Servicing Notes - Sony HCD-HDX285 Service Manual

HCD-HDX285/HDX287WC/HDX585/HDX587WC/HDX589W/HDX685/HDX686W
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostat-
ic break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
RELEASING THE TRAY LOCK
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Releasing Procedure:
1. Press the [ ] button to turn on the system.
?/1
2. Press the [FUNCTION] button repeatedly to select "DVD".
3. While pressing the [ ] button, press the [
x
LOCKED" displayed on the fl uorescent indicator tube (around
5 seconds).
Note: When "LOCKED" is displayed, the tray lock is not released by
turning power on/off with the [ ? / 1 ] button.
RELEASING THE DEMO PLAY LOCK
Releasing Procedure:
1. Press the [ ] button to turn on the system.
?/1
2. Press the [FUNCTION] button repeatedly to select "DVD".
3. While pressing the [ ] button, press the [
x
"DEMO OFF" displayed on the fl uorescent indicator tube
(around 5 seconds).
Note: When "DEMO ON" is displayed, the set is not possible to turn off
the system.
SECTION 1

SERVICING NOTES

NOTE OF REPLACING THE IC1103 ON THE MAIN
BOARD
IC1103 on the MAIN board cannot exchange with single. When
this part is damaged, exchange the entire mounted board.
MODEL IDENTIFICATION
HDX585
HDX686W
HDX685
HDX287WC
HDX587WC
HDX589W
HDX285: US model
HDX285: 240V AC area in E model
HDX285: Saudi Arabia model
FL-JACK AND P-SW BOARDS DISCRIMINATION
In this set, the FL-JACK and P-SW boards have been changed in
the midway of production. Repair after distinguishing each type
set to doing the repair referring to following.
– FL-JACK Board (Component Side) –
– P-SW Board (Component Side) –
] button until "UN-
Z
] button until
N
SPEAKER
FRONT R FRONT L SUR R SUR L
SPEAKER TV
DIGITAL IN
HDMI OUT
DMPORT
DC5V
0.7A MAX
CENTER SUBWOOFER OPTICAL COAXIAL
Model
Suffix-11 : 1-878-158-11
Suffix-12 : 1-878-158-12
Suffix-11 : 1-878-159-11
Suffix-12 : 1-878-159-12
ANTENNA
EZW-T100
FM AM
COAXIAL 75
COMPONENT VIDEO OUT VIDEO TV/VIDEO
OUT
Y P B /C B P R /C R R AUDIO IN L
PART No.
Part No.
4-120-917-0[]
4-120-917-1[]
4-120-917-2[]
4-120-917-3[]
4-120-917-4[]
4-120-917-5[]
4-120-917-6[]
4-120-917-8[]
4-120-917-9[]
5