Page 2
Thank you for purchasing this Yokomo product. This high performance competition kit has been proudly manufactured by Yokomo - World Champion R/C car manufacturer. Proper assembly of this product will provide fun, safe enjoyment. PRECAUTIONS FOR SAFE ENJOYMENT OF YOUR R/C CAR For children under the age of 13, parental guidance is recommended when running.
Page 3
組立てに必要な物 ACCESSORIES AND TOOLS NEEDED FOR KIT ASSEMBLY 走行のために別途お買い求め頂くもの ADDITIONAL ITEMS REQUIRED FOR USE (NOT INCLUDED IN KIT) 2 チャンネルプロポ (1 サーボ、1 アンプ仕様 ) TWO CHANNEL R/C SURFACE RADIO SYSTEM AND ELECTRONIC SPEED CONTROL 走行用7.2Vバッテリーパック (ス トレー トパック/セパレー トタイプ) 7.2V BATTERY PACK (Straight Pack / Saddle Pack Type) 走行用バッテリー充電器...
1. メインシャシーの組立て Main Chassis Assembly このページで使用するパーツ Parts used on this page Z2-002SP2 サイドプレート Side plate Z2-002SP2 サイドプレート L&R 各 1 Side plate L & R 1Ea Z2-0022 メインシャシー ×1 Main Chassis ZC-F38 Z2-0022 M3x8 サラビス メインシャシー FHS Screw Main chassis ZC-F38 M3x8 サラキャップ...
Page 5
3. ベルクランクの取付け Bell Crank Installation このページで使用するパーツ Parts used on this page ZC-BH315 M3x15 ボタンヘッド BHS Screw 袋 #1 の内容 ZC-206SH ロッドエンドボール SS Bag #1 Contents Ball Stud SS ZC-A3610B BB-730-4 1mm アルミスペーサー・黒 Z2-201CL 3x7 ベアリング 1mm Aluminum Spacer ・ Black センターリンク...
4. リヤサスアームの取付け Z2-300RF2 リヤサスマウント・F Rear Suspension Arm Installation Rear Suspension Mount・F Z2-300RF2 / Z2-300RS リヤサスマウントスペーサー・F Rear Suspension Mount Spacer ・F このページで使用するパーツ Parts used on this page 袋 #2 の内容 Bag #2 Contents ZC-F310 M3x10 サラビス FH Screw ※向きに注意 Note position 2-H4 2-H4 Z4-008RS4...
Page 7
5. フロントショックタワーの取付け Front Shock Tower Installation ZC-BH322 M3x22 ボタンヘッド 袋 #3 の内容 BHS Screw Z2-017 Bag #3 Contents フロントショックタワー Front Shock Tower このページで使用するパーツ Parts used on this page ZC-S37 ワッシャー Washer ZC-N3P Z2-017 M3 ナット フロントショックタワー ×1 Front Shock Tower ZC-S37 ZC-N3P ワッシャー...
Page 8
7. リヤアッパーアームマウントの組み立て Rear Upper Arm Mount Assembly ZC-206LH ロッドエンドボール L Ball Stud L 袋 #3 の内容 Bag #3 Contents このページで使用するパーツ ZC-A3610B 1mm アルミスペーサー・黒 Parts used on this page 1mm Aluminum Spacer ・ Black Z2-018M P.9 で使用します。 リヤアッパーアームマウント Used on P.9 Z2-018M Rear Upper Arm Mount リヤアッパーアームマウント...
Page 11
11. バッテリーホルダーの取り付け ZC-BH38 Battery Holder Installation M3x8 ボタンヘッド BHS Screw Z2-018M ギヤボックスサポート Gear Box Support 17 ㎜ 袋 #6 の内容 Z2-118PN Bag #6 Contents バッテリーホルダーポスト Battery Holder Post このページで使用するパーツ Parts used on this page ZR-BP6 スポンジテープ 130x20 ×1 Foam Tape ZS-SS325 M3x25 セットスクリュー...
Page 12
12. ステアリングブロックの組み立て Steering Block Assembly B2-010FH BM-011 フロントアクスル ホイルハブピン ( 黒 ) Front axle Wheel Hub Pin (Black) ZC-206LH 袋 #7 の内容 ロッドエンドボール L ① Ball Stud L Bag #7 Contents ZC-C25N M2x5 キャップスクリュー SH Screw ZC-BH38 BB-105-2 M3x8 ボタンヘッド 5x10 ベアリング...
Page 13
13. フロントサスアームの取り付け Front Suspension Arm Installation Z2-300FB フロントブレース Front Brace B2-009B インナーサスアームピン S Inner Sus. Arm Pin ( Short ) 袋 #7 の内容 Bag #7 Contents このページで使用するパーツ Parts used on this page Z2-001B バンパー Bumper Z2-001B バンパー ×1 Bumper Z2-300FB ZC-F318 フロントブレース...
Page 16
16. フロント&リヤショックの組み立て Front & Rear Shock Assembly ◆フロント用、リヤ用各 2 セットを作ります。 ◆ Assemble 2 front and 2 rear shocks. YS-7A 袋 #10 の内容 O リング・ φ12 Bag #10 Contents O Ring このページで使用するパーツ Z2-S4S Parts used on this page フロントショックボディ Front Shock Body Z2-S4C X33 カラー・A ( 白...
Page 17
17. フロント&リヤショックの組み立てのつづき Front & Rear Shock Assembly ◆フロント用、リヤ用各 2 セットを作ります。 ◆ Assemble 2 front and 2 rear shocks. BM-S812R ショックオイル ショックキャップ Shock Oil オイルは溢れるギリギリ Shock Cap フロント/ #400 まで入れます。 リヤ/ #300 Fill to the rim with Front / #400 shock oil.
Page 19
Make sure that the servo is centered before attaching the servo saver horn. (Refer to your radio manual for more information.) 使用するサーボに合わせてサーボホーンをお選び下さい。 Select the servo saver adapter matching the servo being used. YOKOMO / FUTABA SANWA / KO / JR サーボ (別途ご用意下さい。 ) Hitec Servo (Sold separately.)
Page 20
20. 受信機、スピードコントローラーの取り付け Receiver,ESC Installation 受信機、スピードコントローラーを取り付ける際に取り付け面をクリーナー等で油分や汚れを拭き取ってから固定してください。 Before mounting the receiver and speed controller, use a cleaning agent to remove any oil or dirt from the mounting surfaces. ZR-200A アンテナパイプ Antenna Tube ZC-SS34 M3x4 セットスクリュー 受信機、スピードコントローラー (別途ご用意下さい。 ) Set Screw Receiver and speed controller (Sold separately.) アンテナ線...
21. モーターの取り付け Motor Installation モーター ( 別途ご用意下さい。) Motor ( Sold Separately. ) ZC-S37 ZC-BH36 ワッシャー M3x6 ボタンヘッド Washer BHS Screw ギヤの噛み合わせは 0.3mm 程度ガタつくように合わせます。 ガタが多すぎるとギヤが破損しやすくなるためご注意下さい。 また、この間隔が狭すぎると異音が生じたり、駆動が重くなる ため調整は慎重に行ってください。 Adjust the meshing of the gears so that there is approximately 0.3mm of play in between the teeth. Be careful, as too much play will cause the gears to strip.
Page 22
22. バッテリーの搭載 Battery Installation Z2-118S バッテリースペーサー ( 薄 ) Battery spacer (Thin) Z2-118S バッテリースペーサー ( 厚 ) Battery spacer (Thick) バッテリースペーサーはバッテリー搭載時に、前方に入れてご使用下さい。 When installing the battery, place the battery spacers in the front. ※バッテリースペーサーは袋 #6 に入っています。 The battery spacer are included in bag #6. ショートサイズ...
Page 23
23. タイヤの接着、取り付け Mounting Tires, Wheel Installation タイヤのサイドをめくり、ホイルとの隙間に瞬間接着剤を 流し込み、両サイドを接着します。 Pull the sidewall of the tire slightly away form the rim and apply CA(Cyanoacrylate) glue in between the tire bead and rim. タイヤにインナースポンジを押し込み、タイヤのリブをホイルの溝にはめ込みます。 Place the tire insert into the tire, and tire onto the weel. 瞬間接着剤...
Page 24
24. ボディ、ウイングのカット Body and Wing Cutting φ8mm アンテナ Antenna カットラインに沿ってカットします。 Cut along the cutting line. φ14mm リヤマウントタイプ Rear Mount Type ※ボディ後方のカットラインが異なるのでご注意ください。 ※ Please pay attention to the cutting line in the rear of the body as 26mm there are different cutting lines. 37mm 上記の位置に...
Page 25
25. ボディの塗装&ボディ、ウイングの搭載 Painting the body & Body and Wing Installation ●ボディの塗装 ボディの内側(塗装面)を中性洗剤で油分やホコリを洗い流します。油分やホコリが付着していると、塗装後の剥がれの原因となりますので必ず洗ってください。洗浄後は水分を しっかり拭取ってください。 塗装する前にウインド部分を塗装しないようボディ裏側からマスキングシートを貼ります。その際にマスキングシートがボディに密着していないとにじみの原因になるので注意し てください。 塗料はポリカーボネイト専用(パクトラ製カラースプレーなど)を使用してください。スプレー塗料は1回で厚塗りしてしまうと塗料がたれたり、塗りムラができるので、全体に 薄く塗って乾かし2∼3回に分けて塗装するようにしてください。 ※ボディ表面の保護シートは塗装後に剥がすようにしてください。 ● Painting the body Wash the inside of the body with luke warm water and a mild soap or detergent (such as liquid dishwashing soap) prior to painting. Oil residue or dust will prevent the paint from adhering to the painting surface, and possibly cause the paint to peel later on.
Page 26
リヤショックの取付け ( リヤマウントタイプ ) Rear Shock Installation (Rear Mount Type) リヤショックはサスアームの前方、後方に装着可能です。 後方に装着する際は下記を参照ください。 ※リヤマウントタイプをお選びの際は、ボディは後方のカットラインでカットしてください。 The rear shock can be mounted to the front or rear of the suspension arm. When mounting to the rear-side, refer to the diagram shown below. ※When choosing the Rear Mount Type, the body should be cut at the cut-line located toward the rear of the body. ZC-BH38 M3x8 ボタンヘッド...
Page 27
CIRCUIT INDOOR OUTDOOR WET DRY DUSTY OTHER LOW TRACTION MED TRACTION HIGH TRACTION Ver.01 SMOOTH BUMPY BIUE GROOVE ASTROTURF DRIVER DA TE / / CARPET WOOD Flat ◆CAMBER ° Gull SPRING Z2-017D(Plastic) ◆TOE IN OUT ...