Titan LX-80 II Instruction Sheet

Instruction Sheet

Important Safety Instructions

Indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
a) SAVE THESE INSTRUCTIONS – To reduce the risks of fire or
explosion, electrical shock, and the injury to persons, read and
understand all instructions included in this manual. Be familiar
with the controls and the proper usage of the equipment.
b) WARNING - To reduce the risk of fire or
explosion:
1. Do not spray flammable or combustible materials
near an open flame, pilot lights or sources of ignition
such as hot objects, cigarettes, motors, electrical equipment and
electrical appliances. Avoid creating sparks from connecting and
disconnecting power cords.
2. Use extreme caution when using materials with a flashpoint below
70ºF (21ºC). Flashpoint is the temperature that a fluid can produce
enough vapors to ignite.
3. Paint or solvent flowing through the equipment is able to result in
static electricity. Static electricity creates a risk of fire or explosion in
the presence of paint or solvent fumes. All parts of the spray system,
including the pump, hose assembly, spray gun and objects in and
around the spray area shall be properly grounded to protect against
static discharge and sparks. Use only conductive or grounded high-
pressure airless paint sprayer hoses specified by the manufacturer.
4. Verify that all containers and collection systems are grounded to
prevent static discharge.
5. Connect to a grounded outlet and use grounded extension cords
(electric models only). Do not use a 3 to 2 adapter.
6. Do not use a paint or solvent containing halogenated hydrocarbons.
Such as chlorine, bleach mildewcide, methylene chloride and
trichloroethane. They are not compatible with aluminum. Contact the
coating supplier about compatibility of material with aluminum.
7. Keep spray area well ventilated. Keep a good supply of fresh air
moving through the area to keep the air within the spray area free
from accumulation of flammable vapors. Keep pump assembly in well
ventilated area. Do not spray pump assembly.
8. Do not smoke in the spray area.
9. Do not operate light switches, engines, or similar spark producing
products in the spray area.
10. Keep area clean and free of paint or solvent containers, rags, and
other flammable materials.
11. Know the contents of the paint and solvents being sprayed. Read
all Material Safety Data Sheets (MSDS) and container labels
provided with the paints and solvents. Follow the paint and solvent
manufacture's safety instructions.
12. Place pump at least 25 feet (7.62 meters) from the spray object in a
well ventilated area (add more hose if necessary). Flammable vapors
are often heavier than air. Floor area must be extremely well ventilated.
The pump contains arcing parts that emit sparks and can ignite vapors.
13. Plastic can cause static sparks. Never hang plastic to enclose spray
area. Do not use plastic drop cloths when spraying flammable
material.
14. Fire extinguisher equipment shall be present and working.
c) WARNING - To reduce the risk of skin injection:
1. Do not aim the gun at, or spray any person or animal.
2. Keep hands and other body parts away from the discharge.
For example, do not try to stop leaks with any part of the body.
3. Always use the nozzle tip guard. Do not spray without the nozzle tip
guard in place.
4. Only use a nozzle tip specified by the manufacturer.
5. Use caution when cleaning and changing nozzle tips. In the case
where the nozzle tip clogs while spraying, ALWAYS lock gun trigger,
shut pump off, and release all pressure before servicing, cleaning tip
or guard, or changing tip. Pressure will not be released by turning off
the motor. The PRIME/SPRAY valve or pressure bleed valve must be
© Titan Tool Inc. All rights reserved.
High Pressure Spray Gun with TR
Form No. 0286942B
0711 •
LX-80 II
turned to their appropriate positions to relieve system pressure. Refer
to PRESSURE RELIEF PROCEDURE described in the pump manual.
6. Do not leave the unit energized or under pressure while unattended.
When the unit is not in use, turn off the unit and relieve the pressure in
accordance with the manufacturer's instructions.
7. High-pressure spray is able to inject toxins into the body and cause
serious bodily injury. In the event that injection occurs, seek medical
attention immediately.
8. Check hoses and parts for signs of damage, a leak can inject material
into the skin. Inspect hose before each use. Replace any damaged
hoses or parts.
9. This system is capable of producing 3600 PSI / 248 Bar. Only
use replacement parts or accessories that are specified by the
manufacturer and that are rated a minimum of 3600 PSI. This includes
spray tips, nozzle guards, guns, extensions, fittings, and hose.
10. Always engage the trigger lock when not spraying. Verify the trigger
lock is functioning properly.
11. Verify that all connections are secure before operating the unit.
12. Know how to stop the unit and bleed pressure quickly. Be thoroughly
familiar with the controls. Pressure will not be released by turning off
the motor. The PRIME/SPRAY valve or pressure bleed valve must be
turned to their appropriate positions to relieve system pressure. Refer
to PRESSURE RELIEF PROCEDURE described in the pump manual.
13. Always remove the spray tip before flushing or cleaning the system.
NOTE TO PHYSICIAN:
Injection into the skin is a traumatic injury. It is important to
treat the injury as soon as possible. DO NOT delay treatment
to research toxicity. Toxicity is a concern with some coatings
injected directly into the blood stream. Consultation with a plastic
surgeon or reconstructive hand surgeon may be advisable.
d) WARNING - To reduce the risk of injury:
1. Always wear appropriate gloves, eye protection, clothing and a
respirator or mask when painting. Hazardous vapors – Paints,
solvents, insecticides, and other materials can be harmful if inhaled or
come in contact with body. Vapors can cause severe nausea, fainting
or poisoning.
2. Do not operate or spray near children. Keep children away from
equipment at all times.
3. Do not overreach or stand on an unstable support. Keep effective
footing and balance at all times.
4. Stay alert and watch what you are doing.
5. Do not operate the unit when fatigued or under the influence of drugs
or alcohol.
6. Do not kink or over-bend the hose. Airless hose can develop leaks
from wear, kinking and abuse. A leak can inject material into the skin.
7. Do not expose the hose to temperatures or pressures in excess of
those specified by manufacturer.
8. Do not use the hose as a strength member to pull or lift the equipment.
9. Use lowest possible pressure to flush equipment.
10. Follow all appropriate local, state and national codes governing
ventilation, fire prevention and operation.
11. The United States Government Safety Standards have been adopted
under the Occupational Safety and Health Act (OSHA). These
standards, particularly part 1910 of the General Standards and part
1926 of the Construction Standards should be consulted.
12. Before each use, check all hoses for cuts, leaks, abrasion or bulging
of cover. Check for damage or movement of couplings. Immediately
replace hose if any of those conditions exist. Never repair a paint hose.
Replace with a conductive high-pressure hose.
13. Do not spray outdoors on windy days.
14. Always unplug cord from outlet before working on equipment (electric
models only).
1
2

Spray Tip

English