Pair To More Than Two Units; Adjusting The Volume - Midland BT Next Conference Instruction Manual

How to pair two BT Next Conference units
The two units supplied in the same BT Next C. box, are already paired and ready to
use, which mean you don't need to perform this procedure. The units are already
paired using the Middle button.
If the devices are not part of the same kit, or the units has been purchased separa-
tely, you need to first pair it in order to use it.
To pair the BT Next C. to another BT Next Conference unit
To pair the BT Next C. to another BT Next C. unit, you must first enter the setup mode:
1. Turn off the unit
2. Press and hold down the middle button about 7 sec., until the Red light is on
permanently.
3. Now press the Middle button for 3 seconds. The Blue and Red light will flash.
4. Do the same procedure on the other unit. When successfully paired, each unit
will have the Blue light on for one second and than go back to the setup mode
(Red light always on).
5. Now the pairing procedure is complete, you just need to exit the setup mode
before you can use the units.
6. Double click on the Middle button, the Red light will turn off and the Blue light
will start flashing.
You can use now your BT Next C..
Attention: remember to switch off all the other Bluetooth device, only the two devices
involved in the pairing must be turned on.
How to use the Intercom with two units
To use the intercom feature, be sure the both units are turned on and correctly paired
together.
Attention: For intercom communication between Driver and Passenger, there is no
need to keep the flip up antenna in the up position. For Bike-to-Bike intercom the an-
tenna must be in the upper position.
Manual activation
Press the Middle button on one of the two units. Communication is enabled and
remains active until you press again the middle button. The intercom need some
seconds to activate, you will hear a beep tone when the intercom is open.
Voice activation (VOX)
Simply start talking, after some seconds the communication will be opened and will
remain active for the time you are talking. If there is no conversation the intercom
will be closed after 40 seconds. If needed you can close the intercom manually wi-
thout waiting 40 seconds (just press the middle button).
If needed, you can disable the VOX feature simply by pressing the Backward button
for 7 sec. A voice announcement will advise you when the VOX is disabled. To turn the
VOX on again, just press the same button and a voice announcement will advise you
22 - Midland BT Next
that the VOX is now active. This setting is remembered also in you turn off the unit.
Attention: The Voice activation (VOX) can open the intercom communication only to
the unit that was paired with the Middle button. If you choose to use a different button
(Rear or ), you will be able to active the intercom only manually.

Adjusting the volume

Your Midland BT Next C. uses AGC technology, which automatically adjusts the liste-
ning volume in relation to background noises.
However, it is also possible to manually adjust the volume by means of the "Volume
+" and "Volume -"buttons.
Attention: volume can be adjust only when an audio connection is active.
How to pair the BT Next Conference to more than two
units
One BT Next C. unit can be paired to maximum five other BT unit, that mean six in
total (3 Midland unit + 2 Talk2All).
The BT Next C. has three main buttons (Forward, Middle and Rear). It is up to you
which button use to pair and activate the intercom, you are totally free to choose the
button you like more. The same button you will use to pair the unit will be also used
to activate the intercom communication.
Remember that each device can always be paired with other 3 units at your choice;
as shown in the picture here below, also 'crossed' pairing can be done.
Rider1
Passenger1
Rider2
For example you can decide to pair one motorbike rider unit to the Forward button,
your passenger to the Middle button and another rider to the Rear button.
In this way you can have in total 5 units paired together and talk to each person,
one by one, simply by pressing the corresponding button (the same used for the
Rider3