Stihl BT 360 Instruction Manual
  1. Manuals
  2. Brands
  3. Stihl Manuals
  4. Lawn and Garden Equipment
  5. BT 360
  6. Instruction manual

Stihl BT 360 Instruction Manual

Hide thumbs Also See for BT 360:
Table of Contents

Advertisement

Quick Links

{
STIHL BT 360
Instruction Manual

Advertisement

Table of Contents
loading

Related Manuals for Stihl BT 360

Summary of Contents for Stihl BT 360

  • Page 1 STIHL BT 360 Instruction Manual...

  • Page 3: Table Of Contents

    English Contents Dear Customer, Guide to Using this Manual Safety Precautions and Working Thank you for choosing a quality engineered STIHL product. Techniques Assembling the Unit It has been built using modern Fuel production techniques and comprehensive quality assurance. Fueling...

  • Page 4: Guide To Using This Manual

    Non- very low intensity. This field may observance of the interfere with some pacemakers. STIHL NOTICE instruction manual may recommends that persons with Caution where there is a risk of...
  • Page 5 (e.g. with a hair net, tool by STIHL or are technically turnover, fuel spillage and damage. cap, hard hat, etc.). identical. If you have any questions in this respect, consult a servicing dealer.
  • Page 6 Do not allow other persons in the work the handles. Throttle cable properly positioned – – area – even when starting. see "Assembling the Machine", "Fitting the Throttle Cable". Start the engine as described in the instruction manual. BT 360...
  • Page 7 - When taking the auger out of the hole, from other persons. tions, even if your model lift the machine vertically so that the tool is equipped with a cata - comes out straight without canting. lytic converter. BT 360...
  • Page 8 Use only a spark plug of the type working, reduce speed on the throttle Service the machine regularly. Do not approved by STIHL and make sure it is lever to achieve greater drilling attempt any maintenance or repair work in good condition – see "Specifications".

  • Page 9: Assembling The Unit

    Fit the plain washers (5) and spring washers (6). Screw on the nuts (7) and tighten Mount the handlebars so that the them down firmly. hole (arrow) in the handlebar (10) is on the right – viewed from the operator. BT 360...
  • Page 10 Use only the throttle cable supplied with washer (14) on the guide (15) as the machine. shown. Fit the cap (16), making sure its two stop lugs (arrows) engage the stop lugs (arrows) on both sides of the guide (15). BT 360...
  • Page 11 Fold the handlebar at the throttle cable side upwards, and the handlebar at the other side downwards – take care not to kink the throttle cable. All hex head screws on the hinges must be tightened down firmly after unfolding the handlebars. BT 360...

  • Page 12: Fuel

    Use only high-quality two-stroke engine STIHL MotoMix uses STIHL HP Ultra location protected from light and the sun. oil – preferably STIHL HP, HP Super or two-stroke engine oil for an extra long Fuel mix ages – only mix sufficient fuel HP Ultra, which are specially formulated engine life.

  • Page 13: Fueling

    Place the fuel pickup body in the Open the filler cap. tank. Fill up with fuel. Take care not to spill fuel while fueling and do not overfill the tank. STIHL recommends you use the STIHL filler nozzle for fuel (special accessory). BT 360...

  • Page 14: Starting / Stopping The Engine

    Guide it slowly back into the housing so that the starter rope can rewind properly. If the engine is new, pull the starter rope several times to prime the fuel system. Move the stop switch (3) to F. BT 360...
  • Page 15 Refit the spark plug – see "Spark Move the stop switch (2) on the Plug". powerhead to STOP. Move the stop switch on the powerhead away from STOP. Move the stop switch on the handlebar to F. BT 360...

  • Page 16: Fitting The Auger

    (1) one the machine in a dry place, well away quarter turn counterclockwise. from sources of ignition, until you need it again. For longer out-of-service periods – see "Storing the Machine". BT 360...

  • Page 17: Releasing A Trapped Auger

    Unscrew the end cover (5) with unwinding torque is exceeded. This wingnut. reduces the risk of damaging the drilling gear. Remove and replace the main filter. Always install a new auxiliary filter together with the new main filter. BT 360...

  • Page 18: Adjusting The Carburetor

    – or sooner if the conditions. electrodes are badly eroded. Install only suppressed spark plugs of the Readjust idle type approved by STIHL – see "Specifications". Removing the Spark Plug WARNING Move the stop switch on the STOP powerhead to STOP.

  • Page 19: Engine Running Behavior

    Have the muffler checked for contamination (carbonization) by your servicing dealer. Check the oil level regularly – once a week in normal operating STIHL recommends that you have conditions. servicing and repair work carried out exclusively by an authorized STIHL Remove the auger.

  • Page 20: Rewind Starter

    Have a damaged starter rope replaced and air filter. by your dealer before it breaks Store the machine in a dry, high or completely. STIHL recommends that locked location, out of the reach of you have servicing and repair work children and other unauthorized carried out exclusively by an authorized persons.

  • Page 21: Maintenance And Care

    Readjust electrode gap Spark plug Replace after every 100 operating hours Have checked by dealer Spark arresting screen in muffler Have cleaned or replaced by servicing dealer All accessible screws and nuts (not adjust - Retighten ing screws) BT 360...
  • Page 22 (very dusty work area, etc.), shorten the specified intervals accordingly. Checking oil level Gearbox Change gearbox oil Drilling spindle Clean Check Auger Replace Safety labels Replace not in all versions, market-specific STIHL recommends a STIHL servicing dealer. BT 360...

  • Page 23: Minimize Wear And Avoid Damage

    English servicing dealer. STIHL dealers are Minimize Wear and Avoid regularly given the opportunity to attend Damage training courses and are supplied with the necessary technical information. Observing the instructions in this manual helps reduce the risk of unnecessary If these maintenance operations are not wear and damage to the power tool.

  • Page 24: Main Parts

    10 Handle frame (foldable) 11 Retainer 12 Stop switch on handlebar 13 Clamp ring 14 Drilling spindle 15 Auger 16 Stop switch on powerhead 17 Choke knob 18 Interlock lever 19 Filler plug 20 Idle speed screw (LA) Serial number BT 360...

  • Page 25: Specifications

    K - factor in accordance Lubrication: EP 90 (SAE 90) Engine with Directive 2006/42/EC is 2.0 m/s milldly alloyed for the vibration measurement. gear oil STIHL single cylinder two-stroke engine Oil capacity: 0.5 l REACH Displacement: 60.3 cm Augers Bore:...

  • Page 26: Special Accessories

    When repairing the machine, only use the garbage can. Take the product, replacement parts which have been accessories and packaging to an approved by STIHL for this power tool or approved disposal site for environment- are technically identical. Only use high- friendly recycling.

  • Page 27: Ec Declaration Of Conformity

    English EC Declaration of Conformity ANDREAS STIHL AG & Co. KG Badstr. 115 D-71336 Waiblingen confirms that the product described below Category: Earth Auger Make: STIHL Model: BT 360 Serial identification: 4308 Displacement: 60.3 cm conforms to the specifications of...
  • Page 28 0458-441-0121-B englisch www.stihl.com *04584410121B* 0458-441-0121-B...

Table of Contents