LG LSRG309ST Service Manual page 43

WARNING
• Turn off the electrical supply and
gas supply going to the range.
• Replace all panels and parts before
operating.
• RECONNECT all grounding devices.
- Failure to do so can result in severe personal
injury, death or electrical shock.
CAUTION
• Be careful when you work on the
gas range handling the sheet metal
part.
- Sharp edge may be present and you can cut
yourself.
5. CONVERT THE OVEN BURNER ORIFICES
1) OVEN LOWER BURNER(BAKE)
a) Remove oven door, oven bottom, frame
guide, nozzle case and oven burner
assembly (See the page 3-10).
b) Remove the orifice spud from nozzle holder
using a 13/32" or 10mm wrench.
c) Install the LP orifce spud(D) to the nozzle
holder. To prevent leakage, make sure the
orifice spud is securely screwed into the
nozzle holder.
Clockwise to install Clockwise to install Clockwise to install Clockwise to install Clockwise to install
Clockwise to install Clockwise to install
Clockwise to install Clockwise to install Clockwise to install Clockwise to install Clockwise to install Clockwise to install
Clockwise to install Clockwise to install Clockwise to install Clockwise to install Clockwise to install
2) OVEN UPPER BURNER(BROIL)
1) Remove oven door and Broil burner
assembly. Then remove the wire cover
using a phillips head screwdriver (See the
page 3-11).
CONVERSION TO LP GAS
Counterclockwise Counterclockwise Counterclockwise Counterclockwise Counterclockwise
Counterclockwise Counterclockwise Counterclockwise Counterclockwise Counterclockwise Counterclockwise
Counterclockwise Counterclockwise
Counterclockwise Counterclockwise Counterclockwise Counterclockwise Counterclockwise
to remove to remove to remove
to remove to remove to remove to remove
to remove to remove to remove to remove to remove to remove
to remove to remove to remove to remove
to remove
2) Release the connector of the lgniter.
3) Remove the orifice spud from nozzle holder
using a 13/32" or 10mm wrench.
4) Install the LP orifce spud(C) to the nozzle
holder. To prevent leakage, make sure the
orifice spud is securely screwed into the
nozzle holder.
6. Turn on the Electrical and Gas Supply to
continue with flame adjustment.
7. ADJUSTING THE AIR SHUTTER
For bake burner, adjust the Air Shutter for LP
gas, loosen the Philips head screw and rotate the
shutter to the fully open position as shown Fig.1.
NOTE: When converting the unit back to natural
gas the bake burners air shutter should be also in
fully open position.
For broil burner, adjust the Air Shutter for LP gas,
loosen the Philips head screw and rotate the air
shutter until the opening appears to be 1/2
closed. (Refer to Fig.2).
NOTE: When converting the unit back to natural
gas the broil burners air shutter should be in fully
open position.
Screw
Air Shutfer
Fig.1
5-4
Counterclockwise Counterclockwise Counterclockwise
Counterclockwise Counterclockwise Counterclockwise Counterclockwise
Counterclockwise Counterclockwise Counterclockwise Counterclockwise
Counterclockwise Counterclockwise Counterclockwise Counterclockwise Counterclockwise Counterclockwise
Counterclockwise
to remove to remove to remove to remove to remove
to remove to remove to remove to remove to remove to remove
to remove to remove
to remove to remove to remove to remove to remove
Clockwise to install Clockwise to install Clockwise to install Clockwise to install Clockwise to install
Clockwise to install Clockwise to install Clockwise to install Clockwise to install Clockwise to install Clockwise to install
Clockwise to install Clockwise to install Clockwise to install Clockwise to install
Clockwise to install Clockwise to install Clockwise to install
Screw
Air Shutter
Counterclockwise Counterclockwise Counterclockwise
to 1/2 close position to 1/2 close position to 1/2 close position
Clockwise to
fully open position
Fig.2