Back Panel; Power Switch - Peavey XR s Operating Manual

Back Panel

47
POWER
ON
50/60 Hz 185 WATTS
Consumo de energia 185 Wh
A/C
49

POWER SWITCH

47
This is the main power switch.
FUSE
48
This is the main safety fuse for the AC line voltage. Only replace with a fuse of the exact type and rating. If the fuse continues to open, do not
over fuse. Take the unit to an authorized Peavey service center.
NOTE: If the main AC voltage is changed, the fuse must also be changed to one of the appropriate rating for the voltage you are switching to.
AC Power Inlet
49
This is the receptacle for an IEC line cord, which provides AC power to the unit. Connect the line cord to this connector to provide
power to the unit. Damage to the equipment may result if improper line voltage is used. Never break off the ground pin on any equip-
ment. It is provided for your safety. If the outlet used does not have a ground pin, a suitable grounding adapter should be used and
the third wire should be grounded properly. To prevent the risk of shock or fire hazard, always make sure that the amplifier and all associated
equipment is properly grounded.
NOTE: FOR UK ONLY
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the ter-
minals in your plug, proceed as follows: (1) The wire which is coloured green and yellow must be connected to the terminal which is
marked by the letter E, or by the Earth symbol, or coloured green or green and yellow. (2) The wire which is coloured blue must be
connected to the terminal which is marked with the letter N, or the colour black. (3) The wire which is coloured brown must be con-
nected to the terminal which is marked with the letter L, or the colour red.
To avoid the risk of electrical shock, do not place fingers or any other objects into empty tube sockets while power is being supplied to unit.
Voltage Selector Switch
50
This switch allows the user to select between 115VAC / 60Hz or 230VAC / 50Hz. To change the voltage selector, you must first un-
screw and remove the plastic cover that protects the switch. After changing the voltage, please replace the plastic cover to ensure the
voltage level is not inadvertently altered.
NOTE: The fuse MUST be changed to the appropriate value to match the voltage you have selected. Please see the note on the back of the
mixer for the correct value.
POWER AMP 1 SPEAKER OUTPUTS (MAIN MIX)
51
Dual two-conductor ¼" – Speakon combination jacks that can be connected to your speakers. Each amplifier has a minimum load impedance
of 4 ohms. This means you can connect either one 4-ohm, one 8-ohm or two 8-ohm speakers to each amplifier. Do not operate below rated
minimum impedance. For maximum power transfer and to prevent damage to your amplifier, be sure to use speaker cables and not instru-
ment cables to connect to the speakers. We recommend the use of 18-guage or larger speaker wire.
48
CAUTION
FUSE
AVIS:
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
115V PIN 7878
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
T10AH/250V
THIS APPARATUS SHOULD NOT BE EXPOSED TO RAIN OR MOISTURE
220-240V AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT
BE PLACED ON THIS APPARATUS. TO PREVENT THE RISK OF FIRE
T5AH/250V
HAZARD, REPLACE WITH SAME TYPE 250 VOLT FUSE.
AVIS:
DANS LE BUT DE REDUIRE LES RISQUES D'INCENDIE OU DE
DECHARGE ELECTRIQUE, CET APPAREIL NE DOIT PAS ETRE EXPOSE
A LA PLUIE OU A L'HUMIDITE ET AUCUN OBJET REMPLI DE LIQUIDE,
TEL QU'UN VASE, NE DOIT ETRE POSE SUR CELUI-CI. REMPLACER
PAR UN FUSIBLE DE MEME TYPE ET DE 250 VOLTS.
FOR 220-240V OPERATION,
FUSE MUST BE CHANGED
FCC ID: I4S-XRs CAN-ICES-3B/NMB-3B
TO T5AH/250V
230V
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT
TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
115V
RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
FOR 115V OPERATION,
FUSE MUST BE CHANGED
TO T10AH/250V
A PRODUCT OF PEAVEY ELECTRONICS CORP.
DESIGNED AND ENGINEERED IN U.S.A.
MADE IN CHINA
50
51
MAIN
IC: 3642B-XRs
CONNECTORS COMPATIBLE
PINOUT NEG
WITH TWIST-LOCK
CONNECTORS AND 1/4" TWIST-LOCK 1-
SPEAKER CABLE
1/4" SLV
SPEAKER OUTPUTS
MINIMUM LOAD
CLASS 2 WIRING
4 OHMS PER AMPLIFIER
52
MAIN/MONITOR
(WITH FRONT PANEL MONITOR SWITCH ACTIVE
THESE OUTPUTS RECEIVE SIGNAL FROM MONITOR SECTION)
FOOTSWITCH
EFFECTS DEFEAT
53