Bosch SM Series Instruction Manual
Hide thumbs
Also See for SM Series:
- Instructions for use manual (68 pages) ,
- Instructions manual (64 pages) ,
- User manual (60 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Bosch SM Series
Summary of Contents for Bosch SM Series
- Page 1 Dishwasher SM... SB... en Instruction manual...
- Page 2 (08@HPX`h)")*)2):)B)J)R 1"1*121:1B1J1R1Z1b1j9"9*929:9B9J...
-
Page 3: Table Of Contents
Table of contents e n I n s t r u c t i o n m a n u a l Intended use ....5 Water softening system / special salt . - Page 4 Additional functions ..31 Cleaning and maintenance ..37 Save time (VarioSpeedPlus) ..31 Overall condition of the machine . . . 37 Half load ..... .31 Special salt and rinse aid .
-
Page 5: Intended Use
Intended use en from the appliance and power Intended use cable. This appliance is intended ■ Before you switch ON the I n t e n d e d u s e for use in the home and appliance domestic environments. Use the dishwasher only in Please read the instructions for ■... -
Page 6: Installation
en Safety instructions Also follow the installation Installation ■ instructions for the Following installation, ensure dishwasher to ensure that all ■ that the back of the appliances are operated dishwasher is not freely safely. accessible (protection If there is no information or if ■... -
Page 7: In Daily Use
Safety instructions en Please note that the Damage ■ insulation material of the The appliance may be dishwasher power cord may ■ repaired and opened up by a melt next to heat sources technician only. To do this, (e.g. heating / hot water disconnect the appliance installations) or hot from the power supply. - Page 8 en Safety instructions Do not lean or sit on the Keep children away from ■ ■ open door. detergents and rinse aid. In the case of free-standing These may cause chemical ■ appliances, ensure that the burns in the mouth, throat baskets are not overloaded.
-
Page 9: Door Lock
Safety instructions en Childproof lock (door lock) * The child-proof lock (door lock) D o o r l o c k protects children from potential hazards which the dishwasher poses. Warning Risk of suffocation! Children may become locked in the dishwasher and suffocate. Always completely close the Deactivate the child-proof lock appliance door when leaving... -
Page 10: Environmental Protection
en Environmental protection Environmental Getting to know your protection appliance Both the packaging of new appliances Diagrams of the control panel and the t e c t i o n E n v i r o n m e n t a l p r o y o u r a p p l i a n c e G e t t i n g t o k n o w and the old appliances themselves... -
Page 11: Appliance Interior
Getting to know your appliance en Appliance interior Time setting When the appliance is switched on the 1" Interior light * T i m e s e t t i n g for the first time, the time starts at 12:00 1* Cutlery drawer * o’clock. -
Page 12: Initial Start-Up
en Getting to know your appliance Initial start-up When the dishwasher is switched on for Scroll with < > the first time, you are taken directly to Set with - + the settings for the initial start-up. Leave with Setup 3 sec. The required settings for the initial If you select Home Connect Note:... -
Page 13: Settings
Getting to know your appliance en Settings The dishwasher has been preset with Keep pressing button >)R until the certain settings for your convenience. required setting is displayed. However you can also change this Make the setting with setting buttons factory setting. - Page 14 en Getting to know your appliance Basic setting Factory setting Infotext by pressing Info button { timeLight * While programme is running, status information is projected on floor. infoLight * Light is projected to signal an active cleaning cycle. Start up programme Magic Daily When switching on, the last selected programme appears.
-
Page 15: Home Connect
Home Connect en Setting up Home Connect Home Connect You can set your dishwasher by pressing the remote start button }h This dishwasher ist Wi-Fi capable and H o m e C o n n e c t can be remotely controlled via a mobile or proceed as follows: terminal device. -
Page 16: Network Login
en Home Connect Network login Connect to App The “Network login” menu option is not The “Connect to App” menu option is available unless you have activated not available unless there was a Wi-Fi. connection to the home network. In the “Network login” menu you can The “Connect to App”... -
Page 17: Remote Start Button
Declaration of Conformity aborted during start-up, press the remote start button }h again. Robert Bosch Hausgeräte GmbH o n f o r m i t y D e c l a r a t i o n o f C... -
Page 18: Water Softening System
en Water softening system/special salt Adjusting the water softening Water softening system system / special salt The amount of salt dispensed can be set from 0 to 62°E. Salt is not required To ensure good rinsing results, the at the set value 0-8. s y s t e m / s p e c i a l s a W a t e r s o f t e n i n g dishwasher requires soft water, i.e. -
Page 19: Using Special Salt
Water softening system/special salt en Using special salt Using detergents with salt component As soon as the low salt indicator P is If combined detergents with a salt lit on the control panel or is requested s a l t c o m p o n e n t D e t e r g e n t w i t h a component are used, special salt can on the front display * )2, salt should... -
Page 20: Rinse Aid
en Rinse aid Close the lid. Rinse aid Lid “clicks” into position. Remove overflowed rinse aid with a As soon as the low rinse-aid indicator cloth. R i n s e a i d H is lit on the control panel or is This prevents excessive frothing requested on the front display * )2, during the next rinse cycle. -
Page 21: Switching Off Rinse Aid Refill Indicator
Utensils en Switching off rinse aid refill Utensils indicator Not suitable If the use of combined detergents with a U t e n s i l s rinse-aid component impairs the low Cutlery and utensils made of wood. rinse-aid indicator H on the control ■... -
Page 22: Loading The Dishwasher
en Utensils Loading the dishwasher Remove large food remnants. It is not necessary to prerinse utensils under running water. Place the utensils so that they are secure and cannot tip – over. all utensils with their openings – face down. parts with curves or indentations –... -
Page 23: Cutlery Basket
Utensils en Cutlery basket * Place cutlery, always unsorted with the C u t l e r y b a s k e t tips face down, in the cutlery basket *. To prevent injuries, place long, pointed implements and knives on the knife shelf *. -
Page 24: Etagere
en Utensils Folding spikes * The chopstick basket can be removed to improve arrangement of pans, bowls * Depending on the features of your and glasses. F o l d i n g s p i k e s dishwasher, the spikes can be folded down. -
Page 25: Knife Rack
Utensils en Knife rack * Baking sheet spray head * * Depending on the features of your * depending on the features of your K n i f e r a c k y h e a d B a k i n g s h e e t s p r a dishwasher, the upper basket is fitted dishwasher with a knife shelf. -
Page 26: Unloading The Dishwasher
en Utensils Unloading the dishwasher Appliance height 81.5 cm With cutlery basket Upper Lower To prevent water from dripping off the basket basket upper basket onto the utensils in the Setting 1 max. ø 22 cm 31 cm lower basket, it is recommended to empty the appliance from the bottom Setting 2 max. - Page 27 Utensils en Upper basket with side levers Pull out upper basket 12. Hold the sides of the basket along the upper edge. This prevents it from suddenly dropping. To lower the upper basket; press in both levers on the left and right on the outside of the basket.
-
Page 28: Detergent
en Detergent Adding detergent Detergent If the detergent dispenser 9: is still You can use tablets as well as powder closed, actuate locking bar 9B to D e t e r g e n t or liquid detergents for dishwashers, but open it. -
Page 29: Combination Detergent
Detergent en If the utensils are only lightly If programmes are short, tablets may Tip: ■ soiled, slightly less than the indicated not have full cleaning effect due to amount of detergent is usually different dissolving properties and adequate. there may even be undissolved Suitable detergents and care products detergent residue. -
Page 30: Overview Of Programmes
en Overview of programmes Overview of programmes The max. possible number of programmes is illustrated in this overview. The a m m e s O v e r v i e w o f p r o g r corresponding programmes and their arrangement can be found on the fascia. Type of utensils Type of soiling Programme Possible... -
Page 31: Programme Selection
Additional functions en -------- Programme selection Additional functions You can select a suitable programme according to the type of utensils and * Depending on the features of your i o n s A d d i t i o n a l f u n c t type of soiling. -
Page 32: Intensivezone
en Operating the appliance Ï intensiveZone * Operating the Perfect for a mixed load. You can wash appliance i n t e n s i v e Z o n e very soiled pots and pans in the lower basket together with normally soiled Programme data utensils in the upper basket. -
Page 33: Aquasensor
Operating the appliance en AquaSensor * ¼ Zeolith drying * depending on the features of your Warning A q u a S e n s o r dishwasher Z e o l i t h d r y i n g Risk of burns from touching the blow The Aqua sensor is an optical opening 1R! -
Page 34: Sensor Setting
en Operating the appliance Sensor setting AutoPowerOff (Switching off automatically after the end of The programme sequence is optmised the programme) in Auto programmes with the aid of sensors. The sensors adjust the To save energy, the dishwasher A u t o P o w e r O f f programme strength of Auto is switched off 1 minute after programmes depending on the amount... -
Page 35: Timelight
Operating the appliance en TimeLight (Optical display Button volume while the programme is When you are operating the dishwasher, running) * a signal sounds whenever a button is pressed. You can control the volume of * depending on the features of your t i m e L i g h t the signal. -
Page 36: Switching On The Appliance
en Operating the appliance Switching on the appliance Programme end * The programme has ended when Turn on the tap fully. “Finished” is indicated on the display Open the door. window at the top @ and on the front Switch on ON/OFF switch (. display * )2. -
Page 37: Interrupting The Programme
Cleaning and maintenance en Interrupting the programme Cleaning and maintenance Caution! Expansion (overpressure) may cause the appliance door to jump open and/or A regular inspection and maintenance water to escape! If the door was opened t e n a n c e C l e a n i n g a n d m a i n of your machine will help to prevent on an appliance which has a hot water... -
Page 38: Special Salt And Rinse Aid
en Cleaning and maintenance Filters Never use a steam cleaner to clean your dishwasher. The manufacturer The filters 1j keep large foreign is not liable for any consequential objects in the rinsing water away from damage. the pump. hese foreign objects may Regularly wipe the front occasionally block the filters. -
Page 39: Spray Arms
Fault, what to do? en Spray arms Fault, what to do? Limescale and contaminants in the rinsing water may block nozzles and Experience has shown that you can F a u l t , w h a t t o d bearings on the spray arms 1: and rectify most faults which occur in daily operation yourself. -
Page 40: Waste Water Pump
en Fault, what to do? Waste water pump Check impeller wheel and remove any foreign objects. Large food remnants or foreign objects Place pump cover in the original which were not captured by the filters position (2) and press down until it may block the waste water pump. -
Page 41: Fault Table
Fault, what to do? en Fault table Fault Cause Remedial action Error code “:‚‰ is lit. Supply hose kinked. Install supply hose without kinks. Tap turned off. Turn on the tap. Tap jammed or calcified. Turn on the tap. Flow rate must be min. 10 l/min. when water supply is open. - Page 42 en Fault, what to do? Fault Cause Remedial action Error code “:ƒ† is lit. Waste water pump blocked or Clean pump and lock cover correctly. cover on the waste water pump is ~ "Waste water pump" on page 40 not locked in position. Error code “:ƒˆ...
- Page 43 Fault, what to do? en Fault Cause Remedial action Utensils not dry. No or too little rinse aid in the Refill rinse aid. dispenser. Programme selected without Select programme with drying. drying. ~ "Overview of programmes" on page 30 Water collecting in depressions Arrange utensils in a sloping position, on the utensils and cutlery.
- Page 44 en Fault, what to do? Fault Cause Remedial action Food remnants on the Utensils placed too closely Arrange utensils with adequate clearance utensils. together, utensils basket between them ensuring that the spray jets overfilled. can reach the surface of the utensils. Prevent contact points.
- Page 45 Fault, what to do? en Fault Cause Remedial action Detergent residue. Detergent dispenser cover 9: Utensils must not be placed above the blocked by utensils and therefore tablet collecting tray 1B. These may does not open fully. block the lid of the detergent dispenser and prevent it from opening fully.
- Page 46 en Fault, what to do? Fault Cause Remedial action White, stubborn coatings; Detergent substances are Change detergent brand. limescale on the utensils, deposited. These coatings cannot Clean appliance mechanically. container or door. usually be removed with chemicals (appliance cleaner, ...). Hardness range incorrectly set or Set water softening system according to water hardness greater than 8.9...
- Page 47 Fault, what to do? en Fault Cause Remedial action Plastic parts discoloured. Too low rinsing temperature. Select programme with higher washing temperature. Utensils precleaned too intensely; Do not prerinse utensils. Remove only sensors therefore decide on large food remnants. weak programme sequence. Increase sensitivity of the sensors.
- Page 48 en Fault, what to do? Fault Cause Remedial action Appliance cannot be Malfunction. Disconnect appliance from the power switched on or operated. supply; pull out the mains plug or switch off the fuse. Wait at least 5 seconds, then connect the appliance to the power supply.
- Page 49 Fault, what to do? en Fault Cause Remedial action Knocking or rattling noise. Spray arm strikes the utensils, Position utensils so that the spray arms do utensils not positioned correctly. not strike the utensils. If there is a low load, the water Load the appliance with more utensils or jets strike the washing tank distribute the utensils more evenly in the...
-
Page 50: Customer Service
en Customer service Customer service Installation and connection If you are unable to rectify the fault, C u s t o m e r s e r v i c e please contact your customer service. The dishwasher must be connected We will always find an appropriate c o n n e c t i o n I n s t a l l a t i o n a n d... -
Page 51: Delivery
Installation and connection en Delivery Installation Your dishwasher has been checked The required installation dimensions thoroughly in the factory to ensure that can be found in the installation it is in working order. This may cause instructions. Level the appliance with small water stains. -
Page 52: Drinking Water Connection
en Installation and connection Drinking water connection To change the setting: Open the door. Switch on ON/OFF switch (. Fasten the drinking water connection Press Info button {8 for 3 to the tap according seconds until the following text is to the installation instructions using indicated on the display window at the enclosed parts. -
Page 53: Removal
Installation and connection en Use only a residual current operated Close the door. ■ circuit-breaker which features the Open the door after approx. 1 symbol ‚. Only this extension minute. guarantees compliance with The display window at the top @ the currently valid regulations. - Page 56 *9001154100* 9001154100 (9502) 642 TW...