3585 series hydraulic installation tools (18 pages)
Summary of Contents for Huck ERT1D
Page 1
NSTRUCTION ANUAL BBERT IVET OOL MODELS ERT1D, ERT2D, ERT4D, ERT1DL ERT2DL Form HK 1039 04-16-2004...
Page 3
13. Do not abuse tool by dropping or using it as a 2. Huck equipment must be maintained in a safe hammer. Never use hydraulic or air lines as a working condition at all times and inspected on a handle.
Page 5
This manual contains operating and service procedures for Specific instructions for each tool are given under that tool the Ebbert Rivet Tool models ERT1D, ERT2D, ERT3D, model number heading. While they may appear to be simi- ERT4D, and their optional tool configurations. It is suggest-...
Page 7
Series Tooling Alcoa Fastening Systems ERT D OOL SPECIFICATIONS CONTINUED ERT4D Weight: 3.89 lbs. Stroke: 1-1/32” Rated Pull Force: 4,454 lbs. Fastener Sizes: 1/8” through 1/4” 12.67 321.9 9.81 249.1 3.50 8.73 88.9 221.7 2.00 50.8 INCHES Fig. 1B...
Page 8
Retaining Ring. If it is removed, (Figure 2) when replacing, be sure to relocate the retaining ring 1. Unscrew the two Socket Head Screws for ERT1D or ears at the bottom of the Cylinder, allowing clearance four screws for ERT2D which secure the Piston Rod for the hydraulic inlet port.
Page 9
Secure the End Cap and Support Loop Assembly with cycled. The pulling head assembly can now be two screws (ERT1D) or four screws (ERT2D). installed. 4. At this point, reposition the tool in the vice with the open front of the cylinder pointing straight up.
Page 10
Series Tooling Alcoa Fastening Systems ERT D ERVICE PROCEDURES CONT Disassembly of ERT4D (Figure 3) 6. The Cylinder is now stripped of parts except the Retaining Ring . For normal tool service it is not neces- 1. Remove the Handle from the front of the tool. sary to remove this Retaining Ring.
Page 11
Series Tooling Alcoa Fastening Systems ERT D ERVICE PROCEDURES CONT Reassembly of ERT4D 1. When replacing seals, make sure they are correctly 5. Making sure the cutout section will clear the ears of the positioned as shown on the Tool Schematic. Wipe all Retaining Ring, slide the Front Seal Retainer down, seals with a thin film of seal lubricant before reassem- using care to get it positioned straight in the Cylinder.
Page 12
IVET TOOL HANDLE FUNCTION The rivet tool handle contains the air valve mechanism On models ERT1D and ERT2D the handle is adjustable which, when actuated, initiates the rivet station cycle. through a 20 degree arc. This patented design allows relief...
Page 13
Series Tooling Alcoa Fastening Systems ERT D Fig. 5...
Page 14
Series Tooling Alcoa Fastening Systems ERT D Fig. 6...
Page 15
Series Tooling Alcoa Fastening Systems ERT D Fig. 7 17 (4) 3 4 5 6 7 3 8 9 10 11 12 Torque screws to 12-15 ft/lbs. 18 (2) 19 (4) ERT1DL Return Stroke Pull Stroke 15 (2) Hose (Orange) Hose (Black) Item Part No.
Page 16
Series Tooling Alcoa Fastening Systems ERT D Fig. 9...
Page 17
Series Tooling Alcoa Fastening Systems ERT D ROUBLESHOOTING Always check out the simplest possible cause of a malfunc- Air Bleeding Power Unit and Rivet Tool tion first. For example, an air hose not connected. Then pro- Together ceed logically, eliminating each possible cause until the cause is located.
Page 18
Series Tooling Alcoa Fastening Systems ERT D ITS AND ACCESSORIES Piston Assembly Bullet - 300072 Service Kit ERT1D, ERT1DL -300477 Service Kit ERT2D, ERT2DL -300478 Filler / Bleed Pump Assembly - 300509 ERVICE NOTES...
Page 19
Huck or its sup- THERE ARE NO WARRANTIES WHICH EXTEND pliers.
Page 20
The Future of Assembly Technology, The Future of Tooling to create any warranty, express, implied, or statutory; all warranties Technology, and Tools of Productivity are service marks of Huck are contained only in Huck’s written quotations, acknowledge- International. Huck provides technical assistance regarding the use ments, and/or purchase orders.
Need help?
Do you have a question about the ERT1D and is the answer not in the manual?
Questions and answers