MultiSystem ........2 Guide to Using this Manual ....2 Thank you for choosing a quality Safety Precautions ......3 engineered STIHL product. Working with the unit ......9 This machine has been built using Approved MultiEngines ....11 modern production techniques and Mounting the MultiTool ....
Note or hint on correct procedure in contain item numbers that appear in the order to avoid damage to the illustration. environment. In the STIHL MultiSystem the Example: MultiEngine can be combined with a Loosen the screw (1) number of different MultiTools to produce a power tool.
STIHL dealer for Only rotor blades supplied by STIHL or assistance. Always observe local safety regulations, expressly approved by STIHL for use standards and ordinances.
Page 5
See also notes on "Transporting the leather. Power Tool" in the MultiEngine instruction manual. STIHL has a full line of safety clothing and equipment. BF-MM, BK-MM...
Page 6
Keep the handles dry and clean for blades. The blades begin safe control. to rotate as soon as the engine is started in the "Start" position. Always stand to one side of the machine when starting – never in front of the blades. BF-MM, BK-MM...
Page 7
Do not operate using the starting throttle lock as you do not have control of the engine speed. To reduce the risk of injury from contact with the blades, never operate your unit without the specified deflector. BF-MM, BK-MM...
Page 8
If the blades still regular intervals – always shut off the To reduce the risk of injury from contact rotate, have your STIHL dealer check engine and make sure the blades have with the blades, do not allow your power tool and make proper stopped before cleaning.
Page 9
Be particularly alert and cautious when Do not attempt any maintenance or the engine and remove the spark plug wearing hearing protection because repair work not described in the BF-MM, boot before checking or changing your ability to hear warnings (shouts, BK-MM MultiTool and MultiEngine attachments alarms, etc.) is restricted.
MultiTools with rotor blades are available in two versions: The rotor blades may only be operated Pick tines in one position. Arrows on the rotors Bolo tines indicate the required direction of rotation, refer to "Mounting the MultiTool". BF-MM, BK-MM...
Page 11
Then level the entire prepared area with The bolo tines are particularly suitable a rake. for working through soil which is well cultivated and not compacted. BF-MM, BK-MM...
Approved MultiEngines Working in soil additives Cultivator spur Only MultiEngines which have been supplied by STIHL or specially approved Humus soil, compost, leaves or other for use with this MultiTool may be used. organic substances and fertilizers can be worked into the soil with this unit.
(3). – Tighten first screw moderately. See also "Mounting the MultiTool" in the – Tighten second screw moderately. instruction manual of the other MultiTool – Tighten down first screw firmly. – Tighten down second screw firmly. BF-MM, BK-MM...
(5) on the shaft until it can be near the blades. pushed into position – check the With your left hand on the loop direction of rotation again (arrows). handle, press the unit firmly against the ground. BF-MM, BK-MM...
The power tool must be operated, be performed by the owner, they should maintained and stored with the due care be performed by an authorized STIHL and attention described in these servicing dealer. To shut down the engine instruction manuals.
Page 16
Among other parts, this includes: – Rotor blades – Rotor blade mounting hardware – Deflector BF-MM, BK-MM...
2.0 kg When repairing the machine, only use replacement parts which have been conforms to the specifications of approved by STIHL for this power tool Directive 98/37/EC. or are technically equivalent. Only use The product has been developed and high-quality replacement parts in order...
All STIHL products comply with the highest quality standards. An independent organization has certified that all products manufactured by STIHL meet the strict requirements of the ISO 9001 standard for quality management systems in terms of product development, materials purchasing, production, assembly, documentation and customer service.
Need help?
Do you have a question about the BF-MM and is the answer not in the manual?
Questions and answers