Operation Manual AV Receiver/DVD Player with 6.5 inch Wide Display AVH-P5750DVD English...
Contents Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, keep this man- ual in a safe place for future reference.
Contents PBC playback 37 Using disc title functions 52 Introduction of advanced Video CD Selecting tracks from the track title list 53 operation 38 Using compression and bass emphasis 53 Repeating play 38 TV tuner Selecting audio output 38 Watching the television 54 Playing CDs Storing and recalling broadcast stations 55 Listening to a CD 39...
Contents Adjusting source levels 66 Setting the illumination switch 85 Compensating for equalizer curves (EQ- Setting the rear output and subwoofer EX) 66 controller 85 Correcting distorted sound 86 Digital Signal Processor Switching the sound muting/attenuation 86 Introduction of DSP adjustments 67 Mixing AVG-VDP1 beep and audio sound 87 Using the sound field control 68 Resetting the audio functions 87...
Section Precautions IMPORTANT SAFEGUARDS WARNING Please read all of these instructions regarding ! Do not attempt to install or service your your display and retain them for future refer- display by yourself. Installation or servi- ence. cing of the display by persons without 1 Read this manual fully and carefully be- training and experience in electronic fore operating your display.
Section Precautions When you attempt to watch a DVD, Video CD or TV while driving, the warning VIDEO VIEW- ING IS NOT AVAILABLE WHILE DRIVING will appear on the front display. To watch a DVD, Video CD or TV on the front display, park your vehicle in a safe place and apply the parking brake.
! If this unit does not operate properly, contact your dealer or nearest authorized Pioneer Ser- DVD video disc region numbers vice Station. DVD video discs that have incompatible region numbers cannot be played on this player.
Section Before You Start The illustration below shows the regions and DVD video playback corresponding region numbers. It is possible to play back DVD video, DVD-R (video mode) and DVD-RW (video mode). Remember that use of this system for com- mercial or public viewing purposes may con- stitute an infringement on the authors rights protected by the Copyright Law.
Macrovision Corporation. Reverse engineering or disassembly is prohibited. iPod compatibility When you use this unit with a Pioneer iPod adapter (CD-IB100), you can control an iPod, About WMA iPod mini, iPod Photo. ! iPod is a trademark of Apple Computer, ®...
Section Before You Start What the marks on DVDs Microsoft, Windows Media, and the Windows logo are trademarks, or registered trademarks indicate of Microsoft Corporation in the United States The marks below may be found on DVD disc and/or other countries. labels and packages.
! Do not handle the battery with metallic tools. Notes ! Do not store the battery with metallic materi- ! When using with a Pioneer Vehicle Dynamics als. Processor, if you press RESET, be sure ACC ! In the event of battery leakage, wipe the re- OFF is selected.
Section Whats What Head unit 6 ENTERTAINMENT (ENT) button Press to switch between the background 1 INFO button displays. Press to turn the information bar on/off. 7 WIDE button 2 PGM button Press to select a desired mode for enlarging Press to operate the preprogrammed func- a 4:3 picture to a 16:9 one.
Section Whats What c BOOKMARK (BM) button Press to bookmark a scene that you want to resume playback. d BAND/ESC button Press to select among three FM bands and one AM band and to cancel the control mode of functions. e EQ button Press to select various equalizer curves.
Section Whats What Remote control For details, refer to Using the remote control operation mode switch on page 16. 1 Remote control selection switch Switch to change the setting of the remote 7 BOOKMARK (BOOK.M) button control. For details, refer to Setting remote AVH mode: Press to operate the prepro- control code type on page 83.
Section Whats What 9 BAND/ESC button tuner or disc number search for the multi- AVH mode: Press to select among three FM CD player. bands and one AM band and to cancel the DVD mode: Press to directly select the de- control mode of functions.
ENTERTAINMENT (ENT). Using the remote control TV mode operation operation mode switch TV operations available with a Pioneer TV tuner There are three remote control operation (e.g. GEX-P5750TV(P)) can be controled with modes on the remote control. AVH mode. TV mode is not used with this unit.
When the AV (AV input) is not set to VIDEO (refer to page 88). % When using the touch panel keys, ! External unit refers to a Pioneer product (such touch the source icon and then touch the as one available in the future) that, although desired source name.
! V.D.P. Display the AVG-VDP1 on rear dis- play Adjusting the volume Note When a Pioneer Vehicle Dynamics Processor % Use VOLUME to adjust the sound level. (AVG-VDP1) is connected to this unit, the AVG- With the head unit, press VOLUME up/+ or VDP1 can be displayed on the rear display.
Section Basic Operations Touch panel key basic ! You can operate this function only when a Pioneer Vehicle Dynamics Processor (AVG- operation VDP1) is connected to this unit. Activating the touch panel keys Dsiplaying AVG-VDP1 % Press V.ADJ to switch the display to the AVG-VDP1.
Section Basic Operations Operating the menu Note If you do not operate the function within about 30 seconds, the display is automatically returned to the playback display. Opening and closing the LCD panel The LCD panel will be opened or closed auto- matically with the turning of the ignition 1 FUNCTION key switch on or off.
Section Basic Operations Adjusting the LCD panel angle Changing the wide screen mode Important You can select a desired mode for enlarging a ! If you can hear the LCD panel knocking 4:3 picture to a 16:9 one. against your vehicles console or dashboard, press ANGLE () to move the LCD panel a lit- % Press WIDE to select the desired set- tle forward.
Section Basic Operations ! CONTRAST Adjust the contrast Notes ! COLOR Adjust the color saturation ! Different settings can be memorized for each ! HUE Adjust the tone of color (red is em- video source. phasized or green is emphasized) ! When video is viewed in a wide screen mode ! DIMMER Adjust the brightness of display that does not match its original aspect ratio, it...
Section Basic Operations Removing the front panel ! Blue moon Adjust the brightness for dark ambient light (nighttime) % Push the release button downward and release the front panel. Touch c or d to adjust the brightness. Take care not to grip it too tightly or to drop Each time you touch c or d moves the key to- the front panel and protect it from contact wards the left or the right.
Section Tuner Listening to the radio Touch the screen to display the touch panel keys. Touch BAND to select a band. Touch BAND repeatedly until the desired band is displayed, FM1, FM2, FM3 for FM or AM. To select a preset channel, touch a pre- set channel on the list.
Section Tuner Storing and recalling Introduction of advanced broadcast frequencies tuner operation If you touch any of the preset tuning keys P1P6 you can easily store up to six broad- cast frequencies for later recall with the touch of a key. % When you find a frequency that you want to store in memory keep touching one of preset tuning keys P1P6 until the...
Section Tuner Touch c or d to set the sensitivity. There are four levels of sensitivity for FM and two levels for AM: FM: 1234 AM: 12 The 4 setting allows reception of only the strongest stations, while lower settings let you receive progressively weaker stations.
Section Playing DVD video discs Watching a DVD video 7 Subtitle language indicator Shows which subtitle language has been selected. 8 Audio language indicator Shows which audio language has been se- lected. Touch the source icon and then touch DVD to select the DVD player. # When the source icon is not displayed, you can display it by touching the screen.
Section Playing DVD video discs Touch d until 10key appears in the dis- # Fast forward/fast reverse may not be possible at certain locations on some discs. If this hap- play. pens, normal playback automatically resumes. Touch 10key. Note Touch 0-9 corresponding to a menu If you do not use the touch panel keys within 30 number and then touch ENTER to start seconds, they will be hidden automatically.
Section Playing DVD video discs % Touch f during playback. Touch q or r to adjust playback The icon e is displayed and playback is speed during slow motion playback. paused, letting you view a still image. Each time you touch q or r it changes the speed in four steps in the following order: # To resume playback at the same point that you 1/161/81/41/2...
Section Playing DVD video discs ! To select 10, touch 1 and 0 in that order. DVD. (Refer to Using the remote control operation ! To select 23, touch 2 and 3 in that order. mode switch on page 16.) For time (time search) ! To select 21 minutes 43 seconds, touch 2, 1, 4 and 3 in that order.
Section Playing DVD video discs Changing the subtitle ! Touching AUDIO during fast forward/fast re- verse, pause or slow motion playback returns language during playback you to normal playback. (Multi-subtitle) With DVDs featuring multi-subtitle recordings, you can switch between subtitle languages during playback.
Section Playing DVD video discs Automatic playback of DVDs ! During playback of a scene shot from mul- tiple angles, the angle icon is dis- When a DVDs disc with DVD menu is inserted, played. Turn angle icon display on or off this unit will cancel the DVD menu automati- using DVD SETUP.
Section Playing DVD video discs Introduction of advanced % Touch REPEAT on the function menu to select the repeat range. DVD video operation ! TITLE Repeat just the current title ! CHPTR Repeat just the current chapter ! DISC Play through the current disc Note If you perform chapter search or fast forward/re- verse, the repeat play range changes to DISC.
Section Playing DVD video discs % During playback, press BOOKMARK (BM) button at the point you want to resume playback next time. The selected scene will be bookmarked so that playback resumes from that point next time. You can bookmark up to five discs. After that, the oldest bookmark is replaced by the new one.
Section Playing Video CDs Watching a Video CD Touch the screen to display the touch panel keys. Touch 10key and then touch 0-9 to se- lect the desired menu item. Playback starts from the selected menu item. # When the menu is two or more pages long, touch o or p to switch between displays.
Section Playing Video CDs Stopping playback Slow motion playback This lets you slow down playback speed. % Touch g. # When you stop Video CD playback (during Keep touching r until is displayed PBC playback only) by touching g, that location during playback.
Section Playing Video CDs Touch d until SEARCH appears in the # You can display the menu by touching display. RETURN during PBC playback. For details, refer to the instructions provided with the disc. Touch SEARCH. Notes Touch TRACK (track) or TIME (time). ! PBC playback of Video-CD cannot be can- celled.
Section Playing Video CDs Introduction of advanced % Touch REPEAT on the function menu to select the repeat range. Video CD operation ! TRACK Repeat just the current track ! DISC Repeat the current disc Note If you perform track search or fast forward/re- verse, the repeat play range changes to DISC.
Section Playing CDs Listening to a CD # If no disc is loaded in the unit, you cannot se- lect DVD (DVD player). Insert a disc in the unit. (Refer to page 17.) Touch the screen to display the touch panel keys.
Section Playing CDs Pausing CD playback Displaying titles on CD TEXT discs % Touch DISP. Pause lets you temporarily stop disc playback. Touch DISP repeatedly to switch between the following settings: % Touch f during playback. D.Title (disc title)D.Artist (disc artist name) PAUSE appears in the display.
Section Playing CDs Introduction of advanced ! DISC Repeat the current disc CD operation Notes ! If you perform track search or fast forward/re- verse, repeat play is automatically cancelled. ! When playing discs with MP3/WMA files and audio data (CD-DA), repeat play performs within the currently playing data type even if DISC is selected.
Section Playing CDs Entering disc titles Touch d to move the cursor to the next character position. You can input CD titles and display the title. When the desired letter is displayed, touch d The next time you insert a CD for which you to move the cursor to the next position and have entered a title, the title of that CD will be then select the next letter.
Section Playing MP3/WMA Listening to MP3/WMA 7 Repeat indicator Shows the selected repeat range. Touch the source icon and then touch DVD to select the DVD player. # When the source icon is not displayed, you can display it by touching the screen. # If no disc is loaded in the unit, you cannot se- lect DVD (DVD player).
Section Playing MP3/WMA # To return to folder 001 (ROOT), press and hold those tracks is displayed on the information BAND/ESC. However, if folder 001 (ROOT) con- bar when it plays back. tains no files, playback commences with folder ! If the inserted disc contains WMA files that 002.
Section Playing MP3/WMA Displaying the list of played even after switching to bit rate. (VBR will be displayed.) information on MP3/WMA file # If specific information has not been recorded Information recorded on a MP3/WMA disc on an MP3/WMA disc, NO XXXX will be dis- can be displayed.
Section Playing MP3/WMA Introduction of advanced % Touch REPEAT on the function menu to select the repeat range. built-in DVD player (MP3/ ! FOLDER Repeat the current folder WMA) operation ! TRACK Repeat just the current track ! DISC Repeat all tracks Notes ! If you select another folder during repeat play, the repeat play range changes to DISC.
Section Playing MP3/WMA Scanning folders and tracks While you are using FOLDER, the beginning of each track in the selected folder plays for about 10 seconds. When you are using DISC, the beginning of the first track of each folder is played for about 10 seconds.
Section Multi-CD Player Listening to a CD Touch a disc title on the list to play back. Operable disc titles are highlighted. If you want to select a disc located at 7 to 12, touch to display 0712. # When the disc titles of 01-06 or 07-12 are not displayed, you can display them by touching LIST.
Section Multi-CD Player % Touch f during playback. % Keep touching DISP until the title be- PAUSE appears in the display. Play of the cur- gins to scroll to the left. rent track pauses. The rest of the title will appear in the dis- play.
Section Multi-CD Player Introduction of advanced peat), TRACK (one-track repeat) and DISC (disc repeat). multi-CD player operation % Touch REPEAT on the function menu to select the repeat range. ! M-CD Repeat all discs in the multi-CD player ! TRACK Repeat just the current track ! DISC Repeat the current disc Notes ! If you select other discs during repeat play,...
Section Multi-CD Player Scanning CDs and tracks Play a CD that you want to program. Touch a or b to select the CD. While you are using DISC, the beginning of each track on the selected disc plays for about Touch NEXT on the function menu.
Section Multi-CD Player Erasing a track from your ITS Touch CLEARb to erase all tracks on the currently playing CD from your ITS playlist. playlist ITS CLEAR is displayed and all tracks on the When you want to delete a track from your ITS currently playing CD are erased from your playlist, you can if ITS play is on.
Section Multi-CD Player Selecting tracks from the Touch a or b to select a letter of the al- phabet. track title list Each time you touch a it will display a letter of Track title list lets you see the list of track titles the alphabet in A B C ...
Section TV tuner Watching the television Touch the source icon and then touch TV to select the TV. # When the source icon is not displayed, you can display it by touching the screen. Touch the screen to display the touch panel keys.
Section TV tuner Storing and recalling Introduction of advanced broadcast stations TV tuner operation If you touch any of the preset tuning keys P01P12 you can easily store up to 12 broad- cast stations for later recall with the touch of a key.
Section TV tuner Storing the strongest broadcast stations sequentially % Touch BSSM on the function menu to turn BSSM on. BSSM begins to flash. While BSSM is flashing the 12 strongest broadcast stations will be stored in order from the lowest channel up. When finished, BSSM disappears.
Section DVD Player Playing a disc 5 Chapter/track number indicator Shows the chapter/track currently playing. 6 Play time indicator Shows the elapsed playing time of the cur- rent chapter/track. 7 Disc list display Shows the disc title list. Touch the source icon and then touch S-DVD to select the DVD player.
Section DVD Player Selecting a disc Introduction of advanced DVD player operation ! You can operate this function only when a multi-DVD player is connected to this unit. % Touch a disc title on the list to play back. Operable disc titles are highlighted. # When the list of titles is not displayed, touch LIST.
Section DVD Player % Touch REPEAT on the function menu to Note select the repeat range. After scanning of a CD is finished, normal play- During DVD video playback back of the tracks will begin again. ! TITLE Repeat just the current title ! CHPTR Repeat just the current chapter ! DISC Repeat the current disc During Video CD or CD playback...
Section Playing songs on iPod Listening to songs on your Touch the screen to display the touch panel keys. iPod To skip back or forward to another song, touch o or p. Touching p skips to the start of the next song.
Section Playing songs on iPod Repeating play # To return to the previous group of list titles, touch For playback of the songs on the iPod, there # To return to the previous menu, touch are two repeat play ranges: TRACK (repeat # To go to the top menu of the list search, touch one song) and ALL (repeat all songs in the TOP.
Section Audio Adjustments Introduction of audio SUB WOOFER. (Refer to Setting the rear output and subwoofer controller on page 85.) adjustments # When selecting the FM tuner as the source, you cannot switch to SLA. # To return to the previous display, touch BACK. # To return to the display of each source, touch ESC.
Section Audio Adjustments Touch c or d to adjust left/right speak- % Press EQ to select the equalizer. er balance. Press EQ repeatedly to switch between the fol- Each time you touch c or d it moves the left/ lowing equalizers: right speaker balance towards the left or the POWERFULNATURALVOCALCUSTOM right.
Section Audio Adjustments +6 6 is displayed as the level is increased Touch a or b to adjust the bass level. or decreased. Each time you touch a or b increases or de- creases the bass level. +6 6 is displayed as Touch b and then touch c or d to se- the level is increased or decreased.
Section Audio Adjustments Using nonfading output Touch c or d to select a desired level. Each time you touch c or d selects level in When the nonfading output setting is on, the the following order: audio signal does not pass through this units LOW (low)MID (mid)HIGH (high) low pass filter (for the subwoofer), but is out- putted through the RCA output.
Section Audio Adjustments Touch c or d to select cut-off fre- ! External unit 1 and external unit 2 are set to quency. the same source level adjustment volume Each time you touch c or d selects cut-off fre- automatically. quencies in the following order: ! AUX (auxiliary input) and AV (AV input) are set 50Hz80Hz125Hz...
Section Digital Signal Processor Introduction of DSP # To go to the next group of function names, touch NEXT. adjustments # To return to the previous group of function names, touch PREV. # When playing discs recorded with more than 96 kHz sampling frequency, you cannot use audio functions.
Section Digital Signal Processor Using the sound field control Using the position selector The SFC function creates the sensation of a One way to assure a more natural sound is to live performance. accurately position the stereo image, putting ! The acoustics of different performance en- you right in the center of the sound field.
Section Digital Signal Processor Using balance adjustment Press a or b to adjust the source vo- lume. You can select a fader/balance setting that Each time you press a or b it increases or de- provides an ideal listening environment in all creases the source volume.
Section Digital Signal Processor Using the dynamic range Using the direct control control You can override audio settings to check for ef- fectiveness of your audio settings. The dynamic range refers to the difference be- ! All audio functions are locked out when the tween the largest and softest sounds.
Section Digital Signal Processor Adjusting the Music mode Touch b and then touch c or d to ad- just the center image. You can adjust the Music mode with the fol- Each time you touch c or d it gradually lowing three controls.
Section Digital Signal Processor Touch c or d to select the correct size select reverse phase and REVERSE appears in for the selected speaker. the display. Each time you touch c or d selects the size in the following order: Note OFF (off)SMALL (small)LARGE (large) When playing a 2-channel mono source with Pro...
Section Digital Signal Processor Adjusting the speaker Note output levels Selecting a cross-over frequency is to set a cross- over frequency of the subwoofers L.P .F. (low-pass You can readjust the speaker output levels filter) and that of the SMALL speaker H.P.F. (high- using a test tone while listening to music.
Section Digital Signal Processor Adjusting the speaker output put levels at SP LEVEL. Both provide the same results. levels using a test tone A convenient test tone allows you to easily get the overall balance right among the speakers. Using the time alignment Touch NEXT on the DSP function menu.
Section Digital Signal Processor Touch TIME ALIGN and then touch Display Equalizer curve ADJUST. FLAT Flat # You cannot select ADJUST when neither FRONT-L nor FRONT-R is selected in CUSTOM1 Custom 1 POSITION (POSI). CUSTOM2 Custom 2 SUPER BASS Super bass Touch a or b to select the speaker to be adjusted.
Section Digital Signal Processor ! The center speaker largely determines the 1.6kHz2kHz2.5kHz3.15kHz4kHz sound image and getting the balance right 5kHz6.3kHz8kHz10kHz12.5kHz isnt easy. We recommend reproducing a 2- Touch b and then touch c or d to ad- ch. audio (a CD for example) and getting just the equalizer level.
Section Digital Signal Processor Auto TA and EQ (auto-time Before operating the auto TA and EQ function alignment and auto- ! Carry out auto TA and EQ in as quiet a equalizing) place as possible, with the car engine and Only when the multi-channel processor (e.g., air conditioning switched off.
Section Digital Signal Processor ! Auto TA and EQ changes the audio settings # Press SOURCE to turn the source on if this as below: unit is turned off. The fader/balance settings return to the Select the position for the seat on center position.
Section Digital Signal Processor # To cancel auto TA and EQ part way through, touch BACK or ESC. 10 When auto TA and EQ is completed, Complete is displayed. When correct measurement of car interior acoustic characteristics is not possible, an error message is displayed.
Section Setting up the DVD player Introduction of DVD setup Setting the subtitle language adjustments You can set a desired subtitle language. If the selected subtitle language is recorded on the DVD, subtitles are displayed in that language. Touch SETUP and LANGUAGE and then touch SUB.
Section Setting up the DVD player Setting the audio language Touch the desired language. The menu language is set. You can set the preferred audio language. # If you have selected OTHERS, refer to When you select OTHERS on the previous page. Touch SETUP and LANGUAGE and then touch AUDIO LANG.
Section Setting up the DVD player Setting the aspect ratio ! When you set a parental lock level and then play a disc featuring parental lock, code There are two kinds of display. A wide screen number input indications may be dis- display has a width-to-height ratio (TV aspect) played.
When the remote control operation switch is set to DVD, changing the remote control code type enables you to operate the Pioneer DVD player with the supplied remote control. There are three remote codes, code type A, code...
Section Initial Settings Adjusting initial settings Setting the FM tuning step The FM tuning step employed by seek tuning can be switched between 100 kHz, the preset step, and 50 kHz. % Touch FMSTEP on the initial menu to se- lect the FM tuning step.
Section Initial Settings % Touch D. WARN on the initial menu to Note turn warning tone on. Never set the illumination switch on if the vehicle # To turn warning tone off, touch D. WARN does not have the ACC position. It may cause bat- again.
Section Initial Settings Switching the sound Touch c or d to switch the subwoofer output or non fading output. muting/attenuation Touch c to select subwoofer output and Sound from this system is muted or attenu- SUB.W appears in the display. Touch d to se- ated automatically when the signal from the lect non fading output and FULL appears in equipment with mute function is received.
When this unit is connected to a TV tuner, you ! You can operate this function only when a need to adjust the TV signal suitable to your Pioneer Vehicle Dynamics Processor (AVG- country TV signal setting. VDP1) is connected to this unit.
The setup function names are displayed and operable ones are highlighted. CAUTION # To return to the previous display, touch BACK. Pioneer recommends the use of a camera # To return to the display of each source, touch which outputs mirror reversed images, other- ESC.
Section Other Functions Touch c to turn rear view camera set- Touch b to select PinP POS. ting on. Touch c or d to select a favorite post- # To turn rear view camera setting off, touch d. ion for the rear view picture. Touch b and then touch c or d to se- Each time you touch c or d it switches be- lect an appropriate setting for polarity.
# To turn the clock display off, touch ON. ! You can operate this function only when a Pioneer Vehicle Dynamics Processor (AVG- Touch c or d to select the segment of VDP1) is connected to this unit.
Section Other Functions Using the AUX source touch b it will display a letter in the reverse order, such as Z Y X ... C B A. An IP-BUS-RCA Interconnector such as the CD-RB20/CD-RB10 (sold separately) lets you connect this unit to auxiliary equipment fea- turing RCA output.
Section Other Functions Note In the following cases, the background display will not change: ! When a list is displayed. ! When the AV (AV input) is not set to VIDEO (refer to page 88). ! When the AVG-VDP1 is not connected to this unit.
Appendix Additional Information Troubleshooting Common Symptom Cause Action (See) Power doesnt turn on. Leads and connectors are incor- Confirm once more that all connections are The unit doesnt operate. rectly connected. correct. The fuse is blown. Rectify the reason for the fuse blowing, then replace the fuse.
Appendix Additional Information Symptom Cause Action (See) The rear view picture (or a black P in P setting is ON. Press ENTERTAINMENT (ENT) button and image when the rear view cam- hold to turn the rear view picture OFF. era is not connected) over the AVG-VDP1 cannot be turned off.
The Video CD playing features PBC. This operation is not possible with Video CDs search are not possible. featuring PBC. Error messages When you contact your dealer or your nearest Pioneer Service Center, be sure to record the error message. Message Cause...
Appendix Additional Information Message Cause Action Error check MIC Microphone is not connected. Plug the supplied microphone securely into the jack. Error check front SP, Error The microphone cannot pick up the ! Confirm that the speakers are connected check FL SP, Error check FR SP, measuring tone of a speaker.
Appendix Additional Information DVD player and care DVD discs ! Use only normal, round discs. If you insert ! With some DVD video discs, it may not be irregular, non-round, shaped discs they possible to use certain functions. may jam in the DVD player or not play prop- ! It may not be possible to play back some erly.
Appendix Additional Information ! Playback of discs recorded on a personal ! This unit allows playback of MP3/WMA computer may not be possible, depending files on CD-ROM, CD-R and CD-RW discs. on the application settings and the environ- Disc recordings compatible with level 1 ment.
Appendix Additional Information About folders and MP3/ ! This unit plays back files with the filename ex- tension (.mp3 or .wma) as an MP3 or a WMA WMA files file. To prevent noise and malfunctions, do not ! An outline of a CD-ROM with MP3/WMA use these extensions for files other than MP3 files on it is shown below.
! Be careful not to place anything between consult your dealer or the nearest authorized the display and the main body when the PIONEER Service Station. Do not use the unit display is opening or closing. If an object in this condition because doing so may result gets between the display and main body, in a fire, electric shock, or other failure.
LCD screen, and cool air from the cool- dealer or the nearest authorized er may cause moisture to form inside the PIONEER Service Station. display resulting in possible damage. Also, if the display is cooled down by the cooler,...
Appendix Additional Information Language code chart for DVD Language (code), input code Language (code), input code Language (code), input code Japanese (ja), 1001 Guarani (gn), 0714 Pashto, Pushto (ps), 1619 English (en), 0514 Gujarati (gu), 0721 Quechua (qu), 1721 French (fr), 0618 Hausa (ha), 0801 Rhaeto-Romance (rm), 1813 Spanish (es), 0519...
Appendix Additional Information Terms formation can include the track title, the ar- tists name, the album title, the music genre, Aspect ratio the year of production, comments and other This is the width-to-height ratio of a TV screen. data. The contents can be freely edited using A regular display has an aspect ratio of 4:3.
Appendix Additional Information Optical digital output/input MP3 is short for MPEG Audio Layer 3. It is an By transmitting and receiving audio signals in audio compression standard set by a working a digital signal format, the chance of sonic group (MPEG) of the ISO (International Stan- quality deteriorating in the course of transmis- dards Organization).
Appendix Additional Information Title DVD video discs have high data capacity, en- abling recording of multiple movies on a sin- gle disc. If, for example, one disc contains three separate movies, they are divided into title 1, title 2 and title 3. This lets you enjoy the convenience of title search and other func- tions.
Appendix Additional Information Specifications Q Factor ....0.35/0.59/0.95/1.15 (+6 dB when boosted) General Gain ......±12dB High Rated power source ....14.4 V DC Frequency ....3.15k/8k/10k/12.5k Hz (allowable voltage range: Q Factor ....0.35/0.59/0.95/1.15 (+6 dB 12.0 14.4 V DC) when boosted) Grounding system ....
Appendix Additional Information Signal-to-noise ratio ....97 dB (1 kHz) (IEC-A net- work) (CD: 96 dB (1 kHz) (IEC-A network)) Dynamic range ......95 dB (1 kHz) (CD: 94 dB (1 kHz)) Distortion ........0.008 % (1 kHz) Output level: Video ........
Index Angle icon ..........32,.81 Subtitle language ........31,.80 Aspect ratio ..........82,.103 Audio language .........30,.81 Title ..............105 TV aspect ............82 Bookmark ............33 Brightness ............22 Video CD ............7 Chapter ............103 Code number ...........82 Wide screen mode ..........21 Color ..............22 Contrast ............22 Direct search ...........30 Dolby Digital ..........9,.103 DTS .............9,.103 Hue ..............22...
TEL: (03) 9586-6300 PIONEER ELECTRONICS OF CANADA, INC. 300 Allstate Parkway, Markham, Ontario L3R OP2, Canada TEL: 1-877-283-5901 PIONEER ELECTRONICS DE MEXICO, S.A. de C.V. Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico, D.F. 11000 TEL: 55-9178-4270 HÒ¡ýÉPlø...