Audio Setup; Settings For The Speakers; Speaker Setup - Sony DVP-C660 Service Ma

QQ
3 7 63 1515 0
Custom Settings (CUSTOM SETUP)
To change the password
1 After Step 3, select "CHANGE PASSWORD" using
M/m, then press , or ENTER.
The display for changing the password appears.
2 Follow Steps 2 and 3 to enter a new password.
Playing a disc which is blocked by the playback
limitation level
1 Insert the disc and press H.
The PARENTAL CONTROL display appears.
2 Enter your 4-digit password using the number buttons,
then press ENTER.
The player starts playback.
When you stop playing the DVD, the level returns to
the original level.
z
If you forget your password
Enter the 6-digit number "199703" whenever the PARENTAL
CONTROL display asks you for your password, then press
ENTER. The display will ask you to enter a new 4-digit
password.
Notes
• When you play DVDs which do not have the Parental Control
function, playback cannot be limited on this player.
• If you do not set a password, you cannot change the settings
for playback limitation.
• Depending on the DVD, you may be asked to change the
parental control level while playing the disc. In this case, enter
your password, then change the level.
When you stop playing the DVD, the level returns to the
original level.
• The same password is used for both Parental Control and
Custom Parental Control (page 43).
TE
L 13942296513
64
Settings for the Sound (AUDIO SETUP)
x CENTER SPEAKER EQ (equalizer)
Makes the spoken track clear by changing the frequency
response when speech is difficult to hear. A center speaker
must be connected to the CENTER connector of 5.1CH
OUTPUT for this function to work.
• FLAT: outputs the spoken track as it was recorded.
• ENHANCED: enhances the spoken track only.
• SOFT: makes the sound softer by rounding out the
sound frequency above 8 kHz. Select this when the
spoken track sounds shrill.
x DOWNMIX
Switches the mixing down methods when you play a
DVD on which rear signal components such as LS, RS, or
S are recorded in Dolby Digital or DTS format. For details
on the rear signal components, see "Displaying the audio
information of the disc" (page 36).
This affects the output from the DIGITAL OUT connectors
only when "DOLBY DIGITAL" is set to "D-PCM" and
"DTS" to "D-PCM" in "DIGITAL OUT."
• DOLBY SURROUND: when the player is connected to
an audio component that conforms to Dolby Surround
(Pro Logic). The output signals which reproduce the
Dolby Surround (Pro Logic) effect are mixed down to 2
channels.
• NORMAL: when the player is connected to an audio
component that does not conform to Dolby Surround
(Pro Logic). The signals without the Dolby Surround
(Pro Logic) effect are output.
x DIGITAL OUT
Selects output signals via the DIGITAL OUT OPTICAL
and COAXIAL connectors.
• ON: Normally select this position. When you select
"ON," set "DOLBY DIGITAL," "DTS" and "48kHz/
96kHz PCM." For details on setting these items, see
"Setting the Digital Output Signal."
• OFF: when the player does not output the sound signals
via the DIGITAL OUT OPTICAL and COAXIAL
connectors, the influence of the digital circuit upon the
analog circuit is at a minimum.
Note www
When you select "OFF," you cannot set "DOLBY DIGITAL,"
"DTS" and "48kHz/96kHz PCM."
.
66
http://www.xiaoyu163.com
Standard Code number
Argentina 2044
Australia 2047
Austria 2046
Belgium 2057
Brazil 2070
Canada 2079
Chile 2090
China 2092
Denmark 2115
Finland 2165
France 2174
Germany 2109
Hong Kong 2219
India 2248
Indonesia 2238
Italy 2254
Japan 2276
Korea 2304
Malaysia 2363
Mexico 2362
Netherlands 2376
New Zealand 2390
Norway 2379
Pakistan 2427
Philippines 2424
Portugal 2436
Russia 2489
Singapore 2501
Spain 2149
Sweden 2499
Switzerland 2086
Taiwan 2543
Thailand 2528
United Kingdom 2184
Setting the Digital Output Signal
Switches the methods of outputting audio signals when
you, connect 1. a digital component such as a receiver
(amplifier) having a digital connector, 2. an audio
component having a built-in decoder (Dolby Digital or
DTS), 3. a DAT or MD via the DIGITAL OUT OPTICAL or
COAXIAL connector using an optical or coaxial digital
connecting cord. For connection details, see page 11.
You cannot adjust "DOLBY DIGITAL," "DTS" and
"48kHz/96kHz PCM" if you set "DIGITAL OUT" to
"OFF."

AUDIO SETUP

AUDIO ATT: OFF
AUDIO DRC: STANDARD
CENTER SPEAKER EQ: FLAT
DOWNMIX: DOLBY SURROUND
DIGITAL OUT: ON
DOLBY DIGITAL: D-PCM
DTS: D-PCM
48kHz/96kHz PCM: 48kHz/16bit
To set, press , then .
ENTER
To quit, press .
DISPLAY
x DOLBY DIGITAL
Selects the Dolby Digital signals to be output via the
DIGITAL OUT OPTICAL and COAXIAL connectors.
• D-PCM (Downmix PCM): when the player is connected
to an audio component lacking a built-in Dolby Digital
decoder. If you play Dolby Digital sound tracks, the
output audio signals are mixed down to 2 channels.
You can select whether the signals conform to Dolby
Surround (Pro Logic) or not by making adjustments to
the "DOWNMIX" item in "AUDIO SETUP."
• DOLBY DIGITAL: when the player is connected to an
audio component with a built-in Dolby Digital decoder.
If the player is connected to an audio component
lacking a built-in Dolby Digital decoder, do not set this.
Otherwise, when you play the Dolby Digital sound
track, a loud noise (or no sound) will come out from the
speakers, affecting your ears or causing the speakers to
be damaged.
x ao u163
y
i
http://www.xiaoyu163.com
2 9
8
x PLAYBACK MEMORY
The player can store the SUBTITLE, VIDEO EQUALIZER,
and other settings of each disc for up to 300 discs
(Playback Memory).
Set the Playback Memory function on or off.
• ON : stores the settings in memory when you eject the
disc.
• OFF : does not store the settings in memory.
The following settings are stored in memory by the
Playback Memory function.
– AUDIO (page 35)*
– SUBTITLE (page 37)*
– ANGLE (page 38)*
– VIRTUAL 3D SURROUND (page 39)
– VIDEO EQUALIZER (page 51)
– DIGITAL VIDEO ENHANCER (page 52)
* DVD only
Notes
• The player can store the settings of up to 300 discs. When you
store the setting of disc number 301, the first disc setting is
canceled.
• Depending on the DVD, the information stored in the disc
takes priority over the Playback Memory settings and the
function does not work.
• Do not turn off the player by pressing !. Doing so may cancel
the settings. When you turn off the player, press x first to stop
playback and then press ?/1 on the remote. After the power
indicator lights up in red and the player enters standby mode,
press ! on the player.
x TRACK SELECTION
Gives the sound track which contains the highest number
of channels priority when you play a DVD on which
multiple audio formats (PCM, DTS or Dolby Digital
format) are recorded.
• OFF : No priority given.
• AUTO : Priority given.
Notes
• When you set this item to "AUTO," the language may change
depending on the "AUDIO" settings in "LANGUAGE SETUP."
The "TRACK SELECTION" setting has higher priority than the
"AUDIO" settings in "LANGUAGE SETUP" (page 59).
• If you set "DTS" in "AUDIO SETUP" to "D-PCM", the DTS
sound track is not played even if you set this item to "AUTO"
and the highest-numbered audio channel is recorded in DTS
format.
• If PCM, DTS and Dolby Digital sound tracks have the same
number of channels, the player selects PCM, DTS and Dolby
Digital sound tracks in this order.
• Depending on the DVD, the audio channel with priority may
be predetermined. In this case, you cannot give priority to the
Q Q
DTS or Dolby Digital format by selecting "AUTO."
3 6 7 1 3
x DTS
Selects the DTS signals to be output via the DIGITAL OUT
OPTICAL and COAXIAL connectors.
• D-PCM: when the player is connected to an audio
component lacking a built-in DTS decoder. If you play
DTS sound tracks, the player outputs stereo signals via
the DIGITAL OUT OPTICAL and COAXIAL
connectors.
• DTS: when the player is connected to an audio
component having a built-in DTS decoder.
If the player is connected to an audio component
lacking a built-in DTS decoder, do not set this.
Otherwise, when you play the DTS sound track, a loud
noise (or no sound) will come out from the speakers,
affecting your ears or causing the speakers to be
damaged.
x 48kHz/96kHz PCM (DVD only)
Selects the sampling frequency of the audio signal to be
output via the DIGITAL OUT OPTICAL and COAXIAL
connectors.
• 48kHz/16bit: The audio signals of DVDs are always
converted to 48 kHz/16 bit.
• 96kHz/24bit: All types of signals including 96 kHz/24
bit are output in their original format. However, if the
signal is encrypted for copyright protection purposes,
the signal is only output as 48 kHz/16 bit.
Notes
• If you select "96kHz/24bit" when a receiver (amplifier) which
cannot accept 96 kHz is connected to the player, no sound or a
loud noise will come out from the speakers.
• Even if you set "48kHz/96kHz PCM" in "AUDIO SETUP" to
"96kHz/24bit," the sampling frequency is converted to 48
kHz/16 bit when a VIRTUAL 3D SURROUND mode is
selected.
• The analog audio signals from the AUDIO OUT connectors are
not affected by this setting and keep their original sampling
frequency level.
.
1-16
9 4 2 8
Settings for the Sound
(AUDIO SETUP)
"AUDIO SETUP" allows you to set the sound according
to the playback conditions.
The default settings are underlined.
Select "AUDIO SETUP" in the setup display.
AUDIO SETUP
AUDIO ATT:
AUDIO DRC:
CENTER SPEAKER EQ:
DOWNMIX:
DOLBY SURROUND
DIGITAL OUT:
DOLBY DIGITAL:
DTS:
48kHz/96kHz PCM:
To set, press , then ENTER
To quit, press DISPLAY .
x AUDIO ATT (attenuation)
If the playback sound is distorted, set this item to "ON."
The player reduces the audio output level.
Selects the setting of the output from the AUDIO OUT
(1, 2) connectors according to the audio equipment to be
connected.
• OFF: turns off the audio attenuation. Normally select
this position.
• ON: reduces the audio output level so that no sound
distortion occurs. Select this when the playback sound
from the built-in TV speakers is distorted.
Note
The setting does not affect the output from the DIGITAL OUT
OPTICAL and COAXIAL connectors.
x AUDIO DRC (Dynamic Range Control)
(DVD only)
Makes the sound clear when the volume is turned down
when playing a DVD. This function works only when
you play a DVD which has the AUDIO DRC function.
This affects the output from the DIGITAL OUT connectors
only when "DOLBY DIGITAL" is set to "D-PCM" and
"DTS" to "D-PCM" in "DIGITAL OUT."
• STANDARD: Normally select this position.
• TV MODE: makes the low sounds clear even if you turn
the volume down. It is especially recommended when
you listen to the sound using the speakers of the TV.
• WIDE RANGE: It gives you the feeling of being at a live
performance. This function only works when you are
playing a Dolby Digital disc and is more effective when
you connect 6 speakers using the 5.1 channel
connectors. When you use high quality speakers, it is
even more effective.
Note
1 5 0 5 8 2 9 9 4
When you play DVDs without the AUDIO DRC function, there
may be no effect on the sound.

Settings for the Speakers

(SPEAKER SETUP)

To obtain the best possible surround sound when you use
the 5.1CH OUTPUT connectors, use the SPEAKER SETUP
display to first specify the size of the speakers you have
connected and their distance from your listening position.
Then set the balance and level. Use the test tone to adjust
the volume of the speakers to the same level.
For speaker hookup instructions, see page 12.
The default settings are underlined.
Select "SPEAKER SETUP" in the setup display.
SPEAKER SETUP
SIZE:
DISTANCE:
BALANCE:
LEVEL:
TEST TONE: OFF
FRONT:
CENTER:
LARGE ( REAR )
REAR:
SUBWOOFER:
To set, press , then
ENTER
To quit, press . .
SETUP DISPLAY
x SIZE
Selects the size of the speakers to be connected.
• FRONT
— LARGE: Normally select this.
— SMALL: When the sound cracks or the surround
sound effects are difficult to hear, select this. This
activates the Dolby Digital bass redirection circuitry
and outputs the bass frequencies of the speaker from
the subwoofer.
• CENTER
— NONE: If you do not connect a center speaker, select
this.
— LARGE: Normally select this.
— SMALL: When the sound cracks, select this. This
activates the Dolby Digital bass redirection circuitry
and outputs the bass frequencies of the center
speaker from other speakers .
• REAR
— NONE: If you do not connect rear speakers, select
m
this.
— LARGE (REAR/SIDE): Normally select either of
these according to the rear speaker's position*.
co
— SMALL (REAR/SIDE): When the sound cracks or the
surround sound effects are difficult to hear, select
either of these according to the rear speaker's
position*. This activates the Dolby Digital bass
redirection circuitry and outputs the bass frequencies
of the rear speaker from other speakers .
9 9
OFF
STANDARD
FLAT
ON
D-PCM
D-PCM
48kHz/16bit
.
2 8 9 9
65
LARGE
LARGE
YES
.
67