Page 1
VAA22024-R.3749.A 作成承認印 配布許可印 サービス 計画課 M VMA22024 REPAIR MANUAL Copyrigh c 2008 by Nikon Corporation. All Rights Reserved. 無断転載を禁ず !! Printed in Japan FEB 2008...
Page 2
VMA22024-R.3749.A CONTENTS DISASSEMBLY WARNING ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ D1 EXTERNAL SCREW ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ D2~D3 BACK COVER ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ D3~D4 DISCHARGE OF MAIN CONDENSER ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ D5 LCD UNIT ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ D5 LCD HOLDER・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ D6 CP-1 PCB ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ D7~D9 LENS UNIT ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ D10~D11 STRAP HOLDER ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ D12 USB COVER ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・...
Page 4
VMA22024-R.3749.A Disassembly WARNING There are high voltege parts inside. Be careful of this electric shock, when you remove the cover. You must discharge the main condenser according to the instruction of this repair manual after you remove the cover. Points to notice for Lead-free solder products ・...
Page 5
VMA22024-R.3749.A EXTERNAL SCREW ・ Remove the two screws [#102]. ・ Remove the two screws [#101]. Be careful of a difference in size between the upper and lower screws. Screw[#102] Screw[#101] ・ Remove the two screws [#102]. Screw [#102] - D2・S20 -...
Page 6
VMA22024-R.3749.A ・ Remove the two screws [#101]. Screw [#101] BACK COVER ・ Remove the BACK COVER [#119]. Hook - D・S20 -...
Page 7
VMA22024-R.3749.A Remove the SPACER ・ - D・S20 -...
Page 8
VMA22024-R.3749.A WARNING There are high voltege parts inside. Be careful of this electric shock, when you remove the cover. You must discharge the main condenser according to the instruction of this repair manual after you remove the cover. DISCHARGE OF MAIN CONDENSER Be careful NOT to touch the decoration plate.
Page 9
VMA22024-R.3749.A LCD HOLDER ・ Take out the screw [#108]. ・ Take out the screw [#107]. ・ Take out the three screws [#106]. Screw [#106] Screw [#108] LCD HOLDER [#117] Screw [#107] Screw [#106] Screw [#106] ・ Remove the LCD HOLDER [#117]. ・Remove the FPC.
Page 11
VMA22024-R.3749.A ・ Unsolder the wires [Gray] and [Black]. ・ Unsolder the wires [Red] and [White]. ・ Remove the soldering bridge. Wire [Red] Wire [Gray] Wire [Black] Wire [White] ・ Take out the screw [#106]. ・ Remove the FPC. Screw [#106] - D・S20 -...
Page 12
VMA22024-R.3749.A ・ Remove the CP-1 PCB [#114]. CP-1 PCB [#114] ・Remove the SPACER [#116]. ・Remove the SPACER [#115]. SPACER [#115] SPACER [#116] SPACER [#115] - D・S20 -...
Page 13
VMA22024-R.3749.A LENS UNIT ・ Take out the three screws [#104]. Screw [#104] LENS UNIT [#15] Screw [#104] ・ Remove the LENS UNIT[#15] . - D0・S20 -...
Page 15
VMA22024-R.3749.A STRAP HOLDER ・ Remove the STRAP HOLDER. STRAP HOLDER ・ Take out two screws [#103]. STRAP HOLDER [#12] Screw [#103] HOLDER BASE [#13] - D2・S20 -...
Page 16
VMA22024-R.3749.A USB COVER ・ Remove the screw [#101]. ・ Then, take out the other screw of the right picture. EARTH Screw [#101] EARTH Screw ・ Remove the EARTH. (Holding down the USB cover makes it easier to remove the earth.) ・...
Page 17
VMA22024-R.3749.A COVER LENS ・ Take out the four screws [#109]. FRONT COVER UNIT Screw [#109] ・Remove the COVER LENS [#221]. - D・S20 -...
Page 24
VMA22024-R.3749.A Take out the screw [#106]. ・ ST-1 PCB[#244] screw [#106] Unsolder the wire [White]. ・ wire [White] ・Remove the ST-1 PCB[#244]. ST-1 PCB[#244] - D2・S20 -...
Page 25
VMA22024-R.3749.A ・ Remove the TRIGGER COVER [#243]. ・Unsolder the wires [Blue] and [Brown] and [Black]. TRIGGER COVER [#243] Wire [Blue][Brown][Black] ・Remove the SPACER [#246]. ・Remove the SPACER [#247]. ・Remove the SPACER [#248]. SPACER [#248] SPACER [#246] ST-1 PCB [#244] SPACER [#247] - D22・S20 -...
Page 26
VMA22024-R.3749.A MAIN CONDENSER ・Unsolder at two places. ・ Remove the MAIN CONDENSER . Unsolder here. MAIN CONDENSER ・Peel off SPACER [#245] from the main condenser. SPACER [#245] MAIN CONDENSER - D2・S20 -...
Page 27
VMA22024-R.3749.A FLASH UNIT ・Unhook at two places. ST-1 PCB [#244] Unhook here. ・The FLASH UNIT will come off from the PCB. FLASH UNIT - D2・S20 -...
Page 28
VMA22024-R.3749.A ・Unhook the FLASH HOLDER at three places, and remove the flash lamp from the front side. ・Remove the SPACER [#240]. ・Remove the SPACER [#241]. Caution: The reflector of the flash lamp is easily bent, so handle it with care. SPACER [#241] SPACER [#240] FLASH HOlDER [#239]...
Page 30
VMA22024-R.3749.A BATTERY COVER ・Remove the BATTERY COVER[#225]. BATTERY COVER[#225] ・Remove the BATTERY LABEL[#224]. BATTERY LABEL[#224] - D2・S20 -...
Page 31
VMA22024-R.3749.A Assembly BATTERY COVER ・Attach the battery label [#224] inside the frame as below. ・Apply the grease (MZ-800SEL) to the four places of the plate. Grease:MZ-800SEL ・Mount the BATERY COVER [#225]. - A・S20 -...
Page 32
VMA22024-R.3749.A INNER HOLDER ・Solder the BATTERY TERMINAL [#231] and wire [#232]. Caution: The solder must not be squeezed out from this surface. ・ Set the BATTERY TERMINAL [#231][#229] to the INNER HOlDER[#226]. Put into the position where the terminal is locked. BATTERY TERMINAL [#231] BATTERY TERMINAL[#229]...
Page 33
VMA22024-R.3749.A Adhere the SPACER [#234] ・ SPACER [#234] Reference position ・Adhere the SPACER [#235]. SPACER [#235] Reference position Adhere firmly. - A・S20 -...
Page 34
VMA22024-R.3749.A Adhere the SPACER [#230]. ・ Reference position SPACER [#230] Adhere the SPACER [#236]. ・ Reference position SPACER [#236] - A・S20 -...
Page 35
VMA22024-R.3749.A Adhere the SPACER [#233]. ・ Reference position SPACER [#233] - A・S20 -...
Page 36
VMA22024-R.3749.A ・Adhere the SPACER [#237]. Reference position SPACER [#237] - A・S20 -...
Page 37
VMA22024-R.3749.A ST-1 PCB ・Adhere the SPACER [#247]. Adhere in the square area surrounded by white line. Reference position ・Adhere the SPACER [#248]. Reference position - A・S20 -...
Page 38
VMA22024-R.3749.A ・Adhere the SPACER [#246]. Reference position MAIN CONDENSER ・Adhere the SPACER [#245] to the main condenser. SPACER [#245] MAIN CONDENSER - A・S20 -...
Page 39
VMA22024-R.3749.A ・Mount the MAIN CONDENSER.. ・Solder at two places. Solder here. FLASH UNIT ・Hook the FLASH UNIT at two places. Hook here. - A・S20 -...
Page 40
VMA22024-R.3749.A ・Adhere the SPACER [#241]. ・Adhere the SPACER [#240]. ・Mount the FLASH LAMP [#238]. SPACER [#241] SPACER [#240] FLASH HOLDER [#239] FLASH LAMP [#238] SPACER [#241] Reference position Reference position SPACER [#240] Wires [Blue][Brown] Wire [Black] - A0・S20 -...
Page 41
VMA22024-R.3749.A ・Solder the wires [Blue] and[Brown] and [Black]. ・Adhere the TRIGGER COVER [#243]. TRIGGER COVER [#243] [Blue][Brown][Black] ・Be careful of wiring. ・Be careful of the direction of attaching the trigger cover [#243]. Wiring position - A・S20 -...
Page 42
VMA22024-R.3749.A ・Mount the ST-1 PCB [#244] on the inner holder [#226]. Set it by fitting with the boss. ストロボ管 When the PCB is mounted, be careful NOT to pinch the white wire in the strobe tube, etc. Solder the wires [White]. ・...
Page 43
VMA22024-R.3749.A Tighten the two screws [#106]. ・ ST-1 PCB [#244] Screw [#106] ・Adhere the SPACER [#249]. Reference position SPACER [#249] SPACER [#249] Adhere the SPACER as if it covers the wires [Brown][Black]. - A・S20 -...
Page 44
VMA22024-R.3749.A ・Pass the wire [Blue] in the cutout of the flash holder and arrange it. ・Arrange the wire [White] as shown in the right picture. Cutout [White] wire must NOT be put over [Blue] wire. ・Adhere the SPACER [#242] Reference position SPACER [#242] - A・S20 -...
Page 45
VMA22024-R.3749.A SPEAKER/MICRPHONE ・Set the SPEAKER [#228] SPEAKER [#228] ・Set the MICRPHONE [#227] MICRPHONE [#227] - A・S20 -...
Page 46
VMA22024-R.3749.A DECORATION PLATE ・Adhere the SPACER [#250]. ・Adhere the SPACER [#251]. ・Adhere the SPACER [#252]. SPACER [#250] SPACER [#251] SPACER [#252] Adhere the SPACER along the edge of the convex portion of the plate. The SPACER must be put under the plate. - A・S20 -...
Page 47
VMA22024-R.3749.A ・Install the DECORATION PLATE [#253] by aligning it with the bosses. DECORATION PLATE [#253] Tighten the screw [#106]. ・ Screw [#106] - A・S20 -...
Page 48
VMA22024-R.3749.A FRONT COVER ・Engage the hook from top to bottom in numeric order. ① Hook here. ② In order to make the procedure easier, hook ① first and then ② as if pulling downwards. ・Attach the FRONT COVER [#223] to the INNER HOLDER [#226]. - A・S20 -...
Page 49
VMA22024-R.3749.A COVER LENS ・Adhere the SPACER [#222]. COVER LENS [#221] For removing the unnecessary portion SPACER [#222] (center) of the SPACER, push it toward the inside from the outside. ・Fit with bosses. This part must face downwards. - A・S20 -...
Page 50
VMA22024-R.3749.A ・Tighten the four screws [#109]. FRONT COVER UNIT screw [#109] USB COVER ・Put the USB cover [#11] upright as below, and turn it in the direction of the arrow to set. - A20・S20 -...
Page 51
VMA22024-R.3749.A ・ Set the EARTH. (Holding down the USB cover makes it easier to set the earth.) ・ Set the TRIPOD SOCKET. Hold down. TRIPOD SOCKET USB COVER [#11] ・ Tighten the screw of the below picture. ・ Then, tighten the other screw [#101]. Screw [#101] EATRTH Screw...
Page 52
VMA22024-R.3749.A STRAP HOLDER ・Tighten the two screws [#103] Set it by fitting it with the boss. Screw [# 103] STRAP HOLDER[#12] HOLDER BASE [#13] ・ Set the STRAP HOLDER. STRAP HOLDER - A22・S20 -...
Page 53
VMA22024-R.3749.A LENS UNIT ・Adhere the TAPE [#110]. Reference position TAPE [#110] ・Adhere the TAPE [#16]. Reference position TAPE [#16] - A2・S20 -...
Page 54
VMA22024-R.3749.A ・Fold the FPC as below. Fold the FPC along the marked dot line. - A2・S20 -...
Page 55
VMA22024-R.3749.A ・Solder at the two places. Solder RECHARGEABLE BATTERY [#113] ・Adhere the SPACER [#111]. SPACER [#111] ① Wrap the spacer as shown by the arrow. Reference position ② Glue the shaded portion together. - A2・S20 -...
Page 56
VMA22024-R.3749.A ・Set the SPACER [#18]. ・Mount the CCD UNIT [#112]. SPACER [#18] Cutout CCD UNIT [#112] FLAT Convex CCD side LENS side ・Tighten the screws [#105] in numeric order from ① to ② . ① ② - A2・S20 -...
Page 57
VMA22024-R.3749.A ・Peel off the backing paper of TAPE [#110], and attach the tape to CCD UNIT. TAPE [#110] - A2・S20 -...
Page 58
VMA22024-R.3749.A ・ Install the LENS UNIT [#15] by fitting with the bosses. ・ Tighten the three screws [#104]. Screw [#104] LENS UNIT [#15] Screw [#104] - A2・S20 -...
Page 59
VMA22024-R.3749.A ・Adhere the TAPE [#17]. Reference position TAPE [#17] - A2・S20 -...
Page 60
VMA22024-R.3749.A CP-1 PCB ・Install the CP-1 PCB [#114] by fitting with the bosses. ・ Set the FPC. ・ Tighten the screw [#106]. Screw [#106] - A0・S20 -...
Page 61
VMA22024-R.3749.A ・Adhere the SPACER [#115]. Adhere in the square area surrounded by white line. ・Adhere the SPACER [#116]. ・Adhere the SPACER [#120]. Reference position SPACER [#120] SPACER [#116] - A・S20 -...
Page 62
VMA22024-R.3749.A ・ Solder the wires [Gray] and [Black]. ・ Solder the wires [Red] and [White]. ・ Solder the soldering bridge. Wire [Gray] Wire [Red] Wire [White] Wire [Black] ・Arrange all the wires [Gray][Black][Red][White] as below. - A2・S20 -...
Page 63
VMA22024-R.3749.A ・Set the SPACER [#]. Reference position LCD HOLDER ・Set the LCD HOLDER. LCD HOLDER [#117] Set it by fitting with the boss. - A・S20 -...
Page 64
VMA22024-R.3749.A ・ Tighten the screw [#0]. ・ Tighten the screw [#0]. ・Tighten the three screws [#106] Screw [#106] Screw [#108] LCD HOLDER [#117] Screw [#107] Screw [#106] Screw [#106] LCD UNIT ・ Set the FPC. ・ Mount the LCD UNIT [#118]. LCD UNIT [#118] Retainer plate Retainer plate...
Page 65
VMA22024-R.3749.A BACK COVER ・Adhere the SPACER. Reference position ・ Install the REAR COVER [#119]. Hook here. - A・S20 -...
Page 66
VMA22024-R.3749.A EXTERNAL SCREW ・ Tighten the two screws [#101]. Screw [#101] ・ Tighten the two screws [#102]. Screw [#102] - A・S20 -...
Page 67
VMA22024-R.3749.A ・ Tighten the two screws [#102]. ・ Tighten the two screws [#101]. Be careful of a difference in size between Screw [#102] the upper and lower screws. Screw [#101] NAME PLATE ・Adhere the NAME PLATE [#14]. Reference position of double-stick tape.
Page 68
VMA22024-R.3749.A ADJUSTMENT 1. Equipment IBM compatible PC/AT ・ AC adapter EH-62D ・ USB cable (UC-E6) ・ AC adapter EH-62D ・ USB cable (UC-E6) AC adapter EH-62D ・ USB cable (UC-E6) ・ USB cable (UC-E6) USB cable (UC-E6) 2. Servicing tools Pattern box, color meter, luminance meter, calibration software (J65098), ajustment collimator (J63090) 3.
Page 69
VMA22024-R.3749.A 4. Firmware upgrading Device ・ AC adapter EH-62D AC adapter EH-62D ・ SD card to be used for upgrading the firmware: 1 pc. SD card to be used for upgrading the firmware: 1 pc. [Creating the upgrading SD-card] 1) Format the SD card by PC. 2) Make a folder named “firmware”...
Page 70
VMA22024-R.3749.A ・ The message that indicates the completion appears. ・ Turn camera Turn camera OFF and remove the SD card. ・ Turn camera ON to check the version. ・ Turn camera OFF to end the procedure. - A40 ・ S210-...
Page 71
VMA22024-R.3749.A 5. Setup System requirements Windows ® 2000, XP ・IBM-compatible PC/AT with Pentium or higher processor ・IBM-compatible PC/AT with Pentium or higher processor IBM-compatible PC/AT with Pentium or higher processor ・Windows ・CD-ROM drive CD-ROM drive ・3.5-inch 2HD diskette drive ・3.5-inch 2HD diskette drive ・3.5-inch 2HD diskette drive 3.5-inch 2HD diskette drive ・USB port...
Page 72
VMA22024-R.3749.A 6. Pattern box Before using the pattern box, turn its power on to carry out “Aging” approx. 30 minutes: the color temperature must be adjusted to 3100 ± 20K by the color meter, and the luminance must be adjusted to 900 ± 20cd/m by the luminance meter.
Page 73
VMA22024-R.3749.A e.g. Coefficient 1365.2cd/ ㎡ 168.89× 900cd/ ㎡ = 256 Coefficient The calculated result corresponds to " EV12.4 " of the inspection report. 7. Adjustments required when parts are replaced CCD black / Lens white dot defect Firmware up ○ Adjustment is necessary. 2- 4....
Page 74
3-5. カメラとパソコンとの接続 1. ケーブルのカメラコネクターをカメラのUSBポートに合わせてコネクターを差し込みます。 VMA22024-R.3749.A 2. パソコンのUSBポートに接続します。 8. Connecting the camera to the computer 1) Insert the camera connector of the cable to the USB port of the cradle correctly. 2) Connect to the USB port of the personal computer. Supply the power from the AC adapter EH-62D.
Page 75
VMA22024-R.3749.A Calibration software ・ Connect the camera to the personal computer with USB. ・ Turn the camera on. Turn the camera on. ・ When the calibration software starts, the following is displayed on the PC monitor. When the calibration software starts, the following is displayed on the PC monitor. Calibration software ・...
Page 76
VMA22024-R.3749.A 10. Lens adjustment Lens adjustment Calibration software [Preparations] ・ Turn on the power switch of the adjustment collimator (C-DSC) J63090. ・ Turn the camera on. [Conditions] ・ Set “nearest distance” for the distance between the adjustment collimator and camera (front surface of lens). Set “nearest distance”...
Page 77
VMA22024-R.3749.A 11. AWB adjustment [Preparations] ・ Pattern Box (Color temperature: 3100 ± 20K, Luminance: 900 ± 20cd/m [Conditions] ・ Fix the pattern box so that the distance may be “0cm” between the pattern box and camera (front surface of lens). Note) Do not allow outside light to enter in.
Page 78
VMA22024-R.3749.A 12. CCD white dot defect compensation [Conditions] ・ With the lens shutter being closed, read the defect of CCD pixels. Then, make the correction data and rewrite the data by the following procedure. Correct the upper level of defective 6000 pixels from the brightest number of CCD pixels.. [How to adjust] ・...
Page 79
2. Double-click on the "DscCa1Di.exe". 3. Click on the "Get" button in the USB storage window and check the USB storage data. VID: NIKON PID: DSC COOLPIX S210 Serial: Rev. : 1.00 4. Check the "Serial" in the above USB storage data. If the displayed value is different from the serial number of the camera bottom, enter the number of the camera bottom, and click the "Set"...
Page 80
VMA22024-R.3749.A 15. Language setting “Lang, number” enables to select either “2 Languages” or “20 Languages”. Caution) Select “2 Languages” for Japanese models. 2 Languages 20 Languages 16. Factory default How to set: 1.Provide power via battery or AC adapter. (Card is not necessary.) 2.Turn camera ON.
VMA22024-R.3749.A 1. OUTLINE OF CIRCUIT DESCRIPTION 1-1. CCD CIRCUIT DESCRIPTION 1. IC Configuration The CCD peripheral circuit block basically consists of the fol- lowing ICs. IC913 (ICX646CQZ) CCD imager IC905 (AD9971BCPZRL) CDS, AGC, A/D converter, H driver IC901 (LR366877) V driver 2.
Page 82
VMA22024-R.3749.A 4. IC905 (CDS, AGC Circuit and A/D Converter) 3. IC905 (H Driver) and IC901 (V Driver) An H driver and V driver are necessary in order to generate The video signal which is output from the CCD is input to pins (25) of IC905.
Page 83
VMA22024-R.3749.A 1-2. CP1 CIRCUIT DESCRIPTION 1. Circuit Description 2. Outline of Operation 1-1. Signal processor (SG) When the shutter opens, the serial signals (“take a picture” 1. Signal preprocessing block commands) from the 8-bit microprocessor is input to ASIC This block processes the raw data for the CCD. (IC101) and operation starts.
Page 84
VMA22024-R.3749.A 4. Lens drive block 4-1. Zoom drive The parallel signals (ZIN1 and ZIN2) which are output from the ASIC (IC101) are used to drive (ZOUT1 and ZOUT2) by the motor driver IC, and then used to drive the zoom DC mo- tor.
Page 85
VMA22024-R.3749.A 1-3. PWA POWER CIRCUIT DESCRIPTION 1. Outline 3. Analog +13 V (A) Power Output This is the main power circuit, and is comprised of the follow- +13 V (A) is output. Feedback for the +13 V (A) is provided to ing blocks.
Page 86
VMA22024-R.3749.A 1-4. SYA CIRCUIT DESCRIPTION 1. Configuration and Functions For the overall configuration of the SYA block diagram, refer to the block diagram. The SYA block centers around a 8-bit micropro- cessor (IC301), and controls camera system condition (mode). The 8-bit microprocessor handles the following functions. 1.
Page 87
VMA22024-R.3749.A Strobo charge control CHG_ON COMREQ/ZBOOT Command request BACKUP_CTL Backup battery charge control NOT USED BAT_TEMP Battery temperature detection BAT_OFF Battery OFF detection signal input SREQ Serial communication request signal Shutter 2nd detection SHUTTER 2nd NOT USED RESET Backup reset detection Clock oscillation terminal for clock (32.768 kHz) XCIN Clock oscillation terminal for clock (32.768 kHz)
Page 88
VMA22024-R.3749.A 3. Key Operaiton For details of the key operation, refer to the instruction manual. SCAN SCAN MODE LEFT MENU TEST DOWN PW_TEST RIGHT Table 4-2. Key Operation 4. Power Supply Control The 8-bit microprocessor controls the power supply for the overall system. The following is a description of how the power supply is turned on and off.
Page 93
CL303 1AV4J11VW131G ASIC_SDO CN302 ASIC_SDI SREQ TO SW UNIT TO DMA PW_ON SHUTTER1st SHUTTER2nd TELE PLAY WIDE MODEL: COOLPIX S210 CIRCUIT DIAGRAM: CP1 (SYA) SCAN IN SCAN OUT MODE LEFT MENU TEST DOWN PW_TEST RIGHT - E13 ・ S210 -...
Page 101
VMA22024-R.3749.A POWER ブロック図 POWER BLOCK DIAGRAM 33 SHDNB1 IC501 34 AVDD UPD168802K8-4E5-E1 17 PVDD L5301 BOOST4.5V STEP UP CIRCUIT SWITCHING 20, 21 LOUT[11, 12] IC505 PAON4 CONTROL 18, 19 DOUT[11, 12] XC6221S05XG -3.5V(A) 4, 5 LOUTA[21, 22] L5002 VDD3 STEP UP & DOWN 6, 7 LOUTB[21, 22] IC504 CIRCUIT...
Page 102
VMA22024-R.3749.A FUSE ARRANGEMENT Phenomenon when FUSE has FUSE Function of FUSE Rating blown out Protects when the DC/DC converter circuit F5001 The power is not turned on. 32V/2A malfunctions. Protects when the speed light charging circuit F5002 The speed light is not charged. 32V/2A malfunctions.
Page 103
VMA22024-R.3749.A INSPECTION STANDARDS Items Judgment standards Remarks External view Gap/Difference in Visual observation ・ General components height Gap: 0.2mm or less Difference in height: 0.15mm or less (When the lens-barrel is retracted, gap between the lens-barrel & zoom frame on flattened surface: 0.25mm or less; When the lens-barrel is extended, gap between zoom frame &...
Page 104
VMA22024-R.3749.A Items Judgment standards Remarks ・ Clear clicking feeling and smooth touching. Neither outstanding "caught/rubbed-in-mechanism" touch NOR gap . (Make a check in normal operation.) (If there is a play, do not move the switch to the “OFF” side excessively.) Operation/Operability Operation touch ・...
Page 105
VMA22024-R.3749.A Items Judgment standards Remarks Lens capacity Ghost/Flare Point light source ・ No outstanding ghost/flare. Visual observation Surface light source ・ No outstanding flare at the center. Distortion ・ No outstanding deformation. Visual observation (Design ( ∞ ) W : -1.5%, T : +0.6%) Dust in a picture ・...
Page 106
VMA22024-R.3749.A Items Judgment standards Remarks Guide No. FULL ・ 5.2 ± 0.4 EV Flash meter (ISO100・m) (Charge for 10 seconds with the new secondarybattery and perform Secondary battery measurement within 1 second.) Recycle time ・ Within 6 seconds Stop watch ・...
Page 107
VMA22024-R.3749.A Items Judgment standards Remarks Infinity set by manual ・ The resolution must correspond to the following value in the Infinity chart whole zoom area. Center horizontal/vertical: 950 TV pcs or more. (Take a picture for the whole zoom area in the high image quality mode.) (Shoot the infinity collimator image on condition that aperture is open in the scene distance view/night view mode and the image...
Page 109
VMA22024-R.3749.A Items Judgment standards Remarks Color reproduction (1) Put the image mode back on the initial setting. (2) Set "Macbeth" chart in the standard light-source equipment. Color bar chart Setting position: Approx. 25cm-distance from the bottom of the Photoshop equipment to the center of the chart (3) Set ISO sensitivity to "64".
Page 110
VMA22024-R.3749.A Items Judgment standards Remarks Visual field ratio ・ No shading in the LCD display range. Visual observation ・ The inclination of the image and the monitor frame must be 0.5° or less. ・ The vertical difference and horizontal difference of the black belt width in the image periphery must be within 0.3mm.
Page 111
VMA22024-R.3749.A Items Judgment standards Remarks Electric characteristics Consumption current ・ When card is not used: 0.27mA or less (when the power switch is Constant voltage Stand-by (idle) current OFF) power supply ・ When card is used: 0.39mA or less (when the power switch is Ammeter OFF) Start (Photography)
Page 112
VMA22024-R.3749.A Items Judgment standards Remarks ・ When voltage increases, connect the constant-voltage power supply and check the voltage at Level 3 ("Battery exhausted"). Then, turn off the power, increase the voltage in increments of 0.1V and turn the SW from OFF to ON. Measure the voltage under the following conditions.