The reader should consult National Instruments if errors are suspected. In no event shall National Instruments be liable for any damages arising out of or related to this document or the information contained in it.
Page 4
These classes are known as Class A (for use in industrial-commercial locations only) or Class B (for use in residential or commercial locations). All National Instruments (NI) products are FCC Class A products. Depending on where it is operated, this Class A product could be subject to restrictions in the FCC rules. (In Canada, the Department of Communications (DOC), of Industry Canada, regulates wireless interference in much the same way.) Digital...
Page 5
Conventions This manual provides information on the installation and use of an NI CardBus-8310-to-PXI Expansion system. The following conventions are used in this manual: » The » symbol leads you through nested menu items and dialog box options to a final action. The sequence File»Page Setup»Options directs you to pull down the File menu, select the Page Setup item, and select Options from the last dialog box.
Page 7
Storage Environment... B-2 Appendix C Troubleshooting NI PXI-CardBus-8310 Cards Contacting Technical Support ... C-1 Troubleshooting... C-2 Error Code (Yellow Exclamation Mark) in Device Manager ... C-8 Appendix D Technical Support and Professional Services Index NI CardBus-8310-to-PXI Expansion User Manual viii ni.com...
It also contains recommended steps to be taken while preparing to install the NI CardBus-8310 and NI PXI-8310 modules. Functional Overview The National Instruments CardBus-8310-to-PXI interface kit provides laptop computers direct control of PXI systems. The CardBus-to-PXI link is transparent to software applications and drivers, thereby providing you the ability to use high-performance laptop computers to control PXI systems.
33 MHz, while the StarFabric link can simultaneously transmit and receive at 2.5 Gbps. A standard link is made up of four aggregated 622 Mbps LVDS differential pairs in each direction. NI CardBus-8310-to-PXI Expansion User Manual RJ-45 RJ-45 Connector...
The NI CardBus-8310-to-PXI is available with cables of various lengths. Table 1-1 shows the cables that are available from National Instruments. Cable Length (meters) Before Installation Before installing the NI CardBus-8310-to-PXI expansion system you should perform the following steps.
You can take the following steps to prevent damage from electrostatic discharge (ESD): • • NI CardBus-8310-to-PXI Expansion User Manual Avoid sharp bends or folds in the cables. Provide enough slack to allow easy device placement. Avoid things that might cause scuffing and abrasion damage to the cables.
All LEDs blinking—Communication has been lost. At some point the transmitter and receiver were linked, however now they are longer synchronized. The link needs to be re-established before data can be transmitted again. Chapter 1 Introduction NI CardBus-8310-to-PXI Expansion User Manual...
Page 13
Note can be used to isolate the faulty cable. If replacing the cable does not resolve the issue, there may be a problem with the StarGen bridge. In that case, contact National Instruments with the information described in the Troubleshooting NI PXI-CardBus-8310 NI CardBus-8310-to-PXI Expansion User Manual Table 1-3.
Hardware and Software Installation Windows 2000/XP (Without XP Service Pack 2) Windows XP (With Service Pack 2) NI CardBus-8310-to-PXI Expansion User Manual If you do not have your system configured to allow autorun CDs, you must run to install the NI CardBus-8310 driver.
Page 17
Figure. 2-1. Click Next. The dialog box shown in Figure 2-3 will appear. Figure 2-3. Reboot Dialog Box Choose No and click Finish. Manually shut down your computer. Chapter 2 Hardware and Software Installation NI CardBus-8310-to-PXI Expansion User Manual...
PXI card that is having a problem to a different slot, or reordering your cards in their slots, may alleviate issues. Attach the PXI Expansion Cables NI CardBus-8310-to-PXI Expansion User Manual section of Chapter 1. Carefully position the PXI chassis so that the supplied cables will conveniently reach from the connector of the NI CardBus-8310 card to the connectors on the NI PXI-8310.
CardBus slot. Gently push the card until it is seated firmly. For more information on using CardBus cards, refer to your host computer’s user manual. Chapter 2 Hardware and Software Installation NI CardBus-8310-to-PXI Expansion User Manual...
Page 20
Hardware and Software Installation Figure 2-4. Found New Hardware Wizard Dialog Box (Windows 2000/XP SP2 Only) NI CardBus-8310-to-PXI Expansion User Manual Make sure your CAT5-e cables are connected correctly, then turn on the PXI chassis, and plug the NI CardBus-8310 card into the laptop.
Page 21
Figure 2-5. Software Installation Options Choose automatic installation and click Next. Figure 2-6. Installation Wizard Completion Dialog Box Once the StarGen PCI to PCI bridge installation is complete, click Finish. Chapter 2 Hardware and Software Installation NI CardBus-8310-to-PXI Expansion User Manual...
PXI chassis. In Figure 2-7, a PXI-GPIB card has been installed in a PXI chassis. NI CardBus-8310-to-PXI Expansion User Manual The Found New Hardware Wizard dialog box will appear again, and will find another PCI to PCI bridge, because there are two bridge chips.
Figure 2-9. The system will support daisy-chaining, but only to a certain depth of PCI bus segments. Systems connected in a Star configuration will also exhibit lower latency. NI CardBus-8310-to-PXI Expansion User Manual section of Chapter 1. Cards, for more information.
Page 27
Appendix A PCIScope The data can be stored as a requested to email this file to configuration problems. NI CardBus-8310-to-PXI Expansion User Manual Figure A-1. Example of PCIScope Interface file on your computer. You may be *.bpd support@ni.com if you are experiencing...
5 V ... 0 A Typical 3.3 V ... 0.15 A 5 V ... 1.5 A Maximum 3.3 V ... 0.40 A 5 V ... 1.7 A Input ... Up to 50 MB/s Output ... Up to 10 MB/s NI CardBus-8310-to-PXI Expansion User Manual...
For UL and other safety certifications, refer to the product label, or refer to the Document of Conformity, which has been included as a digital document on your driver CD. NI CardBus-8310-to-PXI Expansion User Manual CardBus-8310...0 to 40 °C PXI-8310 ...0 to 55 °C...
While this appendix contains a number of troubleshooting tips for resolving issues that may be experienced with NI CardBus-8310 cards, extreme cases may require you to contact National Instruments Technical Support. You can find that contact information in the Services You must be ready to give the following information prior to troubleshooting the system.
• Issue: The LEDs are flashing on the NI PXI-8310 card. • NI CardBus-8310-to-PXI Expansion User Manual No LEDs are lit on the NI PXI-8310 card. The LEDs are flashing on the NI PXI-8310 card. One or more LEDs are not lit on the NI PXI-8310 card.
Page 33
Figure C-1. Figure C-1. Devices by Connection Menu in Device Manager Remove the CardBus card from the PCMCIA slot. Install the NI CardBus Driver 1.0 from the provided driver CD. Troubleshooting NI PXI-CardBus-8310 Cards NI CardBus-8310-to-PXI Expansion User Manual...
Page 34
Issue: The host computer is unable to detect the third party PXI card in Windows Device Manager. • • NI CardBus-8310-to-PXI Expansion User Manual If the LEDs are flashing on the NI PXI-8310 card: – Try ejecting and reinserting the CardBus card.
Page 35
Devices by connection, there should be no errors. At this point, power down and begin adding PXI cards one by one, powering up to check that there are no errors in Device Manager after installing each card. This can isolate problematic hardware/software. Troubleshooting NI PXI-CardBus-8310 Cards NI CardBus-8310-to-PXI Expansion User Manual...
Page 36
• Issue: The host computer is blue-screening/frozen during reboot after installing the NI CardBus-8310 driver. NI CardBus-8310-to-PXI Expansion User Manual If any other hardware or software has been added recently: – Remove the recently installed program or hardware, and re-test the system.
Page 37
If the problem occurs consistently, please contact National Instruments for technical support. Issue: The application or program failed to communicate with the PXI device card during an operation. • • • Note You may want to check the manufacturer’s web site to see if there are any installation/driver updates for the device.
This usually means the memory, I/O, or Prefetch required by the card is more than what has been allocated by the NI driver. Right-click on the NI CardBus-8310-to-PXI Expansion User Manual • If another card that has worked in the past is available, try it in the same slot.
Page 41
Worldwide Offices section of office Web sites, which provide up-to-date contact information, support phone numbers, email addresses, and current events. NI CardBus-8310-to-PXI Expansion User Manual Declaration of Conformity (DoC)—A DoC is our claim of compliance with the Council of the European Communities using the manufacturer’s declaration of conformity.
Page 42
C-1 uninstalling the CardBus driver, 2-10 verification, 2-8 instrument drivers (NI resources), D-1 kit components, 1-4 KnowledgeBase, D-1 latencies Measurement and Automation Explorer (MAX), 2-11 system boot, 2-11 Measurement and Automation Explorer (MAX), 2-11 NI CardBus-8310-to-PXI Expansion User Manual...