Related Manuals for Lincoln Speedtec 180C
Summary of Contents for Lincoln Speedtec 180C
- Page 1 IM3039 8/2015 REV05 SPEEDTEC 180C & 200C OPERATOR’S MANUAL ENGLISH Lincoln Electric Bester Sp. z o.o. ul. Jana III Sobieskiego 19A, 58-263 Bielawa, Poland www.lincolnelectric.eu...
-
Page 2: Declaration Of Conformity
2006/95/CEE, 2004/108/CEE and has been designed in compliance with the following standards: EN 60974-1, EN 60974-5, EN 60974-10:2007 26.07.2012 Paweł Lipiński Operations Director Lincoln Electric Bester Sp. z o.o., ul. Jana III Sobieskiego 19A, 58-263 Bielawa, Poland 12/05 English English... -
Page 3: Table Of Contents
12/05 THANKS! For having chosen the QUALITY of Lincoln Electric products. Please Examine Package and Equipment for Damage. Claims for material damaged in shipment must be notified • immediately to the dealer. For future reference record in the table below your equipment identification information. Model Name, Code & Serial •... -
Page 4: Safety
Failure to follow the instructions in this manual could cause serious personal injury, loss of life, or damage to this equipment. Read and understand the following explanations of the warning symbols. Lincoln Electric is not responsible for damages caused by improper installation, improper care or abnormal operation. -
Page 5: Introduction
The manufacturer reserves the right to make changes and/or improvements in design without upgrade at the same time the operator’s manual. Introduction The welding machines SPEEDTEC 180C enables Driving roll V0.8/V1.0 for solid wire (mounted in the • welding: wire feeder). -
Page 6: Duty Cycle And Overheating
Verify the under the symbol. connection of ground wires from the machine to the input source. The welding machine SPEEDTEC 180C, SPEEDTEC 200C must be connected to a correctly SPEEDTEC 200C: The message as installed plug-in socket with an earth pin. - Page 7 4. Knob Control: Depending on welding process, this 15. Escape Button (right): knob controls: Cancels an action / exit menu. • GMAW Inductance: Arc control is Locks and unlocks knobs and buttons on the panel • process controlled by this knob. If the (press and hold button for 4 seconds).
- Page 8 WARNING Positive (+) polarity is set at the factory. WARNING Before welding check the polarity for using electrodes and wires. If the welding polarity has to be changed, user should: Switch off the machine. • Determine the wire polarity for the wire to be used. •...
- Page 9 Table 2. Loading the Electrode Wire Turning the Allen screw M8 anticlockwise decreases the Turn the machine off. • spring tension and you can decrease the brake torque. Open the side cover of the machine. • Unscrew the locking nut of the sleeve. •...
-
Page 10: Gas Connection
• Welding GMAW, FCAW-SS Process The 2-Step - 4-Step changes the function of the gun’s SPEEDTEC 180C and SPEEDTEC 200C can be used to trigger. welding GMAW and FCAW-SS process. 2 Step trigger operation turns welding on and off in •... - Page 11 Welding SMAW (MMA) Process machine’s software. This value was recalled on the basis of data (input data) had been loaded: SPEEDTEC 180C and SPEEDTEC 200C does not include the electrode holder with lead necessary for SPEEDTEC 200C SMAW welding, but the one can be purchased separately.
- Page 12 Depending on welding machine, the user can set Error’s Message (only SPEEDTEC functions: 200C) Contact with the Technical Service Center or Lincoln SPEEDTEC 180C Electric, when a machine’s display of SPEEDTEC 200C The welding current will show a message of the Figure 7 or similar.
- Page 13 Guide’s Marking Interface SPEEDTEC 200C Description of the user interface in "Quick Guide" chapter Select Welding Process SMAW (MMA) Welding Basic menu GMAW (MIG/MAG) Burnback Brightness Level Manual Welding View Software and FCAW- Self shielded Run-in WFS Hardware Version Manual Welding Information GMAW (MIG/MAG) Preflow Time...
- Page 14 WARNING For any repair operations, modifications or maintenances, it is recommended to contact the nearest Technical Service Center or Lincoln Electric. Repairs and modifications performed by unauthorized service or personnel will cause, that the manufacturer’s warranty will become null and void.
-
Page 15: Electromagnetic Compatibility (Emc)
Lincoln Electric. Before installing the machine, the operator must check the work area for any devices that may malfunction because of electromagnetic disturbances. -
Page 16: Technical Specifications
Technical Specifications NAME INDEX SPEEDTEC 180C K14098-1 SPEEDTEC 200C K14099-1 INPUT Input Voltage U EMC Group / Class Frequency 180C 230V ± 10% II / A 50 / 60 Hz 200C 1-faza Input Power at Rated Cycle Input Amperes I cos φ... -
Page 17: Weee
Spare Parts 12/05 Part list reading instructions Do not use this part list for a machine if its code number is not listed. Contact the Lincoln Electric Service • Department for any code number not listed. Use the illustration of assembly page and the table below to determine where the part is located for your particular •... -
Page 18: Accessories
Accessories K10413-15-3M The gas-cooled gun LG150 to GMAW process - 3m. KP10461-1 Gas nozzle conical Ø12mm. KP10440-06 Contact Tip M6x25mm ECu 0.6mm KP10440-08 Contact Tip M6x25mm ECu 0.8mm KP10440-09 Contact Tip M6x25mm ECu 0.9mm KP10440-10 Contact Tip M6x25mm ECu 1.0mm KP10440-10A Contact Tip M6x25mm Al 1.0mm KP10468...