Table of Contents
Advertisement
LOCATION 131: AUTOMATIC BYPASS / INSTANT ARMING
Location 131 is used to enable automatic "Instant Arming". Programming a "1" in this location will cause the control to
automatically enter the "Instant" mode and bypass interior follower zones if a fault is not detected on an entry/exit zone
during the exit delay. Programming a "3" in this location (Automatic Bypass), will cause the interior follower zones to
become bypassed if a fault is not detected on an entry/exit zone, yet will not change the status of the entry/exit zone. If
this location contains a "0", these features are disabled. Pressing the [U] key when the system is armed, will cause the
"Instant" light to toggle. When the "Instant" light is on, the entry/exit zone is instant; when off, the entry/exit zone is
delayed. The [U] key will toggle the "Instant" mode regardless of the programming data in this location. See location 141
"Special Keypad Functions" to further enhance these features.
LOCATION 132: SIREN DRIVER OR VOLTAGE OUTPUT / LAST CHANCE TO EXIT WARNING
The built-in siren driver has a steady sound (for Priority zone type), and a yelp sound (for Burglary and Panic). Factory
default is "0", enabling this feature. If the built-in siren driver is NOT to be used, program a "1" in location 132.
Terminals 14 & 15 will now output 1 Amp at 12VDC. NOTE: Ten seconds prior to the end of the exit delay the keypad
will sound the "Last Chance To Exit" warning (one long beep followed by three short beeps). To disable the "Last
Chance To Exit" warning, add 4 to the Siren Driver/Voltage Output data selected above and program the sum (0 + 4 =
"4" or 1 + 4 = "5") in this location. NOTE: The voltage output shall be used on UL Listed systems.
LOCATION 133: L.E.D. EXTINGUISH FEATURE
Keypad LEDs (with the exception of the A.C. LED) will extinguish after 60 seconds of keypad inactivity, if a "1" is
programmed in location 133. The LEDs will become illuminated immediately upon a keypress or alarm condition.
LOCATION 134: ENTERING THE NUMBER OF DIAL ATTEMPTS
Location 134 is used to enter the number of dial attempts (1 to 15 attempts) the communicator will try for the appropriate
phone number(s) before ending the notification process. If this location contains an "8", the communicator will make
eight attempts to the first number, and then eight attempts to a second number, if a second number is programmed as
backup.
LOCATION 135: POWER UP CONDITION
If a "1" is programmed in location 135, the Ranger 8600E will power-up disarmed if there is a total power shutdown and
battery failure. If a "2" is programmed in this location, it will power up armed. If this location contains a "0", the Ranger
8600E will maintain the condition it was in at power down. A watchdog circuit reset will cause the Ranger 8600E to reset
to the selected condition.
LOCATION 136: POWER UP DELAY
If a "1" is programmed in location 136, the Ranger 8600E will not delay 60 seconds before accepting open or short
inputs from any zone. If a "0" is programmed, sensors on all zones are allowed 60 seconds to stabilize at power-up.
After 60 seconds, the Ranger will once again accept loop opens or shorts as an alarm condition. This 60-second period
will also be initiated after exiting the program mode, or a watchdog circuit reset condition.
LOCATION 137: IMMEDIATE RESTORE BY ZONE
If a "1" is programmed in location 137, restoral signals will follow the restore condition and report restores immediately
after the condition has unfaulted. A non-extended format will not send a restore message until all zones and trouble
conditions have restored. If this location contains a "0", the restore signal or signals will be reported only after siren
timeout.
LOCATION 138: NO ARMING WITH A ZONE BYPASSED
If a "1" is programmed in location 138, the Ranger 8600E will not arm with any zone bypassed. If programmed with a
"0", up to 5 of the 6 burglary zones can be bypassed, and the Ranger 8600E can still be armed. If an "8" is
programmed, it will prevent a beeping if you loose A.C.power and entering of codes twice to stop beeping.
LOCATION 139: PROGRAMMING THE QUICK ARM DIGIT
Location 139 contains the "Quick Arm" digit. To enable, program a digit (1-9) in this location. If the "Quick Arm" digit is
the same as the first digit of the Master code (user 1), the "Chime" feature will not function. The "Quick Arm" digit cannot
be the same as the first digit of the "Go To Program" code. Default is "0", disabled.
16
Hide quick links:
Advertisement
Table of Contents
