Table Of Contents; Introduction; Recommended Tools & Materials - THUNDER TIGER Sept. Fury Assembly Manual

INTRODUCTION

Congratulations on the purchase of one of our finest ARFs to date. The ever-popular Sept.Fury piloted by Michael Brown
qualified in the Unlimited Class at 468.266 mph of the 2002 National Championships Air Race & Air Show, which was held
in Reno Stead Field. For more information please browse www.septemberpops.com for more information.
Thunder Tiger has teamed up with the Michael Brown Racing team to bring this legendary airplane to your hands; Thunder
Tiger is proudly to present the only officially licensed 1/7th replica of the "Sept.Fury" to all the R/C hobbyist alike worldwide!
It's a replica that has stayed true to the "Sept.Fury" in its purest form, pre-painted fiberglass fuselage and cowl, scale details
like panel line and retract well with gear door, etc. With it, you can now experience the thrill of piloting one of the best racing
planes in the history! Fly it low, fly it fast to experience the ultimate thrill and pylon racing excitement of the "Sept.Fury".
PRE-ASSEMBLY NOTES
The Sept. Fury is designed for advanced pilots and it requires advanced assembling and flying skill. Before you
begin, check the entire contents of your kit against the parts drawing and photos to make sure that no parts are missing
or damaged. This will also help you to become familiar with each component of your plane. If you find that any of the parts
are either missing or damaged, please contact Thunder Tiger Distributors for Customer Service.
Before beginning the assembly read the instructions thoroughly to give an understanding of the sequence of steps and a
general awareness of the recommended assembly procedures.
Trial fit each part before gluing it in place. Make sure you are using the correct part and that it fits well before assembling.
No amount of glue can make up for a poor-fitting part. Always apply Loctite ( not furnished) to all screws and nuts to
prevent them from loosening .

TABLE OF CONTENTS

Introduction................................................2
Recommended Tools & Materials ...............3
Parts Drawings........................................ 4-5
Parts Check List.........................................6
Wing................. ...................................7-10
Landing Gear......................................11-12
Fuselage..................................................13
Tail......................................................14-16
Rudder .......................................................17
Tail Gear ....................................................18
Engine........................................................19
Fuel Tank....................................................20
Radio..........................................................21
Cowling......................................................22
Decal .........................................................23
Balance......................................................24
2
RECOMMENDED TOOLS & MATERIALS
RECOMMENDED TOOLS & MATERIALS
Adhesives:
Instant setting Cyanoacrylate adhesive (thin CA)
Slow setting Cyanoacrylate adhesive (thick CA)
5-10 Minute Epoxy (fast)
20-30 Minute Epoxy (slow)
Tools:
Model knife, T-Pins, MASK tape
Small screwdrivers, medium screwdrivers
Scissors
Steel straight edge
Long nose pliers and diagonal cutting pliers
Drill and drill bits (1/16", 3/32", 3.4mm)
M4x0.7 Tap
Sanding block
Fine felt tip pen and soft lead pencil
Straight building board
R/C System:
6 Channel radio with 7 servos plus one retract servo
Five 12" extension wires.
one Y cords
Engine:
2 cycle:91~1.08
4 cycle:1.2~1.5
Propeller:
Appropriate for engine type and preferred
performance
Adhesives - You will need two types of adhesives for the
Sept.Fury - Epoxy and Instant (cyanoacrylate) adhesives.
We recommend that you purchase both 5-minute and 30-
minute epoxy to cut down on assembly time, but you can
get by with only 30-minute epoxy if time is not important.
You will also need a small bottle of both "Thick" and "Thin"
instant CA adhesive.
Tools - Model assembly can be much easier if the proper
tools are used. Therefore, we have included in our
checklist to the left, a complete listing of all the tools we
used to assemble our prototype models. As you will
notice, many household tools can be utilized during
construction.
Engine-The Thunder Tiger
PRO-91is the ideal engines
for this airplane. This quiet-
running engine is easy to
start, requires no special
break-in periods, easy to
maintain and will last for
years.
Muffler (P/N TTR9791)
Most Pitts style mufflers
will fit this Sept. Fury .
However, we recommend
the use of Thunder Tiger
custom - made Sept. Fury
muffler with two exhaust
pipes that divert the smoke
in to the two concavities of
the fuselage to obtain a
more scale- like apperance.
This muffler fits TT and OS.
60~.90engines.
ITEMS YOU MAY NEED
TTR1115 - Precision Fueler Valve
3