Operation - Titan LX-80 II Instruction Sheet

Using the Gun Trigger Lock
Always engage the gun's
trigger lock when the gun is
not in use.
1. To lock the trigger,
rotate the trigger lock
forward until it stops.
2. To unlock the trigger,
rotate the trigger lock
backward until it is Trigger locked
vertical.
(gun will not spray)
Setup
Never attempt to assemble, change, or clean the gun, tip,
or tip guard without first relieving pressure from the spray
system. Follow the "Pressure Relief Procedure" in the
sprayer's Owner's Manual.
Always use a tip safety guard for added protection against
injection. Beware that the guard alone will not prevent
injection. Never cut off tip guard! Always engage gun
trigger lock when the gun is not in use. Before servicing
equipment, consult Owner's Manuals and follow all
warnings.
1. Set up the sprayer. Refer to the instructions in the sprayer's
Owner's Manual.
2. Attach a grounded, airless spray hose to the material inlet on the
gun. Using two wrenches (one on the gun and one on the hose),
tighten securely.
3. With the tip and tip guard off the gun, start the sprayer. Flush
and prepare the spray system according to the sprayer's Owner's
Manual. Inspect the spray system to make sure that all fittings
are secure and that there are no leaks.
4. Perform the "Pressure Relief Procedure" described in the
sprayer's Owner's Manual.
Assembling the TR
1. Place the holder for the TR
the holder over the spray guard.
2. Secure the holder by placing the collar on as shown.
3. Line up the tabs (a) on the spray tip with the slots (b) in the
holder. Slide the tip into the guard.
1 2
4. Thread the tip guard onto the
gun. Position the tip guard in
the desired spraying position,
then tighten securely by hand.

Operation

1. Rotate the spray tip forward to
one of the SPRAY positions.
Narrow
2. Start the sprayer. Refer to the instructions in the sprayer's
Owner's Manual.
3. Adjust the fluid pressure on the sprayer until the spray is
completely atomized. Always spray at the lowest pressure
necessary to get the desired results.
English
Trigger unlocked
(gun will spray)
Spray Tip
2
2
nozzle onto your spray guard. Close
3
b
Wide
NOTE: The spray tip determines the size of spray pattern
and coverage. When more coverage is needed, use a
larger tip instead of increasing fluid pressure.
4. To clear a clogged tip:
a. Rotate the tip 180º from its current position.
b. Trigger the gun once so that the pressure can blow the clog
out.
IMPORTANT: Never pull the trigger more than once at time with the
tip in the reverse position.
c. Continue this procedure until the tip is clear of the clog.
Changing a Tip
Tips can be removed and replaced easily without disassembling the gun.
Never attempt to change or clean the tip or tip guard
without first performing the "Pressure Relief Procedure."
1. Perform the "Pressure Relief Procedure" described in the
sprayer's Owner's Manual.
2. Remove the tip from the slot on the tip guard.
3. Insert the new tip into the slot on the tip guard. Rotate the spray
tip forward to one of the SPRAY positions.
Tip
guard
Identifying Tip Sizes
To identify tip sizes, use the following formula. A "515 " tip size will be
used in this example.
The first digit multiplied by two represents the size of the spray pattern
when spraying 12" away from the work surface:
5 x 2 = 10" spray pattern
The second two digits represent the diameter of the orifice on the tip:
a
15 = .015" orifice
The narrow pattern tip is approximately 1/3 the width of the wider tip, and
is ideal for trim work or any other surfaces that would require a narrow,
more precise spray pattern.
The wider pattern tip is ideal for spraying large surfaces in a short amount
of time.
NOTE: Worn spray tips will adversely affect the spray pattern
and result in reduced production, poor finish, and
wasted material. Replace worn tips immediately.
2
Tip
holder
Tip
© Titan Tool Inc. All rights reserved.