Table of Contents
Advertisement
Quick Links
Owner's Manual
10 in. Stationary
TABLE SAW
Model No.
315.228510
Save this manual for
future reference.
CAUTION:
Read and follow all
Safety Rules and Operating
Instructions before first use of this
product.
Customer Help Line: 1-800-932-3188
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
Visit the Craftsman web page: www.sears.com/craftsman
972000-526
7-99
1
• Safety
• Features
• Assembly
• Operation
• Maintenance
• Parts List
NRTL/C
®
TABLE SAW 315.228510
Advertisement
Table of Contents
Related Manuals for Craftsman 315.228510
Summary of Contents for Craftsman 315.228510
- Page 1 Instructions before first use of this • Operation product. • Maintenance Customer Help Line: 1-800-932-3188 • Parts List Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA Visit the Craftsman web page: www.sears.com/craftsman NRTL/C 972000-526 7-99 ® TABLE SAW 315.228510...
-
Page 2: Table Of Contents
WARRANTY FULL ONE YEAR WARRANTY ON CRAFTSMAN TABLE SAW If this Table Saw fails due to a defect in material or workmanship within one year from the date of purchase, Sears will repair it, free of charge. Contact a Sears Service Center for repair. -
Page 3: Table Of Contents
Making a Large Panel Cut ..........................45 Making a Dado Cut ............................46 Making a Non-Through Cut .......................... 46 Maintenance ..............................47 Lubrication ..............................47 Troubleshooting ............................48-50 Exploded View and Repair Parts List ...................... 54-71 Parts Ordering / Service ........................back page ® TABLE SAW 315.228510... -
Page 4: Rules For Safe Operation
DO NOT leave tools or pieces of wood on the tentionally contacted. saw while it is in operation. ® TABLE SAW 315.228510... - Page 5 A wire gage size When servicing, use only identical (A.W.G.) of at least 14 is recommended for an Craftsman replacement parts. Use of any other extension cord 25 feet or less in length. If in parts may create a hazard or cause product doubt, use the next heavier gage.
-
Page 6: Save These Instructions
If you the blade guard. NEVER TOUCH BLADE or loan someone this tool, loan them these instruc- other moving parts during use, for any reason. tions also. WARNING: Blade coasts after being turned off. SAVE THESE INSTRUCTIONS ® TABLE SAW 315.228510... -
Page 7: Electrical
Figure 1. It also has a grounding pin like the one shown. ELECTRICAL CONNECTION Your Sears Craftsman Table Saw is powered by a WARNING: Instructions are given in the precision built electric motor. It should be connected... -
Page 8: Glossary And Product Specifications
Cutting Capacity with Miter at 0˚/Bevel 0˚: 3-3/8 in. Table Size without table extensions 20 in. x 27 in. Table Size with table extensions 44 in. x 27 in. Cutting Capacity with Miter at 0˚/Bevel 45˚: 2-1/4 in. ® TABLE SAW 315.228510... -
Page 9: Unpacking And Accessories
2 Bit Molding Head Set • 8 in. Sanding Disc • Saw Baskets • Elite Dado • Jointer Clamps • Excalibur Dado • Specialty Throat Plate WARNING: The use of attachments or accessories not listed might be hazardous. ® TABLE SAW 315.228510... -
Page 10: Loose Parts List
N. Switch Key ............1 F. Handwheel O. Rip Fence ............. 1 (Hardware Shown Separately) ......2 P. Rail, Front (Hardware Shown Separately) .... 1 G. Leg Brace, lower (short) ........2 Q. Rail, Rear (Hardware Shown Separately) .... 1 ® TABLE SAW 315.228510... -
Page 11: Small Parts List
F. Hardware for Handwheel ........2 screw (3/16-24 x 1/2 in.) ........2 flat washer (3/16 in.) ........... 2 Hardware for Mounting Switch Assembly square head nut (1/4-20) ........2 screw (1/4-20 x 3/8) ..........2 Figure 2 c ® TABLE SAW 315.228510... - Page 12 (5/16-18 x 1 in.) ...... 4 hex bolt (5/16-18 x 1/2 in.) ......... 8 hex nut (5/16-18) ..........12 R. Hardware for Motor Mounting Plate ....1 hex bolt (5/16-18 x 5/8 in.) ......... 2 Fig. 2 d ® TABLE SAW 315.228510...
- Page 13 (5/16 in.) ........... 8 hex nut (5/16-18) ..........8 Fig. 2 e Hardware for Mounting Saw Base ..... 1 hex bolt (5/16-18 x 1/2 in.) ......... 4 flat washer (5/16 in.) ........... 8 hex nut (5/16-18) ..........4 ® TABLE SAW 315.228510...
-
Page 14: Tools Needed
8 mm, 10 mm, and 12 mm HEX KEYS (PROVIDED) 2 mm, 3 mm, 4 mm, 5 mm, and 6 mm COMBINATION SQUARE HAMMER ° TRIANGLE WRENCHES: 8 mm, 10 mm, and 12 mm ADJUSTABLE WRENCH FRAMING SQUARE Fig. 3 ® TABLE SAW 315.228510... -
Page 15: Labels
Guard Must Be In Place MODEL 315.228510 SER. NO. During Use. MADE IN TAIWAN NRTL/C SEARS, ROEBUCK AND CO. STATIONARY TOOL Align and • Tighten Customer Help Line 1-800-932-3188 Riving Knife Fasteners Before Use. Fig. 4 a ® TABLE SAW 315.228510... - Page 16 • Disconnect the saw from the power source before See instructions for ripping. changing blade or servicing. Turn Counterclockwise to • Never reach around or over saw blade. • Do not expose to rain or use in damp places. Lower Blade. Fig. 4 b ® TABLE SAW 315.228510...
-
Page 17: Features
Operation section of handwheel on the side of the cabinet. A bevel scale this manual for the basic cuts: cross cuts, miter cuts, on the front of the cabinet shows the blade angle. bevel cuts, and compound cuts. ® TABLE SAW 315.228510... -
Page 18: Assembly
3HP, with capacitor start and V-belt drive, and is BLADE - This saw is provided with a Craftsman 40 housed in a sturdy steel base. tooth, 10 in. carbide tipped blade. The blade is...