Table of Contents
Advertisement
Optional Enhanced Weather
Protection (EWP) Available*
Note: This is a E-1600A-IP board (PCB) only kit. This kit can be
used to convert any Viking E-10A or E-30 analog phone to a VoIP
version. The kit can also be used to replace a damaged board in
the field.
Shipping Weight: .45 kg (1 lb)
Connections: (1) RJ45 10/100 Base-T, (3) optional gel-filled butt
connectors, (10) additional gel-filled butt connectors included with
EWP version only.
3.50 (3.58 EWP)
(2) 0.156
diameter
type 2
mounting
holes
Optional 2 Amp Relay
Output Contacts Connector
Connect to doorstrike,
mag lock, gate controller, etc.
Gray (N.C.)
Blue (COM)
Yellow (N.O.)
** Note: These two red wires are only
used on units with an Info button. When
installing on a single button unit, cut off
these two red wires and discard.
• IBM compatible personal computer with:
Windows 2000 (service pack 4 or higher)
Windows XP (service pack 2 or higher)
Windows Vista (SP2 or newer), 32 or 64 bit versions
Windows 7
Windows 8
A CD is included with each E-10/20/30-IP VoIP Entry phone. The CD contains the application "Viking VoIP Phone Pro-
gramming" used to program the unit using a PC running Windows 2000, XP, Vista, Windows 7, or Windows 8 (see System
Requirements above). The PC must be connected to the same LAN as the E-10/20/30-IP VoIP phone. Install the application
on your PC by placing the CD into your PC's drive. Click "I Accept" on the bottom of the first screen, then select "Viking
VoIP Phone Programming" and click the "Install" button. Follow the directions on the screen. If you are reinstalling the
Viking VoIP Phone Programming software you must uninstall the original version first via "Add and Remove Programs".
To start the Viking VoIP Phone Programming application, click on the Viking VoIP Phone Programming icon on your desk
top. The Main screen will appear, allowing the user to program any E-10/20/30-IP phone connected to that LAN.
A. Configuring the E-10/20/30-IP Network Settings
Open the "Viking VoIP Phone Programming" software on a windows PC that is connected to the
Step 1.
same LAN as the E-10/20/30-IP phone to be programmed.
The window in the upper left corner of the menu will show you each E-10/20/30-IP phone that is con-
Step 2.
nected to that LAN. Select the unit with the same MAC address shown on the label located on the
top of the Ethernet connector on the E-10/20/30-IP phone.
Click the "Connect" button. If a pop up window appears, enter the unit's security code (factory set to
Step 3.
845464) then click the "OK" button.
Step 4. The program will then read and display the E-10/20/30-IP phone's IP and programming settings.
After adjusting the IP and phones settings, click the "Write" button under each column of settings
Step 5.
to send the programming commands to the connected unit.
E-1600-53A-IP
3.20
0.15 (0.19 EWP)
1.5
0.63
(0.67
EWP
8
1 10
1
Connector and Wires
from Existing Standard
E-30 Analog
Entry Phone
Black
Red
Black
Black
Red**
Red**
White
White
Black
Red
PC Requirements
PC Programming
*Optional Enhanced Weather Protection (EWP): The op-
tional EWP products feature foam rubber gaskets and boots,
sealed connections, gel-filled butt connectors, as well as ure-
thane or thermal plastic potted circuit boards. See DOD# 859.
Replacing Analog E-10A, E-10A-EWP or E-30-EWP Circuit
Boards:
Step 1.
Step 2.
Step 3.
2.0
Step 4.
(2.04
EWP)
2.63
(2.71
EWP)
Replacement Cable Assembly
- OR -
• Adobe Acrobat Reader 8 or higher
• E-10/20/30-IP hardware
• Available LAN with PoE (class 1, <4 watts)
• Ethernet cable ( CAT5 min.)
• 1 MB minimum free hard drive space for installation
• 16MB of free physical RAM
Cut wires from J1 (10 pin connector) and J2 (2 pin
connector).
Remove the two #6 phillips screws fastening the
circuit board.
Cut off any stripped wire ends from the replace-
ment cable.
Using the supplied gel-filled butt connectors, con-
nect corresponding wires from replacement cable
to the previously cut wires from the LED, Call
switch, Speaker and Microphone. See FIGURE 1
for wire color and polarity.
FIGURE 1
(included )
Replacement connectors, wires and
butt connectors for use when replacing
E-10A or E-30-EWP circuit boards.
- Black
LED
+ Red
Black
Call Switch
Black
Red**
Info Switch
Red**
White
Speaker
White
- Black
Mic
+ Red
(not used)
5
Advertisement
Table of Contents
