Safety instructions Delivery The electrical connection conditions must correspond 1. Check the packaging and with the specifications dishwasher immediately for on the dishwasher rating plate 9*. damage caused in transit. Do not switch on a damaged If the power cord of this appliance, but contact your appliance is damaged, supplier.
Safety instructions If you cannot obtain any In daily use information from Read and observe the safety the manufacturer, you must information and instructions not install the dishwasher for use on the packaging above or below these for cleaning and rinsing agents. appliances.
Safety instructions Deactivating the button lock: Warning Risk of injury! Hold down the button + for To prevent injuries, e.g. approx. 4 sec. until the caused by stumbling, open display goes out. the dishwasher only briefly When the programme ends in order to load and unload on the digital display), the the dishwasher.
Safety instructions When opening and closing Warning the door on an eye-level Risk of scalding! appliance, ensure that Open the door carefully when children do not become the programme is still running. jammed or crushed between There is a risk of hot water the appliance door and the spraying out of the appliance.
Rinse aid Overview of menu 2. Carefully pour rinse aid up to the max. mark in the filler opening. The settings can be found in the individual chapters. Intensive drying : Rinse aid : Automatic disconnection : Rinse aid R i n s e a i d 3.
Utensils To change the setting: Glass and utensil damage 1. Press programme button 3. Causes: Each time the button is pressed, the set value increases by one level; Glass type and glass production when the value of : has been process.
Utensils Unloading the dishwasher Pans Bottom basket 1Z To prevent water from dripping off the upper basket onto the utensils in the lower basket, it is recommended to empty the appliance from the bottom Hot utensils are sensitive to shock! Therefore, when the programme ends, leave the utensils to cool down in the dishwasher until they can be handled.
Utensils Cutlery basket Small accessories holder * S m a l l a c c e s s o r i e s h o l d e r You should always place cutlery * depending on model unsorted with the points downwards. Light-weight plastic accessories, e.g.
Detergent Adding detergent Detergent 1. If the detergent dispenser 1j is still D e t e r g e closed, press the lock 9" to open You can use tablets as well as powder the detergent dispenser. or liquid detergents for dishwashers, but never use washing up liquid.
Detergent Notes If the utensils are only lightly soiled, If programmes are short, tablets slightly less than the indicated amount may not have full cleaning effect of detergent is usually adequate. due to different dissolving properties and there may even be undissolved Suitable detergents and care products detergent residue.
Overview of programmes Overview of programmes p r o g r a m m e s O v e r v i e w o f The max. possible number of programmes is illustrated in this overview. The corresponding programmes for your appliance can be found on the fascia. The programme data has been measured in the laboratory according to AS/NSZ 2007.
Additional options Ï Intensive zone * Additional options I n t e n s i v e z o n e o n a l A d d i t i o p t i o n s Perfect for a mixed load. You can wash * depending on model very soiled pots and pans in the lower basket together with normally soiled...
Operating the appliance Remaining running time Operating display the appliance When the programme is selected, the O p e r a t i i a n c e t h e a p p l remaining running time of the A qua sensor * programme is indicated on the digital A q u a s e n s o r...
Operating the appliance End of programme Switching off the appliance The programme has ended when the Short time after the end of the value : is indicated on the numerical programme: display h. 1. Switch off ON/OFF switch (. 2. Turn off the tap (not applicable if Aqua-Stop fitted).
Cleaning and maintenance Warning – Health hazard 3. Remove any residue and clean filters under running water. Never use other domestic detergents, e.g. containing chlorine! 4. Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after Rinse aid closing the filter system.
Fault, what to do? Spray arms Fault, what to do? F a u l t , w h a t d o ? Limescale and contaminants in the rinsing water Experience has shown that you can may block nozzles rectify most faults which occur in daily and bearings on the spray arms 1: operation yourself.
Fault, what to do? Waste water pump Large food remnants or foreign objects which were not captured by the filters may block the waste water pump. The rinsing water will then be above the filter. Warning – Risk of cuts! When cleaning the waste water pump, ensure that you do not injure yourself on pieces of broken glass or pointed...
Fault, what to do? Fault table Fault Cause Remedial action “Check water supply” Supply hose kinked. Install supply hose without kinks. display X lights up. Tap turned off. Turn on the tap. Tap jammed or calcified. Turn on the tap. Flow rate must be min.
Fault, what to do? Fault Cause Remedial action A different error code is A technical fault has probably Switch off appliances with the ON/OFF switch (. After a short time restart indicated on the digital occurred. display. the appliance. to : If the problem recurs, turn off the tap and pull out the mains plug.
Fault, what to do? Fault Cause Remedial action Utensils not dry. No or too little rinse aid Refill rinse aid. in the dispenser. Programme selected without Select programme with drying (see drying. Overview of programmes, Programme sequence). Water collecting in depressions Arrange utensils in a sloping position, on the utensils and cutlery.
Fault, what to do? Fault Cause Remedial action Food remnants Utensils placed too closely Arrange utensils with adequate clearance on the utensils. together, utensils basket between them ensuring that the spray jets overfilled. can reach the surface of the utensils. Prevent contact points.
Fault, what to do? Fault Cause Remedial action Washable or water-soluble Detergent substances are Change detergent brand. coatings in the container or deposited. These coatings cannot Clean appliance mechanically. on the door. usually be removed with chemicals (appliance cleaner, ...). Only for glasses: Initial glass See Glass and utensil damage.
Fault, what to do? Fault Cause Remedial action Removable streaks on Too much rinse aid. Set rinse aid amount to lower setting. glasses, glasses with No rinse aid added or setting too Add rinse aid and check dosage metallic appearance and low.
Fault, what to do? Fault Cause Remedial action Cover on the detergent Detergent dispenser or cover Remove detergent residue. dispenser cannot be guide blocked by sticky detergent closed. residue. Detergent residue Spray arms blocked by utensils, Ensure that the spray arms can rotate freely. in the detergent dispenser therefore detergent is not rinsed or in the tablet collecting...
Customer service Customer service Installation and connection C u s t o m e r s e r v i c e If you are unable to rectify the fault, l a t i o n I n s t a l a n d c o n n e c t i please contact your customer service.
Installation and connection Delivery Installation Your dishwasher has been checked The required installation dimensions can thoroughly in the factory to ensure that it be found in the installation instructions. is in working order. This may cause Level the appliance with the aid of the small water stains.
Installation and connection Drinking water connection Electrical connection 1. Fasten the drinking water connection Connect the appliance to an to the tap according alternating current only, ranging from to the installation instructions using 220 V to 240 V and 50 Hz or 60 Hz the enclosed parts.
Installation and connection Removing the appliance Protection against frost P r o t e c t i o n a g a i n s t f r o s t ( E m p t y i n g t h e a p p l i a n c e ) Also observe If the appliance is in a room where there the sequence of worksteps here.
*9000955004* 9000955004 aus (9401) 440MA...