Bosch PSM VENTARO 1400 Operating Instructions Manual page 16

OBJ_BUCH-39-003.book Page 16 Tuesday, November 28, 2006 11:31 AM
Noise/Vibration Information
Measured values determined according to EN 60745.
Typically the A-weighted sound pressure level of the
machine is 80 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 85 dB(A).
Wear hearing protection!
Overall vibrational value (vector sum of three direc-
tions) determined according to EN 60745:
Vibrational emission value a
2
K = 1.5 m/s .
The vibration emission level given in
WARNING
this information sheet has been meas-
ured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with
another.
The vibration emission level will vary because of the
ways in which a power tool can be used and may
increase above the level given in this information sheet.
This could lead to a significant underestimate of expo-
sure when the tool is used regularly in such a way.
Note: To be accurate, an estimation of the level of
exposure to vibration experienced during a given period
of work should also take into account the times when
the tool is switched off and when it is running but not
actually doing the job. This may significantly reduce the
exposure level over the total working period.
Declaration of Conformity
Multi Sander
We declare under our sole responsibility that this prod-
uct is in conformity with the following standards or
standardization documents: EN 792 according to the
provision 98/37/EC.
Vacuum cleaner
We declare under our sole responsibility that this prod-
uct is in conformity with the standards or standardiza-
tion documents:
EN 60335 according to the provisions of the directives
73/23/EG, 89/336/EEC.
05
Dr. Egbert Schneider Dr. Eckerhard Strötgen
Senior Vice President Head of Product
Engineering Certification
31.10.2006, Robert Bosch GmbH, Power Tools Division
D-70145 Leinfelden-Echterdingen
16 | English
Assembly
Inserting/Replacing a Dust Bag
(see figures B and C)
Unlatch both latches 5 and fold up the vacuum lid 14.
Open the closing flap 16 and guide the dust bag 18
from the top into the guide 17 as shown in the figure.
Shut the closing flap 16 again until it can be heard to
2
= 7.0 m/s , uncertainty
h engage.
When removing a full dust bag, ensure that the dust
bag enclosure is clean. If required, clean the enclosure
with a moist cloth or a brush.
Fold down and lock the vacuum lid 14 with the
latches 5.
Operating Modes of the Vacuum
Cleaner (see figure A)
Vacuuming Function
The vacuum cleaner 4 can be used to vacuum dry, non-
hazardous materials. The supplied multi sander 1 can
be used in this operating mode.
For vacuum cleaning, the dust bag must be inserted.
For this, see chapter "Inserting/Replacing a Dust Bag".
Align the arrows on the vacuum hose 3 and the vacuum
hose connection 8 and insert the vacuum hose into the
vacuum hose connection. You will hear a distinct "click"
when the vacuum hose locks in the vacuum hose con-
nection.
You can connect the multi sander 1 or any of the acces-
sories mentioned on the accessories page to the vac-
uum hose 3.
Blower Function
The vacuum cleaner 4 can easily be converted to a
blower in no time at all.
Remove the closing cover with blower filter 12 from the
holder 10 and insert the adapter for the blower connec-
tion 11 in its place.
Align the arrows of the vacuum hose 3 and the adapter
for the blower connection 11 and insert the vacuum
hose into the adapter. You will hear a distinct "click"
when the vacuum hose locks in the adapter.
Removing the Vacuum Hose
To remove the vacuum hose 3, rotate the hose a little
and pull it off.
Before using the vacuum cleaner, always
remove the plug cap 9. Pay attention that the
bypass valve 15 is never restricted or blocked.
The motor of the vacuum cleaner can overheat und
become damaged.
Do not point the blower jet at persons or ani-
mals. The blown-out air is warm.
1 609 929 J33 • 28.11.06