING BOARD – Ref. No.: AU-215 board; 2,000 series – There are few cases that the part isn't mounted in this model is printed on this diagram.
DVP-C650D/C653D 3 7 6 3 1 5 1 5 0 FL-104 (FUNCTION SWITCH/IF CON), SW-321 (FUNCTION SWITCH) AND CK-88 (CONNECTION) PRINTED WIRING BOARDS – Ref. No.: FL-104 board, SW-321 board and CK-88 board; 2,000 series – There are few cases that the part isn't mounted in this model is printed on this diagram.
DVP-C650D/C653D 3 7 6 3 1 5 1 5 0 FR-154 (IR/POWER SWITCH) PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAM – Ref. No.: FR-154 board; 2,000 series – There are few cases that the part isn't mounted in this model is printed on this diagram.
DVP-C650D/C653D 3 7 6 3 1 5 1 5 0 HP-114 (HEADPHONE) PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAM – Ref. No.: HP-114 board; 2,000 series – There are few cases that the part isn't mounted in this model is printed on this diagram.
DVP-C650D/C653D 3 7 6 3 1 5 1 5 0 LM-59 (LOADING MOTOR), CK-81 (DRIVE) PRINTED WIRING BOARDS – Ref. No.: CK-81 board; 2,000 series – There are few cases that the part isn't mounted in this model is printed on this diagram.
DVP-C650D/C653D 3 7 6 3 1 5 1 5 0 HS-034SF (SWITCHING REGULATOR) PRINTED WIRING BOARD – Ref. No.: HS-034SF board; 6,000 series – – E, PX – There are few cases that the part isn't mounted in this model is printed on this diagram.
DVP-C650D/C653D 3 7 6 3 1 5 1 5 0 HS-034SU (SWITCHING REGULATOR) PRINTED WIRING BOARD – Ref. No.: HS-034SU board; 6,000 series – – US, Canadian – There are few cases that the part isn't mounted in this model is printed on this diagram.
DVP-C650D/C653D SECTION 6 TEST MODE 3 7 63 1515 0 6-1. GENERAL DESCRIPTION ### Syscon Diagnosis ### Diag All Check The Test Mode allows you to make diagnosis and adjustment eas- No. 2 Version ily using the remote commander and monitor TV. The instructions, diagnostic results, etc.
Page 73
Supplement: How to disconnect mechanical deck Disconnect flat cables connected to the CN002 Model Type and CN003 of MB-85 board. Also, disconnect harness from the CN011. DVP-C650D (US, Canadian) DVP-C650D (E) 5. Supply L 13942296513 DVP-C653D (PX) Caution: Do not conduct this check with a mechanical deck con- nected.
Page 74
http://www.xiaoyu163.com 3 7 63 1515 0 (5-4) ARP to RAM Address Bus 6. AV Decoder Data write → other address read discord check (6-2) 1930 RAM Error 10: ARP → RAM address bus error Data write → read, and accord check Caution: Address and data display in case of an error is Error 13: AVD RAM read data discord different from the display of other diagnosis (de-...
Page 75
http://www.xiaoyu163.com 3 7 63 1515 0 Check Items List Error Codes List 00: Error not detected 01: RAM write/read data discord 2) Version 02: Gate array NG (2-2) Revision 03: EEPROM NG (2-3) ROM Check Sum 04: Flash memory clear error (2-4) Model Type 05: Flash memory write error (2-5) Region...
http://www.xiaoyu163.com 3 7 63 1515 0 6-4. DRIVE AUTO ADJUSTMENT 1. DVD-SL (single layer) [ENTER] Select , insert DVD single layer disc, and press key, and the adjustment will be made through the following steps, then On the Test Mode Menu screen, press key on the remote com- adjusted values will be written to the EEPROM.
Page 77
http://www.xiaoyu163.com 3 7 63 1515 0 2. CD 3. DVD-DL (dual layer) [ENTER] [ENTER] Select , insert CD disc, and press key, and the adjust- Select , insert DVD dual layer disc, and press key, ment will be made through the following steps, then adjusted val- and the adjustment will be made through the following steps, then ues will be written to the EEPROM.
http://www.xiaoyu163.com 3 7 63 1515 0 4. SACD 6-5. DRIVE MANUAL OPERATION [ENTER] Select , insert SACD disc, and press key, and the adjustment will be made through the following steps, then adjusted On the Test Mode Menu screen, select , and the manual opera- values will be written to the EEPROM.
Page 79
http://www.xiaoyu163.com 3 7 63 1515 0 0. Disc Check Memory Disc Type 1. Disc Type Auto Check Disc Check 2. DVD SL 12 cm 3. DVD DL 12 cm 4. CD 12cm 5. SACD 12 cm 6. DVD SL 8 cm 1.
http://www.xiaoyu163.com 3 7 63 1515 0 Reset SLED TILT Reset the Sled and Tilt to initial posi- 6-6. MECHA AGING tion. ### Mecha Aging ### Turn ON/OFF the laser. Turn ON/OFF the spindle. Press OPEN key Focus Search the focus and turn on the focus. Turn ON/OFF the tracking servo.
http://www.xiaoyu163.com 3 7 63 1515 0 How to see Emergency History 6-8. VERSION INFORMATION ## Version Information ## IF con. Ver. x. xxx (xxxx) Group SYScon. Ver. x. xxx (xxxx) Model Region 1 : Emergency Code 2 : Don’t Care These codes are used for verification of software designing.
DVP-C650D/C653D SECTION 7 ELECTRICAL ADJUSTMENTS 3 7 63 1515 0 7-1. POWER SUPPLY ADJUSTMENT In making adjustment, refer to 7-3. Adjustment Related Parts Arrangement. 1. Power Supply Check (HS-034SF/034SU BOARD) Note: During diagnostic check, the characters and color bars can be seen only with the NTSC monitor.
http://www.xiaoyu163.com 3 7 63 1515 0 7-2. ADJUSTMENT OF VIDEO SYSTEM 3. Checking Component Video Output B-Y (MB-85 BOARD) <Purpose> 1. Video Level Adjustment (MB-85 BOARD) This checks component video output B-Y. If it is incorrect, cor- <Purpose> rect colors will not be displayed when connected to, for instance, This adjustment is made to satisfy the NTSC standard, and if not projector.
http://www.xiaoyu163.com 3 7 6 3 1 5 1 5 0 5. Checking Component Video Output Y 7-3. ADJUSTMENT RELATED PARTS ARRANGEMENT (MB-85 BOARD) <Purpose> MB-85 BOARD (SIDE A) This checks component video output Y. If it is incorrect, correct brightness will not be attained when connected to, for instance, projector.
DVP-C650D/C653D SECTION 8 REPAIR PARTS LIST 3 7 63 1515 0 8-1. EXPLODED VIEWS NOTE: The components identified by • The mechanical parts with no reference number in • -XX and -X mean standardized parts, so they may mark ! or dotted line with mark the exploded views are not supplied.
http://www.xiaoyu163.com 3 7 63 1515 0 8-1-4. CHASSIS ASSEMBLY L 13942296513 M991 not supplied The components identified by Les composants identifiés par une mark ! or dotted line with marque ! sont critiques pour la mark ! are critical for safety. sécurité.
http://www.xiaoyu163.com AU-215 3 7 63 1515 0 8-2. ELECTRICAL PARTS LIST NOTE: The components identified by • Due to standardization, replacements in the • Items marked “*” are not stocked since they mark ! or dotted line with mark parts list may be different from the parts speci- are seldom required for routine service.
Need help?
Do you have a question about the dvp-c650d and is the answer not in the manual?
Questions and answers