Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Bosch SMI88TS00G
Summary of Contents for Bosch SMI88TS00G
- Page 1 Dishwasher SM... SB... en Instruction manual...
-
Page 3: Table Of Contents
Table of contents e n I n s t r u c t i o n m a n u a l Intended use ....5 Utensils. - Page 4 Operating the appliance ..29 Fault, what to do?... .36 Programme data ....29 Error message .
-
Page 5: Intended Use
Intended use en Before you switch ON the Intended use appliance This appliance is intended Please read the operating and ■ I n t e n d e d u s e for use in the home and the installation instructions home environment. -
Page 6: Installation
en Safety instructions Also follow the installation Installation ■ instructions for the Following installation, ensure dishwasher to ensure that all ■ that the back of the appliances are operated dishwasher is not freely safely. accessible (protection If there is no information or if ■... -
Page 7: In Daily Use
Safety instructions en After installing the appliance, Disposal ■ ensure that the plug is easily Make redundant appliances accessible. ~ "Electrical unusable to prevent connection" on page 50 subsequent accidents. For some models: ■ Dispose of the appliance in The plastic housing on the an environmentally friendly water connection contains an manner. -
Page 8: Door Lock
en Safety instructions When opening and closing Warning ■ the door on an eye-level Risk of explosion! appliance, ensure that Do not add any solvents to the children do not become rinsing compartment. Danger of jammed or crushed between explosion! the appliance door and the cupboard door below. - Page 9 Safety instructions en Activate the child-proof lock Deactivate the child-proof lock (door lock) as follows: (door lock) as follows: Pull the catch of the Press the catch of the child-proof lock towards child-proof lock to the right yourself (1). (1). Close the door (2).
-
Page 10: Environmental Protection
en Environmental protection Environmental Getting to know your protection appliance Both the packaging of new appliances Diagrams of the control panel and the t e c t i o n E n v i r o n m e n t a l p r o y o u r a p p l i a n c e G e t t i n g t o k n o w and the old appliances themselves... -
Page 11: Appliance Interior
Getting to know your appliance en Appliance interior Time setting When the appliance is switched on the See Fig. ~ Page 2 T i m e s e t t i n g for the first time, the time starts at 12:00 1"... -
Page 12: Switching On The Appliance For The First Time
en Getting to know your appliance Switching on the appliance for the first time When the dishwasher is switched on for Change the setting as follows: the first time, you are taken directly to Keep pressing button > )* until the the settings for switching on the required setting is displayed. -
Page 13: Settings
Getting to know your appliance en Settings The dishwasher has been preset with Make the setting with setting buttons certain settings for your convenience. + - X. You can change this factory setting. Press and hold the Info button { 8 for 3 seconds. -
Page 14: Water Softening System
en Water softening system/special salt Setting Factory setting Infotext by pressing Info button { Timelight * While programme is running, status information is projected onto floor. Infolight * Light is projected to signal an active cleaning cycle. Start programme Eco 50° When switching on, the last selected programme appears. -
Page 15: Adjusting The Water Softening System
Water softening system/special salt en Adjusting the water softening Top up the salt as follows: Undo the screw plug on the system dispenser 1R. Fill the dispenser with water The amount of salt dispensed can be (required only when switching on the set from 0 to 62°E. -
Page 16: System
en Rinse aid Switching off low salt Top up the rinse-aid as follows: Open dispenser 9"; press lug on indicator / water softening the lid (1) and lift (2). system If the use of combined detergents with a s t e m t e r s o f t e n i n g s y S w i t c h i n g o f f w a salt component impairs the low salt... -
Page 17: Setting Amount Of Rinse Aid
Utensils en Setting amount of rinse aid Utensils The amount of rinse aid to be Not suitable dispensed can be set from 0 to 6. Set U t e n s i l s the amount of rinse aid to be dispensed Cutlery and utensils made of wood. -
Page 18: Loading The Dishwasher
en Utensils Loading the dishwasher Utensils must not be placed Note: above the tablet collecting tray 1B. These may block the lid of the detergent Remove large food remnants. It dispenser and prevent it from opening is not necessary to prerinse utensils fully. -
Page 19: Cutlery Basket
Utensils en Other examples, such as the best Depending on the features of your Tip: way of loading your dishwasher, can be dishwasher, you can fold down the side found on our homepage. These can be shelves to provide more room for taller downloaded free of charge. -
Page 20: Etagere
en Utensils Etagere * Folding spikes * The etagere and the space underneath * Depending on the features of your E t a g e r e F o l d i n g s p i k e s can be used for small cups and glasses dishwasher, the spikes can be folded or for larger items of cutlery, such as... -
Page 21: Knife Rack
Utensils en Knife rack * Baking sheet spray head * * Depending on the features of your * depending on the features of your K n i f e r a c k y h e a d B a k i n g s h e e t s p r a dishwasher, the upper basket is fitted dishwasher with a knife shelf. -
Page 22: Unloading The Dishwasher
en Utensils Unloading the dishwasher Adjusting the height of the basket * To prevent water from dripping off the * depending on the features of your upper basket onto the utensils in the i g h t o f t h e b a s k A d j u s t i n g t h e h e dishwasher lower basket, it is recommended... - Page 23 Utensils en Arrange large plates up to a diameter of To lift the upper basket; grip the 31/34* cm in the lower basket 1j as sides of the upper basket along the illustrated. upper edge and lift. Ensure that both sides of the upper basket are at the same height.
-
Page 24: Detergent
en Detergent Adding detergent Detergent If the detergent dispenser 9* is still You can use tablets as well as powder closed, actuate locking bar 92 to D e t e r g e n t or liquid detergents for dishwashers, but open it. -
Page 25: Combination Detergent
Detergent en If the utensils are only lightly If programmes are short, tablets may Tip: ■ soiled, slightly less than the indicated not have full cleaning effect due to amount of detergent is usually different dissolving properties and adequate. there may even be undissolved Suitable detergents and care products detergent residue. -
Page 26: Overview Of Programmes
en Overview of programmes Overview of programmes The max. possible number of programmes is illustrated in this overview. The a m m e s O v e r v i e w o f p r o g r corresponding programmes and their arrangement can be found on the fascia. Type of utensils Type of soiling programme Possible... -
Page 27: Programme Selection
Overview of programmes en Type of utensils Type of soiling programme Possible Programme sequence additional options intensiveZone option Pre Rinse part dried, common Half load option Clean 50° Û mixed utensils household food HygienePlus Intermediate rinse and cutlery Night remnants extraDry Option Final rinse 63°... -
Page 28: Additional Functions
en Additional functions Ï intensiveZone * Additional functions Perfect for a mixed load. You can wash i n t e n s i v e Z o n e very soiled pots and pans in the lower * Depending on the features of your i o n s A d d i t i o n a l f u n c t basket together with normally soiled... -
Page 29: Operating The Appliance
Operating the appliance en AquaSensor * Operating the * depending on the features of your appliance A q u a S e n s o r dishwasher The Aqua sensor is an optical Programme data measuring device (light barrier) which p l i a n c e O p e r a t i n g t h e a p measures the turbidity of the rinsing... -
Page 30: Sensor Setting
en Operating the appliance Sensor setting AutoPowerOff (Switching off automatically after the end of The programme sequence is optmised the programme) in Auto programmes with the aid of sensors. The sensors adjust the To save energy, the dishwasher A u t o P o w e r O f f programme strength of Auto is switched off 1 minute after programmes depending on the amount... -
Page 31: Timelight
Operating the appliance en TimeLight (Optical display Button volume while the programme is When you are operating the dishwasher, running) * a signal sounds whenever a button is pressed. You can control the volume of * depending on the features of your t i m e L i g h t the signal. -
Page 32: Factory Setting
en Operating the appliance Factory setting Open the door. Switch on ON/OFF switch (. You can reset all settings to the factory Selects programme 0. setting. Press time preselection button `. Keep pressing the setting buttons + - X until the displayed time Switching the appliance on corresponds with your requirements. -
Page 33: Interrupting The Programme
Operating the appliance en Terminating the programme About the Eco drying function: When Eco drying is activated in the (Reset) Eco 50° programme, the door opens Open the door. automatically when the programme p r o g r a m m e T e r m i n a t i n g t h e Press the START button )"... -
Page 34: Cleaning And Maintenance
en Cleaning and maintenance Never use a steam cleaner to clean Cleaning and your dishwasher. The manufacturer is not liable for any consequential maintenance damage. Regularly wipe the front A regular inspection and maintenance t e n a n c e C l e a n i n g a n d m a i n of the appliance and fascia with a damp of your machine will help to prevent... -
Page 35: Filters
Cleaning and maintenance en Filters Spray arms The filters 1Z keep large foreign Limescale and contaminants in the objects in the rinsing water away from rinsing water may block nozzles and the pump. hese foreign objects may bearings on the spray arms 1: and occasionally block the filters. -
Page 36: Fault, What To Do
en Fault, what to do? Error message Fault, what to do? Some faults are indicated at the top of the display window @ and on the front Experience has shown that you can F a u l t , w h a t t o d rectify most faults which occur in daily display * ): and possible remedies are offered (for example Filter system... -
Page 37: Waste Water Pump
Fault, what to do? en Waste water pump Check impeller wheel and remove any foreign objects. Large food remnants or foreign objects Place pump cover in the original which were not captured by the filters position (2) and press down until it may block the waste water pump. -
Page 38: Fault Table
en Fault, what to do? Fault table Fault Cause Remedial action Error code “:‚‰ is lit. Supply hose kinked. Install supply hose without kinks. Tap turned off. Turn on the tap. Tap jammed or calcified. Turn on the tap. Flow rate must be min. 10 l/min. when water supply is open. - Page 39 Fault, what to do? en Fault Cause Remedial action Error code “:ƒˆ is lit. Mains voltage too low. Not an appliance fault, have the mains voltage and electrical installation checked. A different error code is A technical fault has probably Switch off the appliance with the ON/OFF indicated on the digital occurred.
- Page 40 en Fault, what to do? Fault Cause Remedial action Utensils not dry. No or too little rinse aid in the Refill rinse aid. dispenser. Programme selected without Select programme with drying. drying. ~ "Overview of programmes" on page 26 Water collecting in depressions Arrange utensils in a sloping position, on the utensils and cutlery.
- Page 41 Fault, what to do? en Fault Cause Remedial action Food remnants on the Utensils placed too closely Arrange utensils with adequate clearance utensils. together, utensils basket between them ensuring that the spray jets overfilled. can reach the surface of the utensils. Prevent contact points.
- Page 42 en Fault, what to do? Fault Cause Remedial action Detergent residue. Detergent dispenser cover 9* Utensils must not be placed above the blocked by utensils and therefore tablet collecting tray 1B. These may does not open fully. block the lid of the detergent dispenser and prevent it from opening fully.
- Page 43 Fault, what to do? en Fault Cause Remedial action White, stubborn coatings; Detergent substances are Change detergent brand. limescale on the utensils, deposited. These coatings cannot Clean appliance mechanically. container or door. usually be removed with chemicals (appliance cleaner, ...). Hardness range incorrectly set or Set water softening system according to water hardness greater than 8.9...
- Page 44 en Fault, what to do? Fault Cause Remedial action Plastic parts discoloured. Too low rinsing temperature. Select programme with higher washing temperature. Utensils precleaned too intensely; Do not prerinse utensils. Remove only sensors therefore decide on large food remnants. weak programme sequence. Increase sensitivity of the sensors.
- Page 45 Fault, what to do? en Fault Cause Remedial action Appliance cannot be Malfunction. Disconnect appliance from the power switched on or operated. supply; pull out the mains plug or switch off the fuse. Wait at least 5 seconds, then connect the appliance to the power supply.
- Page 46 en Fault, what to do? Fault Cause Remedial action Cover on the detergent Detergent dispenser or cover Remove detergent residue. dispenser cannot be guide blocked by sticky detergent closed. residue. Detergent residue in the Spray arms blocked by utensils, Ensure that the spray arms can rotate detergent dispenser 9* therefore detergent is not rinsed freely.
-
Page 47: Customer Service
Customer service en Customer service Installation and connection If you are unable to rectify the fault, C u s t o m e r s e r v i c e please contact your customer service. The dishwasher must be connected We will always find an appropriate c o n n e c t i o n I n s t a l l a t i o n a n d... -
Page 48: Delivery
en Installation and connection Delivery Installation Your dishwasher has been checked The required installation dimensions thoroughly in the factory to ensure that can be found in the installation it is in working order. This may cause instructions. Level the appliance with small water stains. -
Page 49: Drinking Water Connection
Installation and connection en Drinking water connection To change the setting: Open the door. Switch on ON/OFF switch (. Fasten the drinking water connection Press Info button {8 for 3 to the tap according seconds until the following text is to the installation instructions using indicated on the display window at the enclosed parts. -
Page 50: Electrical Connection
en Installation and connection Electrical connection Removal Connect the appliance to an Also observe ■ alternating current only, ranging from the sequence of worksteps here. 220 V to 240 V and 50 Hz or 60 Hz Disconnect the appliance from the via a correctly installed socket with power supply. -
Page 51: Transporting
Installation and connection en Transporting Protection against frost If the appliance is in a room where there Empty the dishwasher and secure loose n g t h e a p p l i a n c e ) s t f r o s t ( E m p t y i P r o t e c t i o n a g a i n is a risk of frost (e.g. - Page 52 *9000989750* 9000989750 (9506) 642 TW...