Sony HCD-FL7D Service Manual page 31

QQ
3 7 63 1515 0
2-1-3. Disc Type CD
It sets up so that it may judge as a disc type of specification of the
disc with which the set was inserted.
[1]
: CD disc (normal speed, 12 cm)
[2]
: CD disc (double speed, 12 cm)
[3]
: CD disc (normal speed, 8 cm)
[4]
: CD disc (double speed, 8 cm)
[5]
: CD-RW disc (normal speed, 12 cm)
[6]
: CD-RW disc (double speed, 12 cm)
[7]
: CD-RW disc (normal speed, 8 cm)
[8]
: CD-RW disc (double speed, 8 cm)
2-1-4. Disc Type Hybrid
It sets up so that it may judge as a disc type of specification of the
disc with which the set was inserted.
[1]
: SACD Hybrid disc (SACD layer, 12 cm)
[2]
: SACD Hybrid disc (CD layer, normal speed, 12 cm)
[3]
: SACD Hybrid disc (CD layer, double speed, 12 cm)
[4]
: SACD Hybrid disc (SACD layer, 8 cm)
[5]
: SACD Hybrid disc (CD layer, normal speed, 8 cm)
[6]
: SACD Hybrid disc (CD layer, double speed, 8 cm)
2-2. Servo Control
Note: Be sure to perform the disc type setup before performing this item.
1.LD
2.Focus
3.SPDL
4.CLVA
5.Trk.
TE
L 13942296513
6.Sled
7.Fcs.Srch
8.Fcs.OppL
0.All Servo Off
On this screen, the servo on/off control necessary for replay is
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system
is faulty or RF is not present. In such a case, do not operate CLVA.
[1]
LD
[2]
Focus
[3]
SPDL
[4]
CLVA
[5]
Trk.
[6]
Sled
[7]
FCS. Srch : Turn on/off the focus search.
[8]
FCS. OppL : Turn on/off the focus search to another
[10/0]
[R]
Sled FWD (right cursor) :
[L]
Sled REV (left cursor) : Move the sled reverse.
www
[U]
Sled FWD (up cursor) : Reset the sled.
[D]
Sled REV (down cursor) :
.
http://www.xiaoyu163.com
Servo Control
off R.Sled FWD
off L.Sled REV
off U.Sled Reset
off D.Sled Limit
off
off
off
off
Exit: RETURN
: Turn on/off the laser.
: Search the focus and turn on the focus.
: Turn on/off the spindle.
: Turn on/off normal servo of spindle servo.
: Turn on/off the tracking servo.
: Turn on/off the sled servo.
(oposite) layer of designated layer in Disc
Type setting. (dual layer disc only)
: All servo off.
Move the sled forward.
Limit in the sled.
x ao
y
i
http://www.xiaoyu163.com
8
2-3. Track/Layer Jump
1.
2.
3.500Tj Fine
4.500Tj Fine
5.10kTj Dirc
6.10kTj Dirc
7.20kTj Dirc
8.20kTj Dirc
0. All Servo Off
On this screen, track jump, etc. can be performed. Only for the
DVD dual layer disc, the focus jump and layer jump are displayed
in the right field
[1]
1Tj FWD
[2]
1Tj REV
[3]
500Tj FWD : 500 track jump (fine search)forward.
[4]
500Tj REV : 500 track jump (fine search) reverse.
[5]
10kTj FWD : 10k track jump (direct search) forward.
[6]
10kTj REV : 10k track jump (direct search) reverse.
[7]
20kTj FWD : 20k track jump (direct search) forward.
[8]
20kTj REV : 20k track jump (direct search) reverse.
p LjL0 t L1 : Layer jamp L0 t L1
P LjL1 t L0 : Layer jamp L1 t L0
O FjL0 t L1 : Focus jamp L0 t L1
Q Q
3 6 7 1 3
o FjL1 t L0 : Focus jamp L1 t L0
[10/0]
2-4. Non EEPROM Write Adjust
1. Focus Offset
2. Focus Gain
3. Trk.
4. Trk.
5. Trk.
6. EQ
0.All Servo Off
On this screen, each item can be adjusted automatically. Select the
desired number
value is not stored in the EEPROM.
[1]
Focus Offset : Adjusts focus offset.
[2]
Focus Gain : Adjusts focus gain.
[3]
TRK. Offset : Adjusts tracking offset of the RF amp
[4]
TRK. Offset : Adjusts tracking offset of the DSP (IC401)
[5]
TRK. Gain : Adjusts track gain.
[6]
u163 EQ Boost
[10/0]
.
2 9 9 4 2 8
Track/Layer Jump
1Tj FWD R.Lj L0>L1
1Tj REV L.Lj L1>L0
FWD U.Fj L0>L1
REV D.Fj L1>L0
FWD
REV
FWD
REV
Exit: RETURN
: 1 track jump forward.
: 1 track jump reverse.
1 5 0 5 8 2 9 9 4
: All servo off.
Non EEPROM Write Adjust
Offset Coarse
Offset Fine
Gain
Boost
Exit: RETURN
[1] [10/0]
to from the remote commander. This
(IC001) side.
m
side.
co : Adjusts amount of boost of equalizer.
: All servo off.
HCD-FL7D
9 9
2 8 9 9
31