Hints For Timer Recording - Sanyo FWZV475F Owner's Manual

Hints for Timer Recording

If there is a power failure or this unit has been
•
unplugged for more than 30 seconds, the clock setting
and all timer programming will be lost.
If a disc is not inserted, "DVD" on the front panel display
•
flashes and timer recording cannot be performed. In
some cases, will appear momentarily around the
start time as the unit attempts to record. Please insert a
recordable disc.
If a cassette tape with a erase-protection tab is not
•
in the cassette compartment or there is no cassette
tape in the cassette compartment, "VCR" on the front
panel display flashes and timer recording cannot be
performed. Please insert a recordable cassette tape.
If a cassette tape ends during the timer recording, the
•
unit will automatically stop, eject the cassette tape, and
turn itself to the standby mode. To continue recording,
insert a recordable tape.
When all the timer recordings are completed,
•
flashes. Press [TIMER SET] to release the unit from the
timer standby mode.
If both DVD and VCR are timer programmed, you cannot
•
use any functions for either unit during timer standby or
timer recording. If you want to use functions other than
recording under such condition, cancel timer recording
by pressing [TIMER SET] during timer standby or stop
recording by pressing [C ] / [C A] on the front panel of
the unit during timer recording.
To cancel the timer standby mode, press [TIMER SET].
•
The Priority of Overlapped Settings
Timer program which has the earlier start time will be placed first in the timer program list, and be given priority over
•
the programs with the later start time when timer programs overlap.
When timer programs overlap, the first 2 minutes (at the longest) of the later recording will be cut off.
•
When 2 or more timer programs have the same start time, the program set first will be given priority.
•
A timer recording of lower priority will be cancelled or start from the middle.
•
Check the overlapped timer programmings and change the priority if necessary.
•
When the starting time is the same:
A program set previously (PROG. A) has priority.
PROG. A
PROG. B
actual
PROG. A
recording
The first 2 minutes (at the longest) will be cut off
(when recording to DVD only).
Note for DVD recording
When the recording time is partially overlapped:
PROG. A will start after PROG. B is complete to
When the recording time of 2 programs are overlapped or
•
be recorded.
the end time of a program and the start time of another
program is the same, the first 2 minutes (at the longest) of
PROG. A
the subsequent program will be cut off.
PROG. B
If the cut-off portion comes up to 3 minute or more, this
•
program will be displayed with error number E40 in the timer
actual
programming list.
PROG.B
recording
The first 2 minutes (at the longest) will be cut off.
34 34 EN EN
TIMER RECORDING
When the starting and the ending time are the same,
•
"Exceeds 12 hours" appears and the program setting
will not be accepted.
When the disc or cassette tape becomes full during the
•
recording, the unit turns itself to the standby mode.
If the starting time is earlier and the ending time is later
•
than the current time, the recording will start right after
you press [TIMER SET] at step 9 on page 32.
The timer recording cannot be performed in DVD and
•
VCR at the same time. If you set 2 programmings with
the same channel and time in both devices, the program
which is set first will have the priority.
"Press TIMER SET for timer recording" will appear
•
on the TV screen 5 minutes before the programmed
starting time.
When the starting time and the ending time
for each programs are different:
A program that has earlier start time (PROG.C)
has priority.
PROG. A
PROG. B
PROG. C
PROG. B
actual
recording
The first 2 minutes (at the longest) will be cut off.
When the recording time is entirely overlapped:
PROG.A will not be recorded.
PROG. A
PROG. B
actual
recording
PROG. A
PROG.A
PROG. B
actual
recording
The first 2 minutes (at the longest) will be cut off.
PROG. A
When the end time of the programming
currently being recorded and the start time
of the subsequent program are same:
The beginning of the PROG. B may be cut off.
PROG. B
PROG. A
PROG. C PROG. B
PROG. B