Technical Data; Before Starting The Equipment - EINHELL BG-PC 2245 Manual

Anleitung_BG_PC_2245_SPK1:_

4. Technical data

Engine displacement
Maximum engine capacity
Bar length
Cutter rail length
Chain pitch
Chain thickness
Idling speed
Maximum speed with cutting equipment
Tank capacity
Oil tank capacity
Anti-vibration function
Chain wheel teeth
Chain brake
Clutch
Automatic chain lubrication
Low-kickback chain
Net weight without chain and chain bar
Net weight (dry)
Fuel consumption (specific)
LPA sound pressure level (ISO 22868)
KPA uncertainty
LWA sound power level measured
(ISO 22868)
KWA uncertainty
LWA sound power level guaranteed
(ISO 2000/14/EC)
Ahv vibration (front handle)
(ISO 22867)
Khv uncertainty
Ahv vibration (rear handle)
(ISO 22867)
K uncertainty
hv
Chain type
Bar type
Spark plug
26.03.2012 10:34 Uhr

5. Before starting the equipment

49.3 cm 3
Important: Do not start the engine until the saw
is fully assembled.
2.2 kW
44 cm
Important: Wear protective gloves at all times
when handling the chain.
18" (45 cm)
(0.325"), 8.255 mm
5.1 Fit the chain bar
(0.058"), 1.47 mm
To ensure that the bar and the chain are supplied
with oil, USE ONLY THE ORIGINAL BAR. The oiling
3200 rpm
hole (Fig. 2/Item A) must be kept clear of dirt and any
11000 rpm
build-up of residue.
550 ml
1. Make sure the Chain brake lever is pulled back
into the DISENGAGED position (Fig. 3A)
260 ml
2. Remove the two bar fastening nuts (B). Remove
Yes
the cover (Fig. 3B).
7 x 8.255 mm
3. Using a screwdriver, run the adjustment screw
(D) COUNTERCLOCKWISE until the TANG (E)
Yes
(projecting prong) is to the end of its travel toward
Yes
the clutch drum and sprocket (Fig. 3B/3C).
Yes 4. Fit the open end of the chain bar over the die bar
pins (F) (Fig. 3C/3D).
Yes
5.4 kg
5.2 To install saw chain
1. Spread chain out in a loop with cutting edges (A)
6.7 kg
pointing CLOCKWISE around loop (Fig. 4A).
560 g / kWh
2. Slip the chain around the sprocket (B) behind the
101 dB(A)
clutch (C). Make sure the links fit between the
sprocket teeth (Fig. 4B).
2.5 dB(A)
3. Guide the drive links into the groove (D) and
around the end of the bar (Fig. 4B).
110 dB(A)
NOTE: The saw chain may droop slightly on the lower
2.5 dB(A)
part of bar. This is normal.
114 dB(A)
4. Pull the chain bar forward until the chain is closely
seated. Make sure that all the drive links are in
the groove of the bar.
max. 6.6 m/s 2
5. Fit the coupling cover and fasten it with 2 screws.
1.5 m/s 2
The chain must not slip off the bar when you do
this. Make sure that the pin (Fig. 3C/Item E) fits
into the hole in the chain bar (Fig. 3D/Item G).
max. 6.91 m/s 2
Tighten the two nuts by hand and then follow the
instructions for adjusting the tension in the
1.5 m/s 2
section ADJUSTING THE CHAIN TENSION..
Oregon 21BPX072X
Oregon 188PXBK095
L8RTF
Seite 21
GB
21