GME TX3600 Series Instruction Manual page 15

2. Rotate the Channel Selector knob to step through the
available Selcall memories. The selected selcall memory
number is displayed in the channel display area.
MC522BC- Press the
available selcall memories. The selected selcall memory
number is displayed in the channel display area.
3. If there are Alpha labels associated with the Selcall Idents,
you can switch between Alpha and Numeric display
modes by briefly pressing the Volume knob. 'ALPhA' or
'NUMEr' will appear briefly in the selcall display area to
indicate the selected mode.
MC522BC- If there are Alpha labels associated with the
Selcall Idents, you can switch between Alpha and Numeric
display modes by briefly pressing the B key. 'ALPhA' or
'NUMEr' will appear briefly in the selcall display area to
indicate the selected mode.
Selcall memory location
Selcall Ident or label
MC522BC OPTION
Selcall memory location
To transmit the selected Selcall Ident while in the Call To
mode, press and hold the CaLL key for a few seconds until
a beep is heard. The 'TX' indicator will appear on the display
and the selected selcall will be transmitted. The radio will
then return to normal operation.
Note: of the 40 available memory locations, 1 thru 38
are available for user defined or preprogrammed Selcall
memories. Location 39 contains the Pager Ident. If the
Pager feature is disabled, then this memory location is also
available as a user defined memory. Location 40 is reserved
for the 'last-sent' selcall Ident and is not editable.
Editing the Preprogrammed Call To Selcall
Memories
If your retailer has enabled Selcall Memory Editing on your
radio, you can program and store your own Selcall Ident
memories and associated Alpha labels as follows.
Tip: The memory is programmed in two stages with the
Numeric Ident being programmed first, followed by the
T X 3 6 0 0 S ErI ES
and keys to step through the
Selcall Ident or label
INSTrUCTIoN MA NUA L
Alpha label if required. Each memory should be programmed
in one continuous process. If no user input is detected for
20 seconds, the radio will return to normal mode and you
will have to begin again.
1. Briefly press the CaLL key. 'Call To' will appear on the
display, and the Selcall Ident for memory location 1 will
be displayed. If the radio is in Alpha mode, the radio may
display a label representing the Ident instead of the Ident
number itself. If there is no label programmed, the selcall
display area will be blank when in Alpha mode.
2. Rotate the Channel Selector knob to select the
required Selcall memory. The selected selcall memory
number is displayed in the channel display area.
MC522BC-
Press the
required Selcall memory. The selected selcall memory
number is displayed in the channel display area.
3. Briefly press the Volume knob to select the Numeric
mode. 'NUMEr' will appear briefly in the Selcall display
area when Numeric mode is selected.
MC522BC- Briefly press the B key to select the Numeric
mode. 'NUMEr' will appear briefly in the Selcall display
area when Numeric mode is selected.
Alpha Mode
MC522BC OPTION
Alpha Mode
4 To enter the EDIT mode, press and hold the Channel
Selector knob until a beep is heard. 'EDIT' will appear
briefly in the selcall display area and the right hand selcall
digit will begin flashing.
MC522BC- To enter the EDIT mode, press and hold the
A key until a beep is heard. 'EDIT' will appear briefly in
the selcall display area and the right hand selcall digit
will begin flashing.
5. rotate the Channel Selector knob to alter the flashing
digit. When the correct digit is displayed, briefly press
the Channel Selector knob to move to the next digit.
Continue the process until the required Selcall Ident
is displayed.
MC522BC- Press the
digit. When the correct digit is displayed, briefly press the
and keys to select the
Numeric Mode
Numeric Mode
and keys to alter the flashing
PAgE 15