Anleitung_BG_PC_5045_SPK1:_ 26.10.2010 9:41 Uhr Seite 19 Table of contents: 1. Safety regulations 2. Layout 3. Intended use 4. Technical data 5. Before starting the equipment 6. Operation 7. Cleaning, maintenance, storage and ordering of spare parts 8. Disposal and recycling 9.
Page 9
Anleitung_BG_PC_5045_SPK1:_ 26.10.2010 9:41 Uhr Seite 20...
Anleitung_BG_PC_5045_SPK1:_ 26.10.2010 9:41 Uhr Seite 21 4. Technical data 5. Before starting the equipment Important: Do not start the engine until the saw is fully assembled. Maximum engine capacity 2.2 kW Important: Wear protective gloves at all times when handling the chain. l i a ”...
Page 11
Anleitung_BG_PC_5045_SPK1:_ 26.10.2010 9:41 Uhr Seite 22 5.3 Saw chain tension adjustment Warning: The purpose of the chain brake is to Proper tension of saw chain is extremely important reduce the possibility of injury due to kickback; and must be checked before starting, as well as however, it cannot provide the intended measure of during any cutting operation.
Anleitung_BG_PC_5045_SPK1:_ 26.10.2010 9:41 Uhr Seite 23 Recommended fuels 6.2 Restarting a warm engine Some conventional petrols are being blended with 1. Make sure the switch is in the ON position. oxygenates such as alcohol or an ether compound to 2. Pull the starter rope rapidly 6 times. The engine meet clean air standards.
Anleitung_BG_PC_5045_SPK1:_ 26.10.2010 9:41 Uhr Seite 24 always stand on the uphill side. Warning: Never walk in front of a tree that has 1. Log supported along entire length: Cut from been notched. Make the felling cut (D) from the other top (overbuck), being careful to avoid cutting into side of the tree and 1.5 - 2.0 inches (3-5 cm) above the ground (Fig.
Page 14
Anleitung_BG_PC_5045_SPK1:_ 26.10.2010 9:41 Uhr Seite 25 7.2 Maintenance 4. Insert the air filter. Fit the cover for the engine/air filter. Make sure that the cover fits perfectly when Warning: All maintenance work on the chainsaw you do so. Tighten the fastening screw for the apart from the work described in this manual may cover.
Page 15
Anleitung_BG_PC_5045_SPK1:_ 26.10.2010 9:41 Uhr Seite 26 7.2.6 Chain bar maintenance Warning: Always wear protective gloves during Regular lubrication of the chain bar (guide rail for the maintenance operations. Do not carry out chain and teeth) is essential. The chain bar needs the maintenance when the engine is hot.
Page 16
Anleitung_BG_PC_5045_SPK1:_ 26.10.2010 9:41 Uhr Seite 27 7.2.7 Chain maintenance Chain lubrication Always make sure the automatic oiler system is Chain sharpening working properly. Keep the oil tank filled with Chain, Chain sharpening requires special tools to ensure Bar and Sprocket Oil. that cutters are sharpened at the correct angle and Adequate lubrication of the bar and chain during depth.
Identification number of the machine Replacement part number of the part required For our latest prices and information please go to www.einhell.com.au 8. Disposal and recycling The unit is supplied in packaging to prevent its being damaged in transit. This packaging is raw material and can therefore be reused or can be returned to the raw material system.
Anleitung_BG_PC_5045_SPK1:_ 26.10.2010 9:41 Uhr Seite 29 9. Troubleshooting guide Problem Probable cause Corrective Action Unit wonʼt start or starts but will not Incorrect starting procedures. Follow instructions in the User run. Manual. Incorrect carburetor mixture Have carburetor adjusted by an adjustment setting.
Page 19
The Einhell Express Guarantee is valid for a period of 2 years starting from the purchase date of the product. Claims made under the Einhell Express Guarantee should be submitted before the end of this guarantee period and within two weeks of the defect being noticed.
Need help?
Do you have a question about the BG-PC 5045 and is the answer not in the manual?
Questions and answers