Panasonic WV-CS850B Operating Instructions Manual page 38

• The alarm signal will take approx. 0.2 seconds to
reach the alarm terminal of the VTR after the camera
detects the object.
Because the alarm signal is multiplexed on the
video signal, it may be mistakenly interpreted by
other video equipment as a time code signal.
Therefore, when this camera is not used in a
Panasonic Intelligent CCTV System, select OFF to
prevent the above from occurring.
G Auto Focus Setting (AF MODE)
1. Move the cursor to AF MODE, and select the follow-
ing mode with the joystick. S, M and L stand for
Small, Middle and Large areas respectively in the
centre of a scene that are used for sensing sharp-
ness in auto-focusing.
** SET UP **
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SENS UP
SYNC
WHITE BAL
MOTION DET
AF MODE
RET
AUTO S AUTO M
MANUAL L MANUAL M
MANUAL S, M, L: Auto focus is activated only when
the AF key on the controller is pressed.
AUTO S, M, L: Auto focus is activated automatically
while the pan, tilt or zoom operation is manually
performed. These may be selected in the same
way as MANUAL by pressing the AF key on the
controller.
2. To confirm auto-focus operation, press CAM (SET)
key.
Notes:
• When the electronic sensitivity enhancement (SENS
UP) is activated except in the x2 FIX or x2 AUTO
mode, this function is automatically set to MANUAL
(S, M, L).
• The auto focus lens does not function properly in the
AUTO mode after using the WIDE lens.
• The auto focus lens may not function properly in the
AUTO mode under the following conditions.
1. Dirt or water on window glass.
The auto focus may focus on the dirt or water.
2. Low lighting or illumination.
3. Bright objects or high intensity objects.
4. Single colour object such as a white wall or fine
felt
5. No centre objects and sloping objects
6. Far and near objects on the screen
OFF
ALC
AUTO
ON(MID)
OFF
INT
ATW1
OFF
AUTO L
SPECIAL2
AUTO L
MANUAL S
G Special 2 Menu (SPECIAL2)
This menu lets you adjust and set up the picture quality
to meet your requirements.
Move the cursor to SPECIAL2 and press the F2 button
of WV-CU550C. The special menu appears on the mon-
itor screen. For WV-RM70, hold down the right and left
switches simultaneously for 2 seconds or more.
CAMERA ID
ALC/MANUAL
SHUTTER
AGC
SENS UP
SYNC
WHITE BAL
MOTION DET
AF MODE
RET
• Chroma Level (CHROMA GAIN)
Aperture Level (AP GAIN)
Pedestal Level (PEDESTAL)
1. Move the cursor to CHROMA GAIN, and the "I" cur-
sor is highlighted.
CHROMA GAIN
AP GAIN
PEDESTAL
RESOLUTION
DNR
BW MODE
PIX OFF
REFRESH
CAMERA RESET
RET
2. Move the "I" cursor to your desired position with the
joystick and press the CAM (SET) key to confirm the
level.
Notes:
• For setting the aperture and pedestal levels, per-
form the same steps described above (but in the
step 1, move the cursor to AP GAIN for the aper-
ture level and to PEDESTAL for the pedestal
level).
• To reset the settings to the factory default, press
the F2 button of WV-CU550C/CJ. (For WV-RM70,
hold down the right and left switches simultane-
ously for 2 seconds or more.)
• Resolution (RESOLUTION)
Move the cursor to RESOLUTION and move the joy-
stick to select NORMAL or HIGH.
CHROMA GAIN
AP GAIN
PEDESTAL
RESOLUTION
DNR
BW MODE
PIX OFF
REFRESH
CAMERA RESET
RET
-38-
** SET UP **
OFF
ALC
AUTO
ON(MID)
OFF
INT
ATW1
OFF
AUTO L
SPECIAL2
** SPECIAL2 **
– •••• •••• +
|
– •••• | •••• +
– • ••••••• +
|
NORMAL
LOW2
→ PUSH SET
→ PUSH SET
** SPECIAL2 **
– •••• •••• +
|
– •••• •••• +
|
– • ••••••• +
|
NORMAL
LOW2
→ PUSH SET
→ PUSH SET