Technical Data - EINHELL BG-PC 3735 Operating Instructions Manual

Anleitung BG_PC_3735_SPK1:_

4. Technical data

Engine displacement
Maximum engine capacity
Bar length
Cutter rail length
Chain pitch
Chain thickness
Idling speed
Maximum speed with cutting equipment
Tank capacity
Oil tank capacity
Anti-vibration function
Chain wheel teeth
Chain brake
Clutch
Automatic chain lubrication
Low-kickback chain
Net weight without chain and chain bar
Net weight (dry)
Fuel consumption (specific)
L sound pressure level
pA
L sound power level
WA
Vibration a (front handle)
hv
Vibration a (rear handle)
hv
Chain type
CARLTON (N1C-BL-52E SK B)
Bar type
OREGON (140SDEA041)/QIRUI (PO14-50SR)
Spark plug
5. Before starting the equipment
Important: Do not start the engine until the saw
is fully assembled.
Important: Wear protective gloves at all times
when handling the chain.
5.1 Fit the chain bar
To ensure that the bar and the chain are supplied
with oil, USE ONLY THE ORIGINAL BAR. The oiling
hole (Fig. 2/Item A) must be kept clear of dirt and any
build-up of residue.
1. Make sure the Chain brake lever is pulled back
into the DISENGAGED position (Fig. 3A)
16.03.2009 8:12 Uhr
2. Remove the two bar fastening nuts (B). Remove
the cover (Fig. 3B).
37.2 cm 3
Important: When assembling for the first time,
the material fitted to provide protection during
1.2 kW
transportation (Fig. 3C/Item 24) must be removed
32 cm
first.
14" (35 cm)
3. Using a screwdriver, run the adjustment screw
(3/8"), 10 mm
(D) COUNTERCLOCKWISE until the TANG (E)
(projecting prong) is to the end of its travel toward
(0.05"), 1.27 mm
the clutch drum and sprocket (Fig. 3B/3C).
3200 rpm
4. Fit the open end of the chain bar over the die bar
11000 rpm
pins (F) (Fig. 3C/3D).
310 ml
5.2 To install saw chain
210 ml
1. Spread chain out in a loop with cutting edges (A)
Yes
pointing CLOCKWISE around loop (Fig. 4A).
6 x 9.525 mm
2. Slip the chain around the sprocket (B) behind the
Yes
clutch (C). Make sure the links fit between the
sprocket teeth (Fig. 4B).
Yes
3. Guide the drive links into the groove (D) and
Yes
around the end of the bar (Fig. 4B).
Yes
4.55 kg
NOTE: The saw chain may droop slightly on the lower
part of bar. This is normal.
5 kg
560 g / kWh
4. Pull the chain bar forward until the chain is closely
100 dB(A)
seated. Make sure that all the drive links are in
112 dB(A)
the groove of the bar.
5. Fit the clutch cover and fasten it with 2 screws.
max. 5.46 m/s 2
Make sure that the pivot (Fig. 3C/Item E) fits into
max. 6.21 m/s 2
the chain bar (Fig. 3D/Item G). The chain must
OREGON (91PO53X)/
not slip off the bar when you do this. Tighten the
two nuts by hand and then follow the instructions
for adjusting the tension in ADJUSTING THE
CHAIN TENSION.
L8RTF
5.3 Saw chain tension adjustment
Proper tension of saw chain is extremely important
and must be checked before starting, as well as
during any cutting operation.
Taking the time to make needed adjustments to the
saw chain will result in improved cutting performance
and prolonged chain life.
Warning: Always wear heavy duty gloves when
handling saw chain or making saw chain adjustments.
1. Hold nose of guide bar up and turn adjustment
screw (D) CLOCKWISE to increase chain
tension. Turning screw COUNTERCLOCKWISE
will decrease amount of tension on chain. Ensure
the chain fits snugly all the way around the guide
bar (Fig. 5).
2. After making adjustment, and while still holding
nose of bar in the uppermost position, tighten the
bar retaining nuts securely. Chain has proper
Seite 21
GB
21